Why do you plaster the wall first and then paste the bricks instead of the bricks directly?

As we all know, cement mortar is generally used for tiling, but in recent years, there have been more tile adhesives on the market, and I don't know which one is better to use!

Let's look at the cement mortar first, that is, it is mainly cement, add yellow sand and some waterproof additives, and then stir with water, which is basically zero pollution, high adhesion, and preferential treatment.

But the bad thing is that cement mortar is affected by many external factors and is easy to fall off. In addition, the hardness of tiles on the market is getting higher and higher, and the focus is on poor water absorption, so the tiles often fall off.

From the appearance, tile adhesive and cement are almost the same, mainly mixed with water, and then directly used to paste tiles. However, tile adhesive has an advantage that cement does not have, that is, it is less affected by external factors, and it is resistant to low temperature and water. The bad point may be that it is expensive, and there are many bad tile adhesives on the market, and there may even be the problem of excessive formaldehyde.

Compared with cement and tile adhesive, the adhesive performance of ceramic tile adhesive will be better, the point is that you don't need to run the tile in advance, you can paste it directly. There is no need to paint a thick layer on the wall, and it is basically very firm when pasted on.

Of course, good things are generally expensive, so there is no need to use tile adhesive in all places, you can use it in the kitchen and bathroom, because these places are often wet, and it is easy to fall off with general cement.

If you put tiles, you need to have concave and convex points on the wall, so that the bricks can use the friction with the wall to stick to the wall, otherwise it is easy to fall off.

First plastering plays a leveling role, that is, a leveling layer, I think.

Do new brick walls still need to be plastered? Wall plastering is an indispensable part of house decoration. It is the base material for residential wall decoration. It covers the stone bricks on the walls with cement mortar for better putty powder and stucco of the walls.

1. Wall plastering**.

1。According to the different interior and exterior walls, the ** of wall plastering varies greatly. Usually, the ** of exterior wall plastering is about three times that of interior wall plastering.

Due to the small construction area of exterior wall plastering, there are certain safety risks, and scaffolding is also required, which greatly increases the cost. Usually, the labor cost of interior wall plastering is about 10 to 12 yuan per square meter of interior wall plastering, and 20-24 yuan per square meter of outdoor plastering**. The final ** is mainly determined according to the local consumption level and the quality of construction.

2。Usually, home renovation is as simple as painting the interior walls. Do new brick walls still need to be plastered?

Under normal circumstances, the ** of contracted labor and materials is between 12-23 yuan. If the cost of the material is self-sufficient, then as long as the workers are invited to the construction, it is relatively cheap, and the market is usually about 10 yuan.

2. Precautions for wall plastering.

1。Before plastering the wall, the base layer of the wall must be cleaned. If the surface of the wall is smooth, it should be textured.

At the same time, the walls need to be layered when plastering. Each layer of plastering should not be too thick, and the interval time should be strictly controlled. After plastering, watering should be maintained to prevent hollowing or cracking.

2。When installing window frames, attention should be paid to the accuracy of size and height. There should be a certain amount of plastering space around the window frame to prevent plastering.

3。Before plastering the wall, the concrete wall should be chiseled, sprinkled with water, and then plastered with cement mortar. In the case of ceramsite block walls, an interface agent needs to be applied after wetting.

4。If the wall is not painted, the cement mortar variety and batch number should be consistent, and at the same time, the calendering should not be repeated in the same place, otherwise the depth of the wall will be different.

5。When spraying gypsum or soaking in ground fine lime powder, the curing time needs to reach a certain number of days before it can be used. Do new brick walls still need to be plastered? If the plaster contains unexcavated particles, it can easily cause bursting or flowering when plastering. ​

You can get it for free

Do you need plastering for wall tiling? Floor tiles are one of the commonly used building materials in home decoration. It comes in many styles and styles, and is loved by the public for its sturdiness and wear-resistantness.

In addition to the various styles of floor tiles, the laying methods are also different, and different floor tile laying methods produce different living room effects.

Do you need to close the plastering of wall tiles? Next, I will introduce you to ten personalized living room floor tile renderings to see if there is a style you like.

Do you need plastering for wall tiling? First, the diamond laying method.

Method: On the basis of the road surface in front, a 45-degree rotation effect is performed. During the construction process, it should be noted that the later cutting will increase the wear rate of the floor tiles, so when buying, try to buy more spare.

Two. Brickwork.

The one-time paving method of the square is the most popular paving method in recent years. Compared to the traditional I-paving method, the I-paving method gives a sense of movement and makes the lines more interesting.

Do you need plastering for wall tiling? Three. Chinese character layout.

The method is to choose two floor tiles and lay them diagonally at a 90-degree angle. This way of paving the car section cover is very suitable for the classical retro decoration style, such as the American living room, which is very suitable for making the space look retro and elegant. If you want to create a personalized effect, it is recommended to use diagonal bricks of the same specification and different color systems to create different effects.

Fourth, the method of laying fishbones.

This brick operation is more troublesome and is the legendary master strike series. Wood grain bricks must be processed in advance before being paved. Laying them consumes more energy. Therefore, we had to do a good job of communication in the early stages of construction. Wood grain bricks are divided into group A and group B, and the cutting direction is different.

Do you need plastering for wall tiling? Fifth, hexagonal laying method.

This tile has a rich sense of picture and is simply beautiful compared to traditional bricks. The construction process is not too complicated and is acceptable to the average teacher.

Six. Windmill Trail manages.

Choosing two or more colored tiles is one of the traditional laying methods. When matching, it is important to note that the width of the burnt rectangle edge must be twice the width of the rectangular edge, and the size of the rectangular edge must be the same as the width of the rectangle.

Do you need plastering for wall tiling? Seventh, the supplementary configuration of laying methods.

Complementary locations are often found in TV villas in the United States. It is a combination of large and small tiles. The size of these two tiles is unlimited. It's perfect for Western, American, and retro natural home outfits.

Eight. Imitation wool laying method.

The renderings of floor tiles in the living room are perfect for large spaces such as the living room. Choose a combination of squares and rectangles to create exotic styles with different specifications.

Do you need plastering for wall tiling? Nine. Point laying method.

Among the two or more paving methods of different sizes, the most common one is the point paving method, which is not too complicated to construct. It is loved by owners and builders alike.

Ten. Phased laying method.

This is also one of the Master Strike series, an invincible test of the master's skill, choose two kinds of large bricks and small bricks, when the number of large bricks is three times that of small bricks.

You can get it for free

For the newly built red brick wall, if you want to apply tiles, you generally need to plaster first. Here's why:

1.The flatness is not enough. The surface of the newly built red forest disturbed brick wall will have some unevenness and irregular brick joints. If the plastering treatment is not carried out, there will be obvious height difference and unstable center of gravity after the tile is pasted, which affects the beauty of the tile and