How many tiles can be pasted with one kilogram of tile adhesive

Nowadays, the adhesive of Chenguang liquid, which is very popular with construction and decoration companies, can be brushed for about 10-13 kg with 1kg.

How to use:1: If you want to renovate the surface of an old wall before painting or on an old wall, simply roll it with a short-bristled roller.

2: Before pasting tiles: about half an hour in advance, stir the binder evenly with a brown brush or a small roller, and directly brush it on the back of the tile (about 5mm can be left along the perimeter of the brick to prevent the binder from flowing to the front), and after the surface is transparent, add about one-third of the fine sand with 425 cement and stir it into a mortar paste.

It is also recommended to paint the adhesive on the wall, so that the adhesion is stronger, the waterproof effect is better, and it is absolutely not hollow and does not fall off.

3: Material dosage: This product does not need to add water, it can be used directly after opening the barrel, and the surface layer is single, and each kilogram of binder can be painted with 10-13 square meters.

4: The best construction temperature 5, the actual painting area will vary depending on the construction method, surface smoothness and construction environment.

It should be said how much adhesive is needed to paste a square meter of tiles. Generally, it is calculated according to the specific gravity of the material, the cement slurry paste is generally 3-5 kg, and the adhesive is generally about 6 kg.

I have used Beijing Lynes tile adhesive, which is said to be a bag of 5 square meters.

I don't know if it's the same thing as the face brick binder you said?

3 to 7 square meters with the common 20kg packaging of JCDecaux tile adhesive, a bag of tile adhesive can be pasted 3 to 7 square meters. There are two main factors influencing the amount of tile adhesive: the flatness of the base surface and the applicator used.

The flatter the base, the less it will be used. The toothed scraper is the best tool for tile adhesive construction, and the smaller the tooth opening, the smaller the dosage.

It can be applied between 4 and 5 squares.

The dosage is mainly determined according to the thickness of the application, if the coating is 1 mm, the tile adhesive used per square tile is kilograms, if it reaches 3 mm, the tile adhesive needs to reach or kilograms, if the thickness of the coating reaches 6 mm, the tile adhesive used is 9 to kilograms. Of course, this is also a theoretical value, if you prepare 20 kg of tile adhesive, the thickness of the application is 3 mm, and the area that can be applied is between 4 square and 5 square meters.

Precautions for tiling.

1. When pasting tiles, you should first pay attention to soaking the tiles in water before pasting them.

2. When pasting tiles, the cement needs to be put a little more, so that it will stick more firmly.

3. When pasting tiles, you also need to pay attention to the parallelism of the tiles, otherwise it will affect the overall aesthetic effect of the room.

4. When pasting tiles, you also need to pay attention to choosing a more experienced master, so that the tiles will look better.

5. It is also very important for the owner to choose the quality of the tile, which will affect the service life of the tile in the later stage.

The above content refers to Encyclopedia - Adhesives.

People's Daily Online-How to choose glue for tiles?

A bag of tile adhesive has 40 pounds. The packaging of tile adhesive is generally 20 to 25 kg per bag, ** generally divided according to the model.

Ordinary binders are also relatively cheap and practical, and are used in most construction sites. Its operation method is simple and convenient, the tiles do not need to be soaked in wet when using, and the walls should not be wet with water. It has good flexibility and impermeability, and the most important thing is that the ordinary binder can also resist cracking and aging.

Let the construction staff have a good non-toxic environment.

There is another type called polymer type, and the polymer type has many advantages, such as strong adhesion and good water resistance. At the same time, it is very durable, and can be used as an adhesive for the interface in some cases. It is also very time-saving to construct, and the surface is also beautiful.

Heavy brick binder, which is also the last one, its function is to professionally solve the problem that general adhesives cannot be attached. The heavy brick binder to make up for the lack of general binders, especially on the outside of the tile, can also be glued up a layer, which is a good solution to the problem that some adhesives cannot be adhered to. At the same time, there is no need to eradicate the original tiles in the paste, which brings great convenience to the construction personnel.

