How to take off the lens protection ring ring of iPhone6?

There are two ways:

Type 1: 1Use a toothpick or fingernail to stick it in the gap.

2.Gently flick the ring, and the lens protector will come down directly.

<> second type:1Take an Apple-specific screwdriver to disassemble the screw port next to the charger at the bottom of the phone.

2.Open the back case and remove the lens protector.

<> iPhone is a series of smartphones developed by Apple in the United States, equipped with the iOS operating system developed by Apple, and Jobs revealed the launch of the first generation of iPhone at Apple's annual meeting of global software developers in 2007 at the Mascoconi Convention Center in San Francisco.

At 1 a.m. Beijing time on September 10, 2014, Apple officially unveiled its next-generation product, the iPhone 6, at the Flint Center for the Arts at De Ansar College in Cupertino, California.

1. The first step is to insert a toothpick or a fingernail into the gap. As shown in the figure below:

<>3. Then gently remove the lens protection ring with your hand. As shown in the figure below:

1. The first step is to use a toothpick or fingernail to insert it in the gap. As shown in the figure below:

<>3. Then gently remove the lens protection ring with your hand. As shown in the figure below:

Take Apple's special screwdriver to disassemble the screw port next to the charger at the bottom of the phone, open the back case, and then remove the lens protection ring.

I was also searching for the answer to this question just now, and I tried the method they said, either it was troublesome or it didn't work, and then I pondered it myself, and found that there was a way to try, anyway, I took it down, that is, first you have to have some nails, and then gently turn the lens protection ring, turn a few more times, turn back and forth, and then pick it with your nails, and try it a few more times to buckle it off, I just succeeded, and I came to reply.

I use a line, then circle it, get the line in hard, pull it hard and it comes out! Zero violence

It is recommended to use a small diagonal pliers electronic clamp to clamp it, and it will jump out as soon as it is warped. You can try it if you can't do anything with a knife or a fingernail!

Use a thread to sew clothes, wrap it in the gap a few more times, and then lift it up, and it comes out, test it yourself!

Use the thin thread in the sewing kit, then circle it, pull it outward, and it will fall off.

Use your teeth safely** with trouble-free personal testing.

Use nail clippers to hold the position of the ring and pull it up, you don't need to use a razor.

I gritted it with my teeth, and it came down as soon as I pulled it out.

I bit it down with my teeth and it went down.

With nail clippers, I just took it out.

Nail clippers, clamp the inner ring and pull it out gently.

Hold it up with a thin pair of scissors and come down, just got it down.

How can it be so troublesome, it will fall off with a light pick with your fingernails from the top!

I bit it down with my upper and lower teeth and I just tried it.

Use the tip of the knife against the circle to forget to scrape, scrape hard a few times, and don't listen to change directions.

I have a good method, which has been successfully experimented, without harming the fuselage, and can also remove the protective ring.

Do you know the fake nails that women use for manicures? You go and buy a few of them, and the material and hardness are just right. Don't buy one, because the quality is different, some are soft, some are okay, you buy more than 5, don't buy the thumb one.

After buying it, start from the top of the protective ring, insert it through the gap, turn the fake nail half a circle, and then use your real nail to buckle it down.

You can't take it off, although it's ugly, bring a condom.

With my teeth, I don't know how to get on the picture, anyway, I just bit it with my teeth and rotate it, it's OK.

I took the thread of the sewing clothes, held the two ends in my hands, and it came down with a gentle tug, and it didn't hurt the lens, I tried it, and it was very effective.

As long as it's not dirty, it comes out by biting it with your teeth.

The nail clippers come off in one go! Try it yourself!

Try it yourself, just succeeded, and it came down with a bite of your teeth, you can try it.

Methods and tips for maintaining your camera:

1. First of all, you need to keep the camera clean and make sure that the place where you install your phone is clean, so that in the process of carrying, the probability of contamination will be reduced.

2. You can develop the habit of cleaning the camera with clean wiping paper regularly, and you can use alcohol when appropriate. It is not advisable to use toilet paper to wipe the lens, as doing so will leave fine confetti behind. At the same time, when wiping with a cloth towel, you should also make sure that the cloth towel is clean and free of impurities, otherwise it may scratch your lens.

3. If there is dust on the camera, you can consider using special adhesive tape to stick the dust down, such as the cleaning work done by professionals before applying the film to the mobile phone.

4. It is best not to put the camera facing up when placing the mobile phone, because it is easy to fall dust, and in the case of a lot of dust, try not to expose the mobile phone.

5. It is best not to put hard objects and mobile phones in one place, although the screens of most mobile phones can resist scratches by metal hard objects such as keys, but many camera lenses do not meet the hardness requirements.

6. Another point to note is that it is not advisable to stick the camera with plastic tape, the transparent tape is acidic and weakly corrosive, and the transparent tape is used as a protective film, which may make the lens blurry after a long time.

7. Of course, for some users who want to make it easy, if they want to protect the iPhone6 convex camera, they can buy a lens protector and install it on the lens. The advantage is that it will not affect the feel, and at the same time, the lens protection frame is heightened, which can greatly protect the mobile phone lens from being scratched, and it will not affect the clarity of imaging when taking pictures.

I just took it off, clamped it tightly with nail scissors, don't touch the camera, and it came out with a pull.

Is the protective ring glued on? If you blow it a few times with a wind gun (if you don't have a hair dryer), you can take it down. If it is not glue, it is recommended to prevent damage to the camera when it is hard to warp it after the after-sales service.

With nail clippers, I grabbed the outer ring and the inner ring and gently pulled it down, I just tried it.

Take the cotton thread and wrap it around it, tighten it, and then take the cotton thread away, and it will fall off as soon as you pick it This is how I picked it, the original method.

Hello, take a small blade and pry it open.

The teeth clenched upstairs and it was a success.

Use a very thin, thin blade. Go to the stationery store and ask him to buy the kind of squeezing sulfuric acid paper. Then slowly and slowly stuff it in from the antenna, and then gently shake it twice. Don't be vigorous, and use your fingernails to pick out the gaps after you see them.

I tried it myself, and I just succeeded, and I came down with my teeth.

Gently insert a blade into the gap and you'll be able to get straight down, but if you're not sure, try it with a toothpick or something.

Hold it with small scissors and pull it out......

The answer on the Internet is that you can't use your fingernails or knives to get out! It is recommended to use electronic pliers to clamp and jump out as soon as it is clamped! Be careful not to hurt your phone, rest assured. I hope to adopt!

Take Apple's special screwdriver to disassemble the screw port next to the charger at the bottom of the phone, open the back case, and then remove the lens protection ring.