How to solve the rain leakage in the bay window? Bay window leakage, how to solve this?

Baywindow waterproofing causes and solutions.

Waterproofing practices for dealing with bay windows that leak due to lack of consideration:

The fixed body is additionally treated to the basal layer.

The rainproof board at the junction of the window frame and the concrete body should be close to the concrete body, and the screw cap of the screw and the hole of the concrete screw can be filled with polyurethane sealant. The basal layer also has to be treated with special treatment.

Install a water choke.

We can install a water barrier on the inside of the bay window frame.

Repair of bay window structures.

The drip groove structure is adopted at the top of the bay window to prevent water accumulation on the top of the inner bay window;

The standard of the waterproof layer should be to apply the waterproof layer, so that the end of the waterproof layer at the junction of the wall should also be sealed;

The width of the bay window should be repaired at more than 100mm; If it is not possible, then it is necessary not to use a waterproof layer of coated film, but to choose a thin waterproof layer, etc., and increase the drainage slope of the water pipe, so that you can take anti-condensation treatment on the top layer.

Causes of water leakage in the inner bay window and waterproof solutions for the bay window.

There are also problems such as improper construction and waterproofing practices of bay windows that cause water leakage due to material selection

Remove the original aged sealing material and clean the sealing part.

A certain proportion of waterproof sealant is mixed with waterproof powder, and then mixed into a waterproof sealant with super adhesive strength, and finally the joints between the glass and the aluminum alloy are filled densely.

Use structural adhesive to seal all the joints between the glass and the aluminum alloy window frame, so as to strengthen the compactness of the glass glue and delay the aging of the material caused by the erosion of the glass glue due to sunlight and other corrosion.

Bay window drip sink breakage. The method is to ask the master to reinstall the drip trough, so that the water can be smoothly discharged through the drip trough.

Generally, there will be a drip groove in the window, and the drip tank is an important drainage channel for the bay window, but often due to the installation modification of the bay window, the window moves out and squeezes into the drip groove, resulting in water leakage.

Generally, modern bay windows are equipped with drainage holes, but the drainage holes may be blocked due to installation problems, and this happens from time to time when installing bay windows.

Hello, see your situation, my family has encountered it before, one reason is that the outside of the cold-proof layer is not well treated, so it leads to rain leakage, second, is that there is no waterproof treatment inside, if the waterproof treatment should be better!!

This seepage is difficult to deal with, if you want to solve it completely, it is best to test first to find the leakage point and then deal with it, after all, the insulation layer of the exterior wall is very thick now, and the leakage point will be very troublesome to find.

The bay window is leaking, ** it is likely that the air conditioning position upstairs is not connected to the water pipe, you should contact the property to check whether the air conditioning position on the exterior wall is not connected to the water pipe, and whether there is a crack in the exterior wall that causes water seepage. If you can't find the leakage, you should contact a professional repair company to check it.

Answer 1: When we find that it will leak, we must first carry out waterproof leakage treatment, we need to remove the aging shell or cracked sealing materials, but it should be noted that there can be no oil, dust or other impurities on the surface.

2. We can go to the store to buy some waterproof powder, and then mix it with water in a certain proportion, its mixture has a very strong binding ability, which is equivalent to sealant. But when doing this, you need to make the surface flat, smooth, smooth, and free of chips and holes.

3. Or we can use structural adhesive to glue the connection position of the glass and aluminum alloy window frame, and then do a good job of reinforcement and sealing treatment at the leakage position, which can reduce the material aging phenomenon caused by the erosion of glass glue due to sun and rain.

Find a professional to repair it, you can't do it yourself.

In fact, the bay window is a very unique color, we need to leave a good slope bottom in the decoration design, preferably against the water. Wei Qiang is best to use thermal insulation mortar for painting, if the bay window connection is not sorted out during the decoration, there will be water leakage in the later stage. The bay window leakage can not be solved for a while, so it is simple and rude, and a telescopic awning is installed at the top of the window, which is not expensive, the appearance is quite foreign, and the shape and color look like what you like, usually half-open.