The thickness of the tile adhesive is 5-10mm. The material is made of cement, quartz sand, polymer cementitious material with a variety of additives through mechanical mixing.

Its main function is to have the effect of dispersion and air entrainment when the bonded mortar is in a freshly mixed state, so it can improve the workability of the mortar; The water retention of the mortar is enhanced, so that the cement can be hydrated for a long time, and the mortar obtains higher strength due to more adequate hydration formation; In addition, after dispersion, the rubber powder forms a film and plays a reinforcing role as a second adhesive, which is distributed in the whole mortar system as a reinforcing material, thus increasing the cohesion of the mortar; And it can bridge the shrinkage cracks, which plays a good sealing role.

This ensures that even smooth tiles with a fully vitrified surface can be firmly bonded to the substrate without hollowing. And add flocculent to the product, so that it can make the mortar have better elasticity and flexibility, so as to ensure that the product can be fully applied to the elevator hall and high-rise building exterior wall marble and tile paste.

There are three main construction methods of Chenguang tile adhesive - back adhesive method, trowel method and combination method 1The back-adhesive method involves applying a tile adhesive to the back of the tile and then applying it to the base layer. At present, most of the tile adhesives use this method, because this is the traditional ceramic tile adhesive method.

The thickness of the tile adhesive layer is about 5-10mm.

2.The trowel method refers to scraping the tile adhesive batch to the surface of the base layer to be tiled with a toothed spatula in advance, and then combing it with a toothed spatula to form a mortar layer with raised stripes and uniform thickness, and then pressing the tile on top of it and twisting slightly, the thickness of the tile adhesive layer is about 2-4mm.

3.The combination method refers to the combination of the back adhesive method and the trowel method, that is, the tile adhesive is scraped to the surface of the base layer to be pasted with the trowel method to form a mortar layer with raised stripes and uniform thickness, and then a layer of tile adhesive is also applied on the back of the tile, and then the tile is pasted on the base layer wet, and the thickness of the tile adhesive layer is about 3-5mm.

First of all, we need to look at the flatness of the base surface. If the flatness of the base surface is about plus or minus 5 mm, the thickness of the binder is controlled at about centimeters, and if the flatness of the base surface is about plus or minus 10 mm, the thickness of the binder is controlled at about centimeters. It should be noted that the thickness of a single construction should not exceed the thickness of centimeters as much as possible.

Construction method. Mixing ratio: water:powder = 1:4 (kg).

1 Pour water into the container, then add the tile adhesive in proportion, stir it into a uniform, non-granular paste with electric stirring, let it stand for 5 minutes and stir for 1-2 minutes.

2 Use a toothed scraper to apply the tile glue to the base surface. Make it evenly distributed, and form a strip of teeth, apply about 1 at a time, and then knead the tile on it.

3 If the groove on the back of the tile is deep, in addition to applying tile adhesive on the working surface, the adhesive should also be applied on the back of the tile.

Precautions. 1: This product is suitable for construction in the environment of 5 -40, and the vertical and flatness of the base surface should be confirmed before construction.

2: It is best to use up the tile adhesive that has been stirred with water within 2 hours, and do not mix and stir the tile adhesive that has been dried and solidified, 3: 24 hours after the construction is completed, you can step into or fill the joint.

4: Stir well with an electric mixer. The specific gravity of water should not exceed 25%.

5: No cement, sand and other substances can be added, only water can be added to stir.

6: The thickness of batch scraping is controlled at about centimeters each time.

