What is the order in which the computers are assembled? What is the correct order to assemble a comp

There are many small steps, install heatsinks, motherboards, hard drives, etc. Before and after.

1.Open the box of the motherboard, there is a square sponge inside, pad it with that sponge, put the motherboard on it (to protect the motherboard), install the radiator bracket first, and then open the CPU button (do not use the motherboard button to open the different, see the manual) to install the CPU, coat the heat dissipation silicone, and then install the radiator.

2.Unpack the case, according to the screw holes of your motherboard, install the copper nails that come with the case (copper hexagonal posts are loaded with nails, and tighten them properly with pliers), install the socket stops that come with the motherboard, and then install the power supply. Then estimate the position of the hard disk optical drive (considering ventilation, cable length, aesthetics, etc.), fix it with 1 or 2 screws first, and then put the motherboard on it, the position is suitable, and then fix the motherboard hard disk optical drive, etc.

Install memory. 3.Wire wiring. Arrange the location of the line, install it, fix it, and make it convenient for ventilation and heat discharge.

General Socket Locations:

On the upper left side of the motherboard, there are 4 8 sockets, black or milky white sockets (there are square sockets, D-shaped sockets, etc., corresponding to the sockets), which is the auxiliary power supply socket of the motherboard. Find the corresponding interface in the power supply and connect it.

On the top right, a long strip of 2 8 sockets, memory sockets. In the upper right, next to the memory socket, there is a row of ports, which are the motherboard power supply sockets.

At the bottom right are the hard disk socket and the optical drive socket.

The lower left is the wiring socket position such as the chassis socket start button (read the book to find the corresponding position socket, you can rest assured that it will be plugged in, and it will not burn out if it is not plugged in correctly).

4.Set up the BIOS, partition the hard drive, and reinstall the system.

The process and steps of computer host installation: first prepare the tools and components, then disassemble the CPU box and the motherboard, install the CPU in the corresponding card slot of the motherboard and install the cooling fan; After that, install the power supply in the case, and at the same time fix the motherboard inside the case; Then install the memory card, graphics card, etc. on the motherboard, observe the chassis structure, connect the connection cables of the motherboard and graphics card to the power supply, and fix the cables.

Step 1: Tools and Components. First of all, you need to prepare the corresponding tools, such as a screwdriver and a screwdriver, and usually a simple tool is included with the purchase of the case. At the same time, you should also prepare the various components of the host such as the motherboard, graphics card, memory module, CPU, power supply, chassis, etc.

Step 2: Install the CPU. The installation of the host starts with the CPU, unpack the motherboard and the CPU, take out the motherboard, find its CPU interface position, press down the lever to open it, and then take out the CPU and align it, the action should be gentle and careful to avoid the CPU pins being bent.

Step 3: Install a cooling fan. If it is a boxed CPU, it will have its own cooling fan, so you can install it on the motherboard with the CPU. If you buy a cooling fan yourself, you need to apply silicone grease to the CPU before installing the fan.

Step 4: Install the power supply. Put the motherboard with the CPU next to it, disassemble the case first and then install the power supply, here you need to tighten the screws with a screwdriver, fix the power supply in the case, and remove some cards on the back of the case to facilitate the installation of the motherboard later.

Step 5: Install the motherboard. After the power supply is installed, you can fix the motherboard inside the case, determine the installation direction, and then use screws to fix the motherboard, be careful not to make a mistake, you can look at the slot of the graphics card to determine, it is generally easier to find the direction.

Step 6: Install the graphics card. After that, take out the graphics card, align it with the slot and install it, and fix the graphics card on the chassis with a screwdriver to ensure that the graphics card does not shake from side to side, and the interface of the graphics card needs to be facing the outside of the case.

Steps to assemble the computer: x0dx0ax0dx0a First Prepare the accessories for assembling the computer and a screwdriver, and be sure to remember to eliminate static electricity from your body; x0dx0a Second, install the CPU and memory on the motherboard (before that, you should set up the motherboard jumper according to the actual situation); x0dx0a third opens the chassis; x0dx0a Fourth, install the power supply; x0dx0a fifth: install hard disk, floppy drive, optical drive; x0dx0a 6th Install the motherboard; x0dx0a 7th Install graphics card, sound card, etc.; x0dx0a 8th Connect the power cord; x0DX0A 9th connection data cable; x0dx0a tenth mounting baffle; x0dx0a Finally, close the chassis lid; x0dx0a is that simple. x0dx0a to connect keyboard and mouse:

Finally, it is necessary to connect the main unit with the monitor, keyboard and other components. Because assembling a computer is just assembling the console. Let's connect the keyboard first, the keyboard interface is at the back of the motherboard, which is a round one.

