I want to fix it, my phone is always in the boot interface, can t get in?

In this case, it should be that the system is abnormal, the landlord can restore the factory settings first, and if it doesn't work, flash the phone again, so that the phone can return to normal, as long as it is not a hardware problem, then it can be solved.

If you can't enter the boot interface all the time, you can consider upgrading the mobile phone system, and it won't appear after the general system upgrade.

If you can't get in, it may be because all aspects of the authority have been turned off, or the problem of some boot buttons corresponding to the mobile phone, then in this case, you can go to the mobile phone repair shop to repair the corresponding lines and the status of all aspects.

Hello, there is no good way, it is recommended that you take the machine and go directly to the official maintenance department.

The reason why the phone stays on the boot interface and does not move: the main reason is that the system is unstable and the compatibility is not good when upgrading or flashing, resulting in system crash or boot file corruption.

Workaround:1Factory reset.

2.In the power-off state, press and hold the volume down button + power on button at the same time.

3.The boot interface appears, release it, and enter the recovery flash tool for a while.

4.Through the volume up and down, select wipe data, OK (the volume button is up and down, the power button is OK), the options appear, and yes.

5.After returning to the menu automatically, click Wipe Cache until it automatically returns to the main menu.

6.Select reboot and reboot is good to go.

You can restore the factory settings and try it, but if it doesn't work, change your phone.

If you can't get into the boot interface of the mobile phone, it is recommended to go to the local mobile phone repair center and repair it, and generally those people will check and repair it.

If you are using a vivo mobile phone and the device cannot be turned on, observe the device fault phenomenon and troubleshoot it according to the corresponding methods below:

Scenario 1: The screen does not turn on when the device is turned on, and the device does not vibrate or react.

Check whether the battery is sufficient, charge the device for more than half an hour, and try to turn it on again;

Force restart the device to try to resume use here:

Tablet, FunTouch OS and subsequent models: Press and hold the "Power button" + "Volume Down button" at the same time for more than 10 seconds;

Press and hold the top round button for more than 10 seconds to force restart the phone (applicable to NEX 3 NEX 3S);

FunTouch OS previous models: Press and hold the "Power Button" for more than 12 seconds.

If the device is stuck, damaged, or liquid, please bring the device to the official vivo service center for further maintenance.

Scenario 2: When the device is powered on or forced to restart, the screen does not display.

If the device vibrates, but the screen is still black, it is more likely that the screen is faulty, please bring the device to the vivo official service center for further maintenance.

Scenario 3: When the computer is turned on, the screen is displayed and cannot enter the desktop.

Force restart the device to try to resume use, how to do it:

1. Tablet, FunTouch OS and subsequent system models: Press and hold the "Power Button" + "Volume Down Button" for more than 10 seconds at the same time;

2. Press and hold the top button for more than 10 seconds to force restart the phone (applicable to NEX 3 NEX 3S);

3. FunTouch OS previous models: Press and hold the "Power Button" for more than 12 seconds.

Try to repair the system through the "System Repair Mode".

Operation method: Step 1: When the phone is turned off or restarted, press and hold the "Power Button" and "Volume Up Button" at the same time before the screen turns on for 3 10 seconds, until the screen displays the word "fastboot" and then release the button, press "Volume-" to move the cursor to "Enter Recovery".

Step 2: Find [Install System Software" > Network Update Latest Version**Latest Version > Connect to Available WiFi >>> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >

<> folding screen: When the device is turned off, press and hold the "Power Button" and "Volume +" for about 5 seconds to enter fastboot mode.

NEX 3 NEX 3S: Press and hold the top round button for about a second in the shutdown state, and then press and hold "Volume +" to enter fastboot mode. Rolling oak.

If the above methods fail to help recover, it is recommended to call the customer service center in advance to confirm the relevant matters and understand the working time, so as not to delay precious time.

If the mobile phone is not used for a long time, it will not be able to turn on, then the big dust is generally the battery to ask the rolling question to charge first, if it is into the water or fall and do not turn on, then there is a disassembly to go into the brother hole.

If the mobile phone cannot enter the system page after booting up, and the screen is stuck or frozen, it is recommended to:

1.Please press and hold the power button and the down volume button at the same time for more than 7 seconds to restart the device; If it is a mobile phone with a removable battery, please press and hold the power button for 8-10 seconds to restart the machine, if it does not work, please turn off the battery and reinsert it.

2.If the problem persists after restarting the machine, it is recommended that you bring the purchase receipt, repair card, and machine to the Samsung service center for inspection.

