How is the color steel sandwich panel installed?

Color steel sandwich panel is a more common material in recent years, which is pressed by two layers of metal plates and a polymer thermal insulation inner core in the middle. Color steel sandwich panels are widely used in various buildings, which can play a good role in sound insulation, flame retardant and thermal insulation. Its light weight and easy installation make it one of the best boards.

The following is an introduction to the precautions for the installation of color steel sandwich panels and the characteristics of color steel sandwich panels. Before the installation of wall panels and ceiling panels, the materials, varieties, specifications, sizes, properties and core materials of the sandwich panels should be inspected to verify whether they can meet the design requirements; If necessary, the sample is tested for performance (fire resistance, safety and non-toxicity, flexural strength, etc.). Before the installation of the wall panel and the ceiling panel, the hidden works that have been constructed on the ceiling and the sandwich wall should be accepted and accepted, and the qualified requirements should be met before the construction of the wall panel and the ceiling board can be carried out.

When installing high-efficiency filter air outlets, lamps, temperature-sensing and smoke sensing elements, speakers, and doors, windows, and pipelines, the openings of ceiling panels and wall panels should be smooth, tight, clean, and non-dust-producing, and their gaps should be sealed with non-combustible materials; The perimeter of the inspection port should also be well sealed.

The seams of the ceiling board and the wall board should be uniform, the gap error of the board joint should not be greater than mm, the plate joint should be evenly sealed with sealant, and the sealing place should be flat, smooth and slightly lower than the board surface. The installation of the wall panel should be vertical, the installation of the ceiling plate should be horizontal, the plate surface should be flat, the position should be correct, and there should be a reasonable structure at the junction between the wall and the ground, the wall and the top, the wall and the wall, and the top and the top to ensure that the seal is sealed and cracked, and the corners should be rounded. After the plate is installed, it should be protected to prevent collision and damage to the board surface.

Self-tapping screws can be threaded through the wall panels and in this way directly attached to the wall substructure. It can also be indirectly connected to the wall substructure by using self-tapping screws through the connectors. Generally, the accuracy related to the installation of curtain wall panels is specified as follows:

Its façade has a perpendicularity of 2 mm, which stipulates that its surface flatness is 3 mm. In addition, the seam straightness is millimeters, and the installation must be carried out in accordance with the factory regulations. When installing, you also need to use weathering adhesive.

This is generally used when fixing some edge cinching and flashing boards. Pay attention to the use of weather-resistant adhesive caulking to keep it tight, so that it can effectively prevent gas penetration and rainwater leakage.

Color steel laminboard English name: color steel laminboard, the product is composed of two layers of formed metal panels (or other material panels) and directly in the middle of the panel foaming, curing polymer thermal insulation core. These sandwich panels are easy to install, lightweight, and efficient.

The filling system also uses a closed foam molecular structure, which prevents the condensation of water vapor. Composite methods usually include ** compounding, ** rolling compounding, rolling compounding, etc. Composite materials can be divided into composite plates, composite pipes, composite rods, etc.

It is mainly used in anti-corrosion, pressure vessel manufacturing, power construction, petrochemical, pharmaceutical, light industry, automobile and other industries. Insulation composite maintenance board composed of color-coated steel plate or other panels and bottom plates and insulation core materials through binders (or foaming).

How to install the seven-centimeter sandwich color tile plane.

Generally speaking, if there is no human factor to destroy, the life of the sandwich foam color steel tile is generally more than 25 years, and the specific service life generally needs to be decided according to the surrounding environment of the sandwich foam color steel tile, the user's use and maintenance methods. The service life of the color steel sandwich panel roof is 10 to 15 years. Depending on the use environment, the kitchen.

Farms, places where chemicals are used, because sandwich panels are not preservative, these places are used to shorten the service life.

