How to set tendaD301 as a wireless router only?

How to set up a wireless router:

1.Connect the wireless router to a higher-level network device (e.g., modem, first-level router).

Connect the WAN port of the router with the LAN port of the higher-level network device with a network cable, and the connection is successful when the WAN port light flashes on the router.

2.Connect your computer wirelessly to your router.

The computer searches for the router's wifi name (the default wifi name is located on the nameplate on the back of the router) and connects to the wifi network. The first time you use the router, you generally don't need to enter the wifi password.

3.Go to the wireless gateway configuration page.

Open a browser, enter the IP address of the router gateway (usually, the default value is located on the nameplate on the back of the router) to enter the gateway configuration page. (This interface will pop up automatically for new routes).

4.Set up a wireless router to access the Internet.

Go to the WAN port settings in Advanced settings. If the broadband service requires dial-up, select PPPoE dial-up, otherwise you can choose DHCP to get automatically. To dial up PPPoE, enter the broadband password, and select Automatic connection as the connection mode.

If DHCP is automatically obtained, you do not need to enter this field.

5.Set the wifi name and wifi password.

Go to Wireless Security in the Wireless Settings and select WPA2-PSK mode for Security Mode. Select AES for WPA encryption rule. Set up a wireless network key.

<>6.After the setting is completed, the router will automatically restart, please enter the new wifi password to connect, and you can access the network.

Connect the modem to the fiber and then to the router.

Directly connect the network cable to the WAN port of the router, then find a short network cable, connect to the computer at one end, and connect to the router 2 3 4 any idle interface at the other end, enter the router management interface and click "Advanced Settings" - "WAN Port Settings" - "Ethernet Interface" - "Add" - select the corresponding physical interface connected to the home network cable - click "Next" - select the corresponding Internet access mode to set up

The corresponding connection mode for ADSL dial-up is: PPPoE

Computer: 1. Connect A301 to the power supply, and connect the computer and A301 with a network cable at the same time, (the desktop computer is only connected to the A301 with a network cable, not a router and other equipment; Disconnect the laptop from the wireless connection, or connect to the WiFi signal of the A301) Open the browser, enter **:, press Enter, and enter the login interface.

2. Enter the password: admin, click OK to enter the setting interface.

4. In the pop-up prompt box, click "OK", the device will automatically restart, and you can verify whether you can surf the Internet after restarting.

Verification method: Verify that the setup is complete:

1. The lights on the left, upper and right sides of the A301 indicator are always on.

Check the original WiFi signal strength, the signal strength means that the setting is complete.

Note: If the status light is flashing and cannot access the Internet, you must check whether there is any error in the settings and check carefully.

Mobile phone: 1. Connect the extender to the power supply.

3.Open the browser of your mobile phone, enter **: enter, enter admin and click OK.

4. Enter the settings interface, click "Turn on Scan" in the judgment, select the enlarged wifi name, enter the password, and click Save.

5. After clicking "Save", in the pop-up prompt box, click "OK", the device will automatically restart, and verify whether the Internet can be accessed after the device is restarted.

Verification method: Verify that the setup is complete:

1. The lights on the left, upper and right sides of the A301 indicator are always on.

Check the original WiFi signal strength, the signal strength means that the setting is complete.

Note: If the status light is flashing and cannot access the Internet, you must check whether there is any error in the settings and check carefully.

Frequently asked questions. 1. Can't enter the settings interface on my phone?

Answer: Please turn off the mobile data first, make sure the mobile phone is only connected to the WiFi signal of the A301, and then try to enter the settings interface.

2. Why can't I find the signal of the previous A301 after setting?

Answer: After the A301 is set, the WiFi name and password will automatically remain the same as the WiFi name and password of the original router, so you can only search for the WiFi signal of the original router.

[Home Network Environment Wiring]:

1. There is a cat (modem): cat (modem) - router WAN port; The LAN port of the router --- a computer.

2. No modem: network cable --- router WAN port; The LAN port of the router --- a computer.

Computer enters the router]:

1. The computer IP and DNS settings are automatically obtained.

2. Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

Set Router Dialing]:

1. In the [Setup Wizard], select [PPPoe Dialing] (some are ADSL Dialing), enter the Internet user name and password according to the prompts, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

After entering the account and password, the advanced settings WAN port status shows that it is connected, and the IP gateway and the like can only be accessed, and some want to clone the MAC address.

In the browser, the output to log in to the account, the password is admin, and then enter the broadband account password! !