When you buy a pack of cigarettes during installation, ask the master to seal the bottom.

I don't know the age of the house and the specific construction process, let's say it separately, the general bay window is concrete, since it is a leakage, then it means that the house has imperfect structural construction technology in the construction process, and there should be gaps on the concrete surface; exterior wall plastering layer construction or material quality problems; Aluminum quality problems or manual production problems of windows; If the angle with the outer wall is convex, then the rain that comes in will also be scattered outward along the outer wall or drifting, not inward, so you can avoid the appearance of rain leakage.

If the window frame is installed in a problem, clean up the original rubber dust outside, and then re-glue, if it is a bay window seepage, go to the window to see if there is a bulge, if there is a bulge, the bulge should be cleaned up, and then repainted. Most of the reasons for the leakage of the bay window are due to the different waterproof materials used when doing waterproofing during decoration, which leads to the leakage caused by the infirm connection of the joints. There is also a possibility that there are bubbles in the cement inside the tile when the tile is pasted.

When it rains, all the joints between the glass and the aluminum alloy window frame are sealed with structural adhesive, so as to strengthen the compactness of the glass glue and delay the aging of the material caused by the erosion of the glass glue due to sunlight and other corrosion.

Use waterproof powder to mix a certain proportion of waterproof sealant into a waterproof sealant with super adhesive force, and fill the joints between glass and aluminum alloy densely. Locally, use high-quality special glass structural adhesive to repair cracks and areas that are not tightly sealed.

If your bay window can be removed, then you can completely remove the window and apply a layer of waterproof paint, which can effectively prevent rain and seepage.

The glass should be sealed first, if the glass does not leak, then there will be no water on the bay window, and the most important thing is to check whether the glass is rotten.

Just take a 3m waterproof glue and stick it, which is simple, convenient, cheap and durable.

You can put some towels to block the leaky part of the bay window, or you can put some sponges to absorb water, which can deal with the rain leakage well.

We can use glass glue or seam to polish all the gaps in the bay window, and be sure to use some waterproof agent to wipe the perimeter of the window, so that the problem of water leakage can be solved.

You should first find the leaks and then fill them up in the good weather, and do so.

The gaps should be filled, the gaps around the bay window should be filled so that it does not leak.

A good rainproof equipment should be installed in the window, and the window must be closed in time, and it is best to choose a tighter window when choosing a window.

You should first find the leaking place, plug the leaking place with a rag, and then use some foam glue or glass glue to fill the leaky place when it is not raining.

If that's the case, I really recommend that you should change the windows, most likely because the windows are not well sealed, so there is a rain leak.

First, the waterproof design of bay windows is not fully considered.

At first, the design of the bay window was not fully considered. The original design only considered the waterproofing of the top of the bay window and the interface of the external wall, ignoring the waterproofing treatment of the interface of different materials. The exterior walls are richer in decoration than before, with more lines.

The thermal expansion coefficient of various materials is different, and the upper waterproof layer is not considered in place, which is easy to produce cracks and cause water leakage.

Two. Improper handling of construction details.

In short, due to poor handling of construction details and some management deficiencies, gaps were formed between the concrete partition wall and the exterior wall. Although the roots are outside, the bay window will definitely leak on rainy days.

Because the bay window waterproofing measures that cause water leakage are not taken into account:

Locate the cadaver and dispose of the basal lamina.

The flashing at the junction between the window frame and the concrete body should be close to the concrete body, and the nut cap and concrete screw hole can be filled with polyurethane sealant when fixing. The foundation slab must also be treated with special treatment.

Set up the waterproofing plate.

Waterproofing panels can be installed in the frame of the indoor bay window.

Repair the bay window structure.

1) The top of the bay window adopts a drip groove structure, which can prevent water accumulation on the top of the inner bay window;

2) The waterproof layer standard should be coated with a waterproof layer, so that the wall joints at the end of the waterproof layer should also be sealed;

The width of the cornice of the bay window should be repaired if it exceeds 100mm. If not, don't use a coated waterproofing layer. A thin waterproof layer should be selected to increase the drainage slope of the water pipe to prevent condensation on the top layer.