The standard construction thickness of tile adhesive is 3 5mm thin paste tile, on the leveled base surface, ceramic tile with a maximum side length of 10cm (mosaic) ceramic tile, with a suitable toothed spatula to ensure that the thickness of the glue layer is 2mm. For ceramic tiles with a maximum side length of 10cm and a maximum side length of 30cm, use a suitable toothed spatula to ensure that the thickness of the adhesive layer gradually increases from 2mm to a flat base surface, and ceramic tiles with a ceramic tile specification of 30cm and a maximum side length of 60cm need to use a suitable toothed spatula to ensure that the thickness of the adhesive layer gradually increases from 4mm to 6mm, and then use a spatula flat mouth on the back of the ceramic tile to layer a thin layer of adhesive ("combination method"), and finally pave the ceramic tiles in place. When using a spatula flat thin batch of adhesive, the thickness should be less than 1mm, but the full batch should be made without leaving gaps.

There is no substantial difference between the adhesive used for tiling tiles and cement mortar, and the thickness of the adhesive used for paving the wall should be between 1 2 cm.

The thickness of wall tile paste is generally 3-5mm. The specific steps are, first use the trowel method to scrape the tile adhesive batch to the surface of the base layer to be tiled to form a mortar layer with raised stripes and uniform thickness, and then apply a thin layer of tile adhesive on the back of the tile, and then paste the tile on the base layer when wet. Hope it helps.

The thickness of tile adhesive is directly affected by the size of the tile, in the case of a flat base, the larger the tile, the thicker the tile adhesive will be.

Now there are two specifications of toothed scraper with 6*6mm and 10*10mm for scraping tile adhesive, so the former generally needs tile adhesive per square meter, and the latter needs about 5kg tile adhesive per square meter.

The adhesive of the building solid tile is easy to use, and the tiles do not fall off the bricks.

Summary. As far as I know, different companies have different ** for tile adhesives, the specific ** is as follows:

1. Beijing Xinsheng Hi-Tech Building Decoration Project, 830 yuan ton.

2. Nanchang Qingshanhu District Shunhui Building Materials Waterproof Material Factory, **725 yuan ton.

3. Beijing Rongchuan Yuda ******, **950 yuan ton.

How much does tile adhesive cost.

Hello. Please wait a moment Checking for you.

How much is a ton of tile adhesive.

Please wait. As far as I know, different companies have different views on ceramic tile adhesives, as follows: 1. Heng crack Beijing Xinsheng Gao Jing Zhengke Building Decoration Project, 830 yuan tons 2, Nanchang Qingshanhu District Shunhui Building Materials Waterproof Material Factory, 725 yuan tons 3, Beijing Rongchuan Yuda ******, 950 yuan tons or more in the network, for reference only, the specific details are subject to the actual Liang Regret**.

Tile adhesive is a kind of cement, quartz sand, polymer cementing material with a variety of additives through mechanical mixing and homogeneous, which has the characteristics of high joint strength, convenient construction, fast hardening speed, water resistance, alkali resistance and weather resistance, etc., mainly used in the pasting of ceramic tiles and face tiles.

However, when using tile adhesive, it should be noted that the dust on the ground should be cleaned up first to avoid affecting the use of ceramic tile adhesive.

The above is my understanding and conclusion of the above questions of Ruhe, I hope mine can help you and wish you a happy life

Kiss! Hello, happy to answer your <>

Pro-tile thin paste 60 square needs 12-15 kg of tile adhesive wheel which tile, also known as tile, is a refractory metal oxide and semi-metal oxide, through the process of grinding, mixing, pressing, glazing, sintering, and forming an acid and alkali resistant porcelain or stone, building or decorative materials, called ceramic tiles. Its raw materials are mostly made of clay, quartz sand, etc., which are mixed with tung burning, and have high hardness. It is mostly used for the beautification of the wall, and the cement is used to bond to the wall.

National classification standard: porcelain tile water absorption rate less than or equal to; The water absorption rate of stoneware is greater than or less than or equal to 3%; The water absorption rate of fine stoneware is greater than 3% and less than or equal to 6%; Stoneware brick water absorption rate greater than 6%, less than or equal to 10%; The water absorption rate of ceramic bricks is greater than 10%. Water Absorption Expression:

10% 6% 3% porcelain tiles. Water absorption is summarized as semi-porcelain, I hope mine can help you <>

Do you have any other questions?