The computer won t turn on, and the light of the host computer flashes, making a dripping sound.

You can tell what's wrong with the computer based on the different sounds it makes, 1 short.

The system boots normally.

2 short. General errors.

Go into the BIOS and reset the incorrect options.

1 long and 1 short. There was an error with the memory or motherboard.

1 long and 2 short. Wrong monitor or graphics card.

1 long and 3 short. Keyboard controller error.

Check the motherboard. 1 long and 9 short.

Motherboard flash

RAM or EPROM error.

BIOS corruption.

Ringing (long sound) constantly

The RAM is not plugged in tightly or damaged.

The ram keeps ringing.

The power supply, monitor, and graphics card are not properly connected.

Please check the relevant connection.

Repeat short rings. Power issues.

Silent and no display.

Power issues. ami

BIOS alarm sound meaning and solution.

1 short. Memory charging update failed.

Check the memory. 2 short.

Memory ECC verification error.

Setting the memory option for ECC check to "disabled" in the BIOS solves the problem.

However, the most fundamental solution is to replace a piece of memory.

3 short. Failed to check the basic memory (the first 64KB).

4 short. The system clock is wrong.

5 short. **Processor detection error.

6 short. Keyboard controller error.

7 short. Unexpected processor interrupt error.

8 short. A memory error is displayed.

There is a problem with the display memory.

Replace the graphics card.

9 short. rom

BIOS inspection and check errors.

1 long and 3 short. Memory error.

Memory corruption. Just replace it.

1 long and 8 short. Displays test errors.

The monitor signal cable is not properly connected or the graphics card is not plugged in.

If it doesn't turn on, it is likely that the memory is not plugged in properly, you can try to remove the memory and clean the ash.

The laptop won't turn on, and it rings. Most of them are memory module issues. This problem can be solved after disassembly and cleaning.

The computer host can't be turned on, and the button flashes a yellow light.

The sound of dripping is caused by excessive computer dust, here you can disassemble the computer case, blow the dust inside the method to solve, the specific operation steps are as follows:

1. First of all, prepare a screwdriver.

Use a screwdriver to disassemble the computer case.

2. Then place the memory module.

Remove from the top of the motherboard.

3. Use clean toilet paper.

Wipe the bottom end of the memory module clean.

4. Then there is a lot of dust inside the case, use a hair dryer to blow the inside of the case clean.

5. Place the memory module correctly on the motherboard, ensure that the notch is aligned, press it vigorously, and install it.

6. Finally, reboot the test, there will be no sound at this time, and it can be started normally.

Summary. Hello, 1.Tick....Tick....", a continuous interval of long tones. This is the sound of the memory alarm, which is generally due to loose memory, poor contact between the gold finger of the memory and the memory slot, oxidation of the gold finger of the memory, and failure of a chip in the memory.

2.Tick....This is a graphics card alarm, usually because the graphics card is loose, the graphics card is damaged, or the power supply part of the graphics card of the motherboard is faulty.

The computer host flashed red light and kept dripping, what's going on?

Hello, 1.Tick....Tick....The continuous interval of the long or leaseback tone. This is the sound of the memory Shixiao alarm, which is generally due to the loose memory, the poor contact between the gold finger of the memory and the memory slot, the oxidation of the gold finger of the memory, and the failure of a certain chip of the memory.

2.Tick....This is a graphics card alarm, which is generally caused by a loose graphics card, damaged graphics card, or a faulty power supply part of the graphics card on the motherboard.

And the host computer can't be turned off yet.

It can't be turned off, the display screen is still sleeping, only the host is ringing, and the fan is ringing all the time.

How long has it been since you've cleaned a fan.

But my console has only been used for more than five months.

That's not a fan problem, sometimes it will drip if you don't clean it for a long time.

Your drip sound is like that.

There are discontinuities or long tones.

There was a break, and the drip was finished, and then the red light flashed again, five times every few seconds.

There may be a problem with the memory and graphics card, do you have any experience in repairing.

Are you sure, I didn't (I wouldn't have asked you if I had).

I mean, if you have it, you can get it yourself, and if you don't, I suggest you find someone to get it<> okay, goodbye.

