-
Anonymous users2024-02-07Turn the notebook over, pay attention to the structure of the notebook, and don't remove all the screws. It's more cumbersome to put it back in this way.
After opening the cover covering the hard disk and memory, pay attention to the positioning screws of the optical drive. Generally, there will be a screw a little behind the position where you can see the optical drive.
After removing the positioning screws, you can pull the optical drive outward, and the force used here should be moderate. Because there are some notebooks that don't have more than one set screw. When pulling, pay attention to whether the piece of iron on the locating screw you just removed will move.
If it moves, it means that there is nothing wrong with the screw that was just folded.
If you can pull the optical drive, it means that you can connect it directly.
After taking out the notebook optical drive, it depends on your own needs whether you want to change the optical drive, or clean the optical drive, or install the optical drive on the hard disk.
-
Anonymous users2024-02-061.Prepare tools: small flathead screwdriver, thin wire.
2.Loosen the 4 screws under the optical drive with a screwdriver.
3.Insert a small hole in the front with a thin wire and the tray will pop out.
4.Use a screwdriver to pry out the front panel by pressing the clips on both sides.
5.Then use both hands to push the front panel outwards and remove it.
6.With both hands, pull the optical drive out of the iron case.
7.At this point, the optical drive has been completely disassembled, and the assembly begins.
8.The four screws are aligned and the optical drive is put back into the iron case.
9.Press down on the back case.
10.Press the front panel back.
11.Finally, install the bottom cover and put on the screws to finish.
-
Anonymous users2024-02-05Open the covers on both sides of the case, and the place opposite the optical drive is usually locked with two or four screws, unscrewed, and then pushed out from the back.
-
Anonymous users2024-02-04Open the case, unplug the cable to ***, and loosen the side screws again.
-
Anonymous users2024-02-03Generally, the bezel is removed first, and then the optical drive is pushed out. Of course, different chassis may be different.
-
Anonymous users2024-02-02Generally, the side screws can be removed and pushed out of the main unit. Some have to remove the front cover.
-
Anonymous users2024-02-01Open the case cover on the left, and there are several screws in the upper right corner, all of which can be unscrewed and removed directly.
-
Anonymous users2024-01-31The power supply, the data cable is removed. Remove the screws fixed on the left and right sides.
Pull out of the chassis.
-
Anonymous users2024-01-30First, dial the cable on the optical drive, and push it forward from the back to get it down.
-
Anonymous users2024-01-29The K550V's optical drive is thick, and it is risky to disassemble the device by yourself, so in order to avoid damage to the laptop, it is recommended that you bring the machine to your local ASUS repair center to disassemble the machine.
It tastes great and is excellent on a first-class basis! The entrance is crispy and fragrant, so you can try it! >>>More
The prospect is good, the future development trend, the most ideal clean energy! Electric energy can not be stored in energy, electricity is an indispensable energy in life, only a steady stream of power generation, in order to the normal operation of the society! Compared with hydropower, thermal power, wind power, and nuclear power, solar photovoltaic power is the most ideal clean energy. >>>More
Method 1 Use the PN junction of the digital multimeter to measure the end, the red pen "battery + pole" is connected to the "1" end of the optocoupler, and the black pen "battery-pole" is connected to the "2" end of the optocoupler (even if the light-emitting diode of the optocoupler is positively conducted), use another meter to measure the resistance of the "3" and "4" terminals, disconnect or turn on the input terminal (light-emitting diode end), and the resistance of the output end should change significantly, indicating that it is good to change the optocoupler. In addition, the multimeter at the LED end can be replaced by a battery string current-limiting resistor. Method 2 The judgment method of optocoupler PC817 is to detect the light-emitting end of the optocoupler with the diode file of the multimeter, and then add a voltage of about five volts to the light-emitting end to judge the quality of the triode end Method 3 Place the multimeter in the R*100O block, and connect the black meter pen to the 1 end and the red pen to the 2 ends, the resistance is generally 5K -8K, and this value is the forward resistance of the light-emitting diode. >>>More
There are two kinds of indoor portraits, one is on-site light photography, which is to use the light of the scene as the only light source to shoot images, such as: the light projected by the window, candlelight, fireplace firelight, etc., this kind of photography is generally that you arrange the subject in the brightest light, you measure the brightest light, and the details of the dark part are left alone, this kind of photography can show a sense of realism. >>>More
Recently, international oil prices have maintained a weak trend, and photovoltaics, as an important alternative energy source, have also been hit hard, and the stock prices of related companies have risen from the highest level in the past year** by more than 80%. Analysts pointed out that due to the temporary loss of the substitution advantage of photovoltaic products due to low oil prices, and Obama's new will not have much impact in the short term, it is reasonable for the stock price of photovoltaic companies to suffer. >>>More