The life of color steel sandwich panel, also known as color steel sandwich panel) is the wall, and the light steel structure is built as the skeleton. The anti-corrosion layer of color galvanized steel plate is maintained for 10-15 years, so the life can theoretically exceed 10-15 years, but it is also related to the environment, the quality of the materials used and the maintenance method. 10-14 kg square meters, equivalent to 1 brick wall in bright color:

There is no need for surface decoration, and the anti-corrosion layer of colored galvanized steel plate is maintained for 12-15 years. 6.High intensity:

It can be used as the enclosure structure of the ceiling and the load-bearing plate, which is bending and compressive; Ordinary houses do not use beams and columns.

First of all, you have to level the ground, then spread it in the ground with slotted aluminum, fix it with expansion screws, and enclose the area of the house. Then rub it inside with the sandwich panel, remember to hit the rivets below The sandwich panel is rubbed one by one (the sandwich panel itself has a groove) The turning position should be pulled with angle aluminum What kind of C-shaped plate do you have when you buy color steel plates, first fix the C-shaped plate with rivets, and then install the sandwich panel and fix it with rivets.

The main raw material of this sandwich panel is rock wool, so it fully demonstrates the performance of rock wool, fire and heat preservation, heat insulation and sound absorption. This kind of sandwich panel is of better quality and more safe and reliable to use. The use of some flights can be very good sound insulation, and the use of buckle connection method color steel sandwich panel curtain wall installation is completed, we have to from top to bottom, layer by layer to remove the wall panel surface protection tape, and layer by layer dismantling.

Dismantle the shelves, pay attention to the wall panels can not be scratched or bruised. Inspect and clean some binders and dust, etc., to maintain the integrity of the entire construction.

When installing color steel sandwich panels, the panels are usually mobile, but handling is also important, and both ends should be carefully lifted at the same time. This will prevent damage to the oxide film on its surface. When installing wall panels, it is best to lift them one at a time.

The fixture should be specially designed. In general, the manufacturer will have such a fixture. Lifting should be done slowly to avoid collisions.

First of all, you have to level the ground, then spread it in the ground with slotted aluminum, fix it with expansion screws, and enclose the area of the house. Then wipe it inside with a sandwich panel, remember to rivet it below, wipe a piece of sandwich panel (the sandwich panel itself has a groove), the turning seat should be pulled with angle aluminum, the window is vacant, so that you can save a little (of course, you can dig it on the installed wall), the vacant window should be wrapped with grooved aluminum, and then install the plastic steel window, the door itself is cut on a whole page and also wrapped with grooved aluminum, and the top plate above is connected with the wall panel below with angle iron, and the screws are played.

The materials are hoisted to the roof truss in batches, and oblique slings are added on both sides to prevent slipping, all skin ribs are facing up, and the board surface should be in the same direction; Before installation, the purlin support is tested and leveled, and then the support point position is marked according to the requirements, and the purlin is used to do positioning and fixing treatment; Begin to pave the color steel plate from left to right, top to bottom direction; When the sheet is placed, each piece is installed according to the alignment, taking care not to deviate. The laying surface should be fixed with self-tapping screws to ensure that the center of the rib is on the strip; Finally, you can do a good job of closing the edges.

Color steel sandwich panelIt is a new type of material that is more popular at present, which is not only high-tech content, but also very environmentally friendly. But for ordinary people, the perception of it is almost unfamiliar. So what is a color steel sandwich panel?

What is color steel sandwich panel?

Color steel sandwich panel is a common product in the current building materials, which can not only be good flame retardant and sound insulation, but also environmentally friendly and efficient. The color steel sandwich panel is pressed by two layers of metal panels and a middle layer of polymer insulation core. It has the characteristics of easy installation, light weight, environmental protection and high efficiency.

In addition, the closed foam molecular structure used in the filling system can prevent the condensation of water vapor.

As an excellent new type of plate, it not only has beautiful appearance and bright color, but also has good load-bearing, heat preservation, waterproofness, etc., and has a particularly wide range of use. It is mainly used for thermal insulation, fire and sound insulation in production workshops, office attics, decorative building materials, mobile rooms, office buildings, members, cold storage, supermarkets, gymnasiums, warehouses, building mezzanines, clean workshops, etc.