There are many factors that the mobile phone cannot be turned on, and the battery, mobile phone software, and hardware will cause this kind of failure to turn on. We recommend trying the following:

1. Replace a mobile phone battery of the same model for testing or send the battery to the nearest service center for testing.

2. Take out the battery, clean the metal contacts of the battery with a rubber and test.

3. Take out the SIM card and SD card at the same time, and then press the power button for more than 10 seconds to test whether it can be turned on.

If it still can't be turned on, there may be a problem with the system program or hardware, it is recommended to send the phone to the nearest Samsung service center for testing.

No need to flash, as long as your mobile phone hardware is fine, can't turn on that is a problem with the system, you just need to grid the machine, but the grid machine is divided into soft grid and hard grid, you want to be hard, check your mobile phone grid on the Internet, and then do it, I have also had this situation.

First of all, you must be clear about why your phone does not turn on.

There are two kinds of problems with the phone not turning on: hardware or software, and system. If there is an external force, such as being dropped, pressed, flooded, overheated, etc., it must be a hardware problem.

If you have some software, delete some system files, or can't boot after flashing, this is generally a software or system problem. Understand the problem** problem and solve it. There are two situations in which the phone does not turn on, and the solutions are as follows.

The phone is on and responds but can't be turned on normally:

This is the most common situation where your phone won't turn on. When the phone is turned on, there is a vibration and sound, but the screen is dark; After the mobile phone is turned on, it has been stuck in the logo interface and cannot enter the operation interface; There is also the fact that the mobile phone can enter the normal interface but there is no response when you click on anything, etc., which is the most common manifestation of abnormal boot.

First things first: check your phone's battery. The reaction when the phone is turned on proves that the battery is still working, and in addition to the aging of the battery and water ingress, the battery problem can be ruled out.

If the battery is aging, you can try it with the same type of battery, and if it can be turned on normally, then replace it with a battery; If it is water, turn on the device when the water has not yet dried, it will cause a short circuit in the battery, and the phone will only run for a while, and the battery will be damaged due to a short circuit, you can wait for a day or two for the phone to completely dry and change the battery.

Then: check your phone screen. Under the destruction of external forces, the screen fails, especially some mobile phones themselves are soldered, which is particularly prone to "fake not booting" caused by the screen.

Although only a slight fall, but the mobile phone screen is no longer responsive due to the disconnection of the line, at this time you can tap the phone, a few more shots, if the mobile phone screen will flash from time to time, this proves that the mobile phone is only a certain line of problems, you can disassemble the machine after finding the disconnected solder joint to re-weld, or go to the repair point for repair. Especially when the phone vibrates and sounds normally when it is turned on, but the screen does not respond. This is especially the case for consideration.

Again: Check if you can enter recovery, consider flashing. Both of the above are hardware problems, but the phone can't be turned on completely normally, because there are many software or system problems.

If the phone is just stuck in the logo screen or can not be operated when booted into the interface, then check whether the phone can enter recovery, press and hold the power button + volume down key, if the phone enters the following screen, and can move the cursor by moving the volume + and - keys of the mobile phone, then the phone can be solved by flashing.

Causes of bricking.

There are many reasons for flashing failure, and here are a few common ones:

1. The most common is to unplug the mobile phone data cable prematurely. When flashing the computer with a computer, many people will pull out the data cable in a hurry, and this will lead to serious consequences. In addition, poor contact of the data cable can also lead to this consequence.

When flashing, you must be calm, and ensure that you are connected, do not pull out the data cable at will, and generally wait until the computer prompts you to complete the unplugging.

2. The wrong firmware has been written. Generally, the firmware of different models cannot be flashed with each other, and licensed goods and parallel goods cannot be flashed with each other. In addition, the configuration of mobile phones in different regions is also different, and the firmware is different.

When flashing, be sure to select the firmware for flashing according to the model of the phone and the original sales region.

3. The lack of battery of the mobile phone will also cause the flashing process to be interrupted and the flashing process will fail.

The solution to bricking.

1. Generally, you can try to use a variety of the same and different flashing software to flash the firmware again.

2. Sometimes there will be a phenomenon of fake bricks, you can try the grid machine.

3. Don't panic when you really can't solve it. Most mobile phone repair shops can provide professional flashing tools for flashing services, and the fee is generally only tens of yuan, which can solve the problem of bricking. It's also okay when the phone is still in warranty.

Try to send it to customer service to brush, but it can't be said to be caused by flashing, otherwise it will be regarded as a human failure. If you can't brush it for free, then it's better to send it to the repair shop, the customer service charge is very expensive, and the repair shop does not have a big gap in technology, as long as you are careful to see that the battery has not been adjusted.