Car wipers won t move? What s going on with the car wipers not moving

1.Refer to the manual to find out what type of wiper you are using.

2.Pay attention to whether the pole is connected to the wiper rocker arm in the correct way. Some of the arms are screwed to the rocker arm, while others are locked with a buckle.

3.Pull the wiper up and touch it with your fingers to check if there is any damage on the cleaned rubber wiper and the elasticity of the rubber blades. If the blades are aged, hardened, or cracked, then the wiper is broken.

4.During the test, the wiper switch is placed at various speed positions to check whether the wiper maintains a certain speed at different speeds. Especially in the intermittent working state, it is also necessary to pay attention to whether the wiper maintains a certain speed when it is in motion.

5.Check the wiper status and whether the wiper rod has uneven swing or leakage. If the following three situations occur, this wiper is not qualified:

First, the swing is not smooth, and the wiper is not beating normally;

Second, the contact surface of the rubber and the glass surface cannot be completely fitted, resulting in wiping residue;

Third, after wiping, the glass surface presents a water film state, and fine stripes, fog and linear residues are produced on the glass.

6.During the test, attention should be paid to whether there is abnormal noise in the motor, especially when the wiper motor "hums" and does not rotate. This indicates that the mechanical transmission part of the wiper is rusted or stuck, and the wiper switch should be turned off immediately to prevent the motor from being burned.

7.Some people believe that the longer the wiper blade, the larger the brush area, and the better the visibility. In fact, wiper blades are not always better.

Although lengthening the length of the wiper blades can increase the visible range, it will also increase the burden on the wiper motor and wiper rod. Of course, it is possible to lengthen it, but it must be guaranteed that it must not interfere with the normal operation of the wipers.

1. Open the guide cover to observe whether the transmission connecting rod is dislocated (this reason is the most common).

2. Check whether the fuse is in good condition.

3. Disassemble the motor cord plug to turn on the power supply, and measure whether there is voltage with a multimeter.

4. If the fuse is intact and the motor has no voltage, check whether the circuit and direction light combination switch are in good condition.

5. Generally, the motor will burn out.

6. If you turn on the power supply and measure the normal voltage at the wiper motor, you can consider that the motor is broken.

Check that the fuse is energized.

Generally, family car wipers are equipped with standard, fast and slow three gears, which can be adjusted, generally on the right side of the steering wheel. There may be some differences between models.

The manual wiper adjustment method is as follows:

Light rainfall: Don't rush to use wipers when it starts to rain lightly. Spray glass water to moisten the glass before opening it for the first time to avoid dry scraping of the glass window due to lack of moisture.

Heavy rainfall: If the rain is heavy, adjust the working frequency of the wiper in time to ensure a clear vision. If the rain is too heavy and the rain is too urgent, and you still can't see clearly when you drive to the highest gear, it is recommended to find a safe place to stop temporarily and wait for the rain to lighten, and remember to turn on the fog lights and double flashes when parking on the side of the road to avoid accidents.

Use rear window wipers: If your car has a rear wiper, don't forget to turn it on when it rains.

Generally, SUVs, hatchbacks, MPVs and other models are mostly equipped with rear wipers, this is because the rear windshield of the sedan has air flow through, while the hatchback or SUV does not, which leads to the fact that once there is rain, the sedan can use the air flow to blow down the water droplets, but the hatchback cannot, the water can not be blown off in time, it will be easy to stick to the dust, affect the sight of the rearview mirror, and lead to unsafe driving.

Hope, thank you.

If it is a cold area such as the Northeast, check whether it is frozen, otherwise it may be that the wiper motor is damaged, if it is frozen, the wiper can not be forcibly started, otherwise it will burn out the wiper motor, and it should be thawed in a warm way before it can be used.

Second, check that the joystick is properly attached to the wiper rocker. Because some arms are screwed to the wide core of the rocker arm, while others are locked with a convex buckle.

There are several reasons why the wipers of a car do not move:

1. It may be that the connector of the motor is not connected properly, and the lower line needs to be reconnected before it can be used.

2. Turn the wiper to the largest gear and gently dial it with your hand to see if it can rotate, if it can rotate, it can be rusted on the induction of the wiper, and you can clean it directly.

3. Check whether the safety of the wiper is intact and whether the fuse is burned out, and then check whether the electric rubber machine is burned out, whether the connecting rod is slipped, or whether the combination switch is in poor contact.

Photo by Tang Yanyan of Pacific Automobile Network).

