On the issue of hot stamping, how to burn hot on clothes

Here's how to put a hot stamping on clothes:

Tools to prepare: clothes, steam iron, stickers.

Specific steps: 1. Wash and dry first, and do shrinkage treatment, otherwise it will seriously affect the effect of hot press. Lay the clothes flat, iron them flat, put them on the hot stamp, and cover them with a thin cotton cloth.

Turn the iron to the "cotton" setting, turn off the steam iron, and press for 10-15 seconds. If the heat is large, make sure that each position of the heat is ironed.

2. Slowly peel off the transparent surface film while it is hot. Turn the garment over to the reverse side and iron it again in the hot press position. Inspect all parts of the hot stamp, especially the edges, and iron them in time if there is any problem.

Notes:

It is necessary to pay attention to the fact that the clothes must be washed first and then ironed, and the ironing must be pressed hard when ironing, and if you are bored, you can ask your husband to help. It can be washed after 24 hours after blanching. Machine-washed clothes should be turned over and washed, and hand washing should be done as much as possible without rubbing the painting.

Do not expose to the sun, turn it over to dry.

The reason for the opening of the glue is that the temperature is too high. (The temperature is too high, and the glue powder for hot stamping is oversolvent, and the condensation time becomes longer, so when it is torn, it still sticks to the film and is not fixed to the clothes). The temperature is too low (the temperature is too low, the rubber powder is not dissolved, and there is no way to paste it) The appropriate temperature:

Cotton stalls. The bottom plate is too soft (you can use a large magazine, and it is more appropriate to add two layers of towels to make the floor) The pressure is not enough, and there is no force to press down during the hot process, and the rubber powder does not dissolve into the cloth.

The 3 basic elements of heat stamping are: temperature, pressure, and hot stamping time. In order to obtain the ideal hot stamping effect, the process parameters such as hot stamping temperature, hot stamping pressure, and hot stamping speed must be reasonably mastered; In addition, the quality of the raw materials related to the heat transfer must also be guaranteed, such as:

The hot stamping adaptability of the substrate, the performance of the hot stamping paper material and the quality of the hot stamping plate, etc. If there is a problem with a certain link, it will affect the final hot stamping effect.

The quality of hot stamping is affected by a variety of factors, especially because the hot stamping is carried out after printing, and its printing effect, the thickness of the ink layer, the nature of the ink, etc., will directly affect the hot stamping effect. Therefore, the following issues should be noted:

1) The ink should be dried before hot stamping. If the ink layer is not yet dry and the hot stamping begins, due to the poor adhesion of the ink, it is easy to cause the failure of pulling off the ink layer, so that the hot stamping cannot be done.

2) If the hot stamping on the background color, the ink layer of the background color should not be too thick or too thick, and the heat transfer machine should try to achieve deep ink and thin printing, and avoid 3-color and 4-color overprinting, so as not to cause undesirable phenomena such as poor hot stamping, paste, and even pulling off the ink layer due to the ink layer being too thick. In addition, when the background color of the hot stamping is stamped, the hot stamping temperature should be appropriately reduced, so that the hot stamping effect is more ideal.

3) If the hot stamping on the spot color on the ground, it is necessary to control the amount of ink additives when printing the spot color, for example, too much desiccant will cause the crystallization of the ink layer, resulting in the hot stamping of anodized aluminum; In addition, when printing, we should try to avoid mixing non-drying oils, such as engine oil, kerosene, etc.

<>1.According to the characteristics of different fabrics of customers to provide accurate temperature, time, pressure of the three elements of ironing, ordinary fabrics for 150 degrees, the scalding time is 8 seconds, the scalding pressure is determined according to the equipment used by customers, the scalding time of leather fabrics is 120 degrees, 8 seconds, the washing mark ironing temperature is 135 degrees, the time is 8 seconds, the B-class hot heating temperature is 140 degrees, the time is 8 seconds, the scalding temperature of small area of the pattern is 130-140 degrees, should not exceed 150 degrees, Large area patterns can be set to 150 degrees for scalding.

2.When it is ironed, the pattern should be cut off, placed on the clothes and then torn off after being ironed at high temperatures.

3.In order to prevent the heating plate from coming into direct contact with the fabric and avoid the phenomenon of whitishing after the dark fabric is ironed, it is recommended that customers put a breathable cotton cloth on the heating plate before scalding.

Cut the heat stroke, and adjust the thermostat and timer of the heat stroke machine. Place the garment on the silicone board, then place the hot stamping flat on the garment, and press down firmly on the handle to close it completely. When the heat transfer buzzer sounds, bring the handle back to its original position.

If it is a cold tear, after it cools, tear off the heat transfer paper, and if it is a hot tear, immediately tear off the heat transfer paper. <

1. Cut the heat stroke, and adjust the thermostat and timer of the heat stroke machine.

2. Put the clothes on the silicone board, then put the hot stamping flat on the clothes, and press down the handle to close it completely.

3. When the buzzer of the heat transfer machine sounds, lift the handle back to its original position.

4. If it is a cold tear, after cooling, tear off the heat transfer paper, if it is a hot tear, you need to tear off the heat transfer paper immediately.