Causes of water leakage in bay windows and moisture-proof measures.

There are still some problems in the selection of materials, such as improper construction, etc., which leads to water leakage in the windows.

Remove the original aging sealing material and clean the seal.

The waterproof powder is mixed with a certain proportion of waterproof sealant, and then blended into a waterproof sealant with strong adhesion. Finally, fill the seam between the glass and the aluminum alloy.

Sealing all joints between the glass and the aluminum window frame with structural adhesive can enhance the compactness of the glass glue and prevent the aging of the material caused by sun and rain.

1. What should I do if the bay window seeps water into it when it rains?

1. If there is water seepage in the rain of the bay window, it is necessary to check the specific location of the leakage, and then deal with it. If water leaks from the outside of the window, it is most likely that there is a problem with the seal, and the original sealant needs to be removed, and then the gap should be filled with foam filler, and then the sealant should be re-applied.

2. If it is the leakage of the bay window itself, then you need to look at the tiles of the exterior wall to see if there is a gap, if there is, you need to use a special caulk, fill it into the gap, and paint it with the same color as the exterior wall, you can prevent water leakage again.

3. In addition, it is also possible that there is a problem with the side wall of the bay window, and the time of its reinforced concrete construction is not the same as that of other exterior walls. Instead, wait for the other exterior walls to be poured before pouring the side walls of the bay window, which requires waterproof construction for the side walls to ensure that there will be no water leakage.

Second, who needs to deal with the water leakage of the bay window.

1. If the house is still under warranty, you can contact the developer to deal with it. Or let the property know and ask them to help coordinate with the developer. If the quality of the house itself is a problem, then the developer needs to contact the construction unit to carry out the repair work.

2. If it cannot be solved through the coordination of the developer, you can go to the relevant local departments to apply for housing quality inspection and make complaints. After the problem is determined, the relevant person in charge can be arranged to repair it.

3. If there is water seepage in the bay window when it rains, and it is determined that the quality is not up to standard during the decoration, then the owner is responsible for it. The owner needs to find the renovation worker at the time to repair it.

Summary: What to do if the bay window seeps water into it when it rains, and who needs to deal with the water leakage of the bay window, I will introduce it here first, do you understand it? If there is water seepage in the rain in the bay window, you need to find the cause in time to avoid trouble.

On rainy days, the bay window leaks, which is the more troublesome thing that every family with a bay window has to face, how to solve this matter, you can only find professional personnel to do waterproofing on the bay window, or seal all the gaps with glass glue, and generally you can fundamentally solve the problem of bay window leakage.

The reason is not complicated, but it is not easy to maintain, it needs to be constructed from the outside, involving high-altitude work, you must find professional waterproof workers, and you must also have experience in high-altitude work.

Repairs cannot be chiseled because the silt will fall and there is a safety risk, so it can only be done on the base of the existing façade. To consider the reasons for weather resistance and adhesion, it is recommended to take two steps, the first step is to use high adhesion and strong weather resistance epoxy for waterproofing, and the second step is to protect with waterproof mortar and raise the base surface to form a drainage slope. No water accumulation, no leakage, combination of anti-drainage.

Hello 1

The waterproof design of the bay window was not considered at the beginning, and the original design only considered the waterproofing of the top of the bay window and the intersection of the exterior wall, ignoring the waterproofing treatment at the interface of the connection of different materials. The decoration of the façade of the exterior wall is richer than before, the lines are also increased, and the temperature expansion coefficient of various materials is not the same.

On rainy days, the bay window is always seeping water, is there any way to solve it? If the bay window is always seeping water on a rainy day, is it because of the direction of the window?

If you don't want to redecorate, it is recommended to leave that area vacated so that the tiles don't fall and hurt people.

Add another layer of glass to the outside of the bay window so that no water can seep in.

Many people will not notice the problem of water leakage in the bay window when buying a house, when it rains more on a cloudy day, the bay window seeps, and everyone realizes that it is time to waterproof the bay window, but at this time the water seepage has already happened, if we are in.