There is an upward marker on the keyboard plug, just plug it in this direction when connecting. This round-mouthed PS 2 mouse is plugged into the mouse jack on the top of the keyboard; If you buy an AT motherboard and don't have this round mouse jack, you have to buy a serial mouse and connect it to a 9-pin serial connector. x0dx0ax0dx0a to connect monitor and speaker:

Connect the signal cable of the display, the 15-pin signal cable is connected to the graphics card, and the power supply is connected to the host power supply or directly connected to the power socket. Be careful not to push too hard. Usually the active speaker is connected to the speaker port or line-out port, and the passive speaker is connected to the speaker port.

x0dx0ax0dx0aFinally, connect the power cord of the primary chassis.

Install the CPU first, then the CPU fan, then the memory module, install the motherboard into the chassis, install the hard drive and graphics card, then install the power supply, and plug in all the cables. Close the cover and the system can be installed. Very simple.

Determine the motherboard first.

The motherboard determines what CPU you want to use, and the CPU installation of AMD, INT is a bit different and not universal.

Then the graphics card, the memory, the hard disk, the chassis, and finally the power supply.

The power supply needs to depend on your configuration decision, otherwise the power is small and you can't bring it up, and finally it is the peripherals, mouse keys, monitors, cameras, headphones, microphones to see the demand.

The general installation sequence is: motherboard - CPU - memory - heat sink - fan - chassis - graphics card - power supply - hard disk - wiring - screws - wiring - successful installation.

The specific installation sequence is as follows:

1. The first step is to open the top cover of the CPU slot, align the gap of the CPU with the gap of the CPU of the motherboard and the edge of the vertical stove, and then gently put it down, pay attention to the alignment and not overexert force, so as not to break the needle.

2. The second step, after placing it, cover the top cover, then press the safety bolt, first slowly push it out and then press it down, and then push it back in, so that the installation of the CPU can be accurate.

3. The third step is to align the screws of the computer fan with the screws of the motherboard, and then put them down smoothly.

4. Step 4: Install the memory module, align the notch at the bottom of the memory module to the notch on the motherboard, and then find the notch at the bottom of the memory module and align the memory module bottom bracket. After finding the correct position, press down on the memory module, close the safety bolt, and make it firmly fixed to the motherboard, so that the installation steps of the memory module are completed.

5. The fifth step, install the optical drive, remove the optical drive baffle on the front panel of the chassis, the disassembly of the optical drive baffle is very simple, and this step is omitted here. Then push the front of the optical drive forward into the optical drive position.

6. In the first six steps of the debate, push the optical drive to the end, and after hearing the sound of "click", it means that it is completely aligned with the chassis, and the optical drive is basically installed at this time, and then the optical drive baffle can be installed back.

That's all there is to it.

First of all, it doesn't matter the order of the power supply, motherboard, graphics card, CPU, and memory module. When these are installed, you can connect the power cords and plug-in cables of the optical drive and hard drive. If there is a trace of the front panel, you can connect the sound and the wiring of the U disk at this time, so that the installation is basically completed.

Zheng Sheng shouted Lu Feng, the power supply and motherboard must be installed first.

The assembly order of the computer host is as follows: motherboard, CPU, memory module, graphics card, sound card, and driver.

Eight major accessories: CPU, motherboard, heat sink, memory, chassis, power supply, graphics card, hard disk (HDD SSD).

CPU identification: There are two types of CPUs commonly found on the market: AMD and Intel.

AMD and Intel are very distinctive, AMD still uses pins (called PGA package), while Intel already uses contacts (called LGA package, and the pins are placed on the motherboard). So AMD's CPUs look relatively high, and Intel's CPUs are relatively flat. Because AMD's pins are on the CPU, receiving the CPU requires a simple look to see if the pins are bent.

It doesn't matter in order, as long as you feel convenient, you can go in whatever order you want.