What are the common types of color steel sandwich panels?

In general, color steel sandwich panels can be divided into 6 types, namely polystyrene sandwich panels, rock wool sandwich panels, phenolic sandwich panels, tripolyester sandwich panels, extruded polystyrene sandwich hall core panels, and rigid polyurethane sandwich panels.

If it is classified according to the panel of color steel sandwich panel, it can be divided into two types: metal surface and non-metal panel. Among them, the metal surface has good processing performance, corrosion resistance and impact resistance; The processing performance of non-metal plate is poor, but it is widely used in hospitals, cold storage, supermarkets, gymnasiums and other places.

What are the specifications of color steel sandwich panels?

The production of color steel sandwich panels must be carried out in accordance with certain stool specifications and sizes, and only when certain specifications are met can it be put into normal use. The specifications of color steel sandwich panels include a width of mm, etc.; The length can be determined according to the demand; thickness between 50 250mm; The performance of the core board requires a maximum operating temperature of 100 degrees Celsius, a thermal conductivity of less than 120,120kg m3, and so on.

How much is the color steel sandwich panel**?

Color steel sandwich panel composition excellent thermal insulation, fire and sound insulation board materials, its production cost is high. Different specifications of color steel sandwich panels are different, the general thickness is 50mm, and the conventional specifications of color steel sandwich panels are 36 yuan; The thickness of 75mm conventional specifications color steel sandwich panel ** is yuan; The thickness of 100mm conventional color steel sandwich panel** is 100 yuan. Because the color steel sandwich panel fluctuates greatly in the market, it will fluctuate.

The above is what are the specifications of the color steel sandwich panel brought to you? How much is the color steel sandwich panel**? All of it.

Color steel sandwich panel is one of the common products on the market, which is mainly made of upper and lower layers of metal plates and a polymer thermal insulation inner core in the middle. It is widely used in various buildings, its texture is light, and it has a good sound insulation, flame retardant and thermal insulation effect, and is one of the most excellent boards at present. So what are the specifications of color steel sandwich panels?

1. Specifications and types of color steel sandwich panels.

1. According to the thickness, the color steel sandwich panel can be divided into: 50 mm, 75 mm, 100 mm, 120 mm, 150 mm, etc.;

2. The specifications of color steel sandwich panels are divided into: 470 type, 600 type, 760 type, 820 type, 900 type, 950 type, 1150 type, etc.;

3. According to the sandwich insulation materials, it is divided into: foam, glass wool, polyurethane, rock wool;

4. According to the different parts of the enclosure, it is divided into: roof color steel sandwich panel, wall color steel sandwich panel;

2. What are the characteristics of color steel sandwich panels:

1. The texture is light, and the weight per square meter is only about 24kg, which can reduce the total cost of the structure.

2. Due to its light weight, it can be cut at will during the construction process to meet the needs of special design; It is easy to install, which can improve efficiency and save construction time.

3. Because the base material of the color steel sandwich panel is made of non-combustible or flame-retardant materials, it can meet the requirements of fire protection specifications.

4. The surface layer is treated with a special coating, and the life span can reach 10-15 years, and if the later sister does spraying anticorrosive coating for ten years, the life span can reach more than 35 years.

5. Its lines and colors are numerous and rich, which can meet the needs of any style of building.

6. The sound insulation strength of color steel sandwich panel can reach more than 40-50 decibels, which is a rare sound insulation material.

7. It adopts high-strength steel plate, tensile strength of 5600 (kg cm2), coupled with advanced design and roll forming on the market, so it has excellent structural characteristics.

Conclusion of the article: The specifications and characteristics of the color steel sandwich panel are introduced here, and I hope it will be helpful to you. Color steel sandwich panel is a good material, which can be selected according to needs.