What's going on with the car wiper not moving The car wiper is broken. If it is in a cold region such as the Tohoku, check if there is any freezing first. Otherwise, the wiper motor may be damaged.

If it freezes, you can't force the wiper to start, otherwise it will burn out the wiper motor. It should be thawed with warm water before use. Second, check that the joystick is connected to the wiper rocker arm in the correct way.

Because some arms are fixed to the rocker arm with screws, and some are locked with a convex buckle. There are several reasons why car wipers don't work:1

It is possible that the connector of the motor is not well connected and needs to be reconnected to the line before it can be used. 2.Turn the wipers to the highest setting and gently stir with your hands to see if they turn.

If it can be rotated, it means that the sensor of the wiper is rusty and can be cleaned directly. 3.Check whether the fuse of the wiper is intact, whether the fuse is blown out, and then check whether the motor is blown out, whether the connecting rod is slipped, or whether the combination switch is in poor contact, etc.

The possible reasons why the car wiper does not move are: the wiper slippery fuse is blown and the wiper motor is burned out, and the messenger leather wiper switch is damaged. You can go to the nearby repair shop to check the cause and troubleshoot.

The following is a specific introduction: 1. Introduction to the exclusion method of the automobile wiper immobility: the automobile wiper may not move because the fuse (to prevent circuit overload) is blown and the wiper cannot work normally, then the fuse box should be opened to check whether the corresponding fuse is blown or not.

2. Precautions for replacing the fuse: Before replacing the fuse, be sure to close all the electric doors of the car. It is also necessary to consider that the probability of motor burnout is very low, but it may also be a problem with quality control.

The solution to the wiper not moving is as follows1. Check the joints of the motor and whether you need to reconnect the lower line.

2. Turn the wiper to the largest gear and gently toggle it with your hand to observe whether the wiper can rotate, if it can rotate, it means that the inductor of the wiper is rusty, and you can clean it directly.

3. Check whether the safety of the wiper is in good condition, whether the fuse is burned out, whether the motor is burned out, whether the connecting rod is slipped, or whether the combination switch is in poor contact. In daily use, it should be noted that do not let the wiper dry and scrape the glass, if the wiper strip is aged and hardened, or the windshield is attached to the mud and sand foreign matter, the wiper is easy to scratch the glass, causing irreparable damage.

The failure of the wiper may be caused by these four points: 1. The wiper insurance fuse, the user can replace it by himself, ** the fuse box sticker, find the number of insurance, pull out the old insurance and replace it with the prescribed fuse current flow insurance; 2. The wiper switch is damaged; 3. The wire plug is loose or has poor contact due to rust; 4. The wiper motor is damaged or the motor is poorly grounded; 5. Connecting rod mechanism, turn.

The solutions for the car wiper not moving are: removing foreign objects, replacing the motor, replacing the control lever, and replacing the fuse.

1. Remove foreign bodies

In the process of using the car, if the wiper suddenly does not move, the first thing you need to check is whether there are some foreign objects such as mud and sand stuck at the position of the wiper, and these foreign objects only need to be cleaned up, so the wiper can resume work.

2. Replace the motor

If the motor fails, the wiper does not move, it may be that the motor of the wiper is faulty, in this case, you need to go to the circuit maintenance center in time, and the professional maintenance personnel can check out the specific fault, and then repair it in a targeted manner.

3. Replace the joystick

If the lever fails, the wiper lever of the vehicle is more prone to problems, and in general, the owner can directly buy a new lever online to replace, or go to the auto repair shop to replace it.

4. Replace the fuse

The fuse is burned, if the fuse of the wiper is overloaded, it is easy to cause it to be blown out, so that the wiper will not move, in this case, the owner can check the fuse by himself, and replace it in time if it is burned.

What wipers do:

Equipment used to scrape rain and dust attached to the windshield of vehicles to improve the visibility of drivers and increase driving safety. Because of the legal requirements, cars in almost all places carry windshield wipers. Vehicles such as hatchbacks and minivans are also equipped with wipers in the rear windows.

In addition to automobiles, windshield wipers are also installed in other means of transportation, such as trains and trams.

Some construction equipment, such as cranes, are also equipped with wipers. There are roughly two types of wipers, one is the traditional intermittent type, which is the most common wiper, with three to four sections, which are adjusted by the driver according to the rain and line of sight, and the other is the raindrop sensing type, which has been mostly used in medium and high-end models in recent years.