1 Short: The system starts normally. This is something we hear every day and it also shows that there is nothing wrong with the machine.

2 Short: General error, please go to CMOS setup and reset the incorrect option.

1 Long 1 Short: There is an error with the RAM or motherboard. Try to change the memory, if it still doesn't work, you have to change the motherboard.

1 Long 2 Short: Wrong monitor or graphics card.

1 Long 3 Short: Keyboard controller error. Check the motherboard.

1 Long 9 Short: Motherboard flash RAM or EPROM error, BIOS corruption. Try a different block of flash ram.

Constant ringing (long sound): The memory module is not plugged in tightly or damaged. If it still doesn't work, you can only replace a memory module.

Ringing: The power supply and monitor are not properly connected to the graphics card. Check all the plugs.

Repeated short rings: Power supply issues.

No sound, no display: Power issue.

When the computer is turned on, it can't be turned on, in this case, it is a BIOS alarm, and your computer can be repaired according to the sound characteristics of the alarm.

1 short, the system starts normally, indicating that there is no problem with the machine; 2 short, the routine is wrong, please go to CMOS setup and reset the inaccurate options.

Constitute. Typically, the host computer is a general-purpose electronic computer with internal memory and peripherals. Internal memory is used to store the programs required for data processing, the raw data, and the intermediate results of the processing. Peripherals include external memory and input and output devices.

Disk memory and tape drives are commonly used as external storage, the former is used to store operating systems, system files, batch processing data, and build databases; The latter is mainly used for the recording of receiving and sending information for long-term archiving, and is also used for program debugging and fault testing.

Input/output devices include keyboard displays, line printers, X-Y plotters, and graphics terminals. Depending on the size of the system, the host should have sufficient data processing power to efficiently process randomly occurring data information.

If the computer can't turn on, it always ticks and ticks, if it is a non-stop short ring, the main power supply, the monitor is not connected to the graphics card, etc. 1The POST alarm sound description of the award BIOS is as follows: 1 Short:

The system started normally and there was no problem with the machine. 2 Short: Regular error.

Please go to BIOS Setup and reset the incorrect options. 1 long and 1 short: RAM or motherboard is wrong.

1 Long 2 Short: Wrong monitor or graphics card. 1 long and 3 short.

Keyboard controller error. Check the motherboard. 1 long and 9 short.

Motherboard flash RAM or EPROM error, BIOS corruption. Constant ringing (long sound): The memory module is not plugged in tightly or is damaged.

Non-stop ringing: The power supply, the monitor is not properly connected to the graphics card. Check all the plugs.

No sound and no display: There is a problem with the power supply. 2.

The AMI BIOS POST alarm sound is described as follows: 1 Short: Memory refresh failed.

Replace the memory module. 2 Short: The memory ECC verification error is incorrect.

Please go to BIOS Setup and reset the memory to Disable, but the fundamental solution is to replace a memory. 3 Short: System base RAM (first 640KB) check failed.

Change memory. 4 Short: The system clock is wrong.

5 Short: CPU error. 6 short.

Keyboard controller error. 7 short: The real mode of the system is wrong and cannot be switched to protection mode.

8 Short: A memory error is displayed. Just change the graphics card.

9 Short: ROM BIOS Verification and Error. 1 long and 3 short.

Memory error. 1 long and 8 short: A test error is displayed.

The monitor cable is not plugged in properly or the graphics card is not plugged in properly. 3。The POST alarm sound of the compatible BIOS is described as follows:

1 Short: The system starts normally and there is no problem with the machine. 2 short.

The system power-on self-test (POST) failed. 1 Long: Power error, if there is no display, it is a graphics card error.

1 long and 1 short: The motherboard is wrong. 1 long and 2 short.

Error card is displayed. 1 Short 1 Short 1 Short: Power supply error.

3 long and 1 short: keyboard error. What you said may be that the BIOS alarm is long and short, it is the motherboard error, if you can use it, you can restore the BIOM, no, put the COMS battery on the motherboard and try to take down the round battery on the motherboard, and put it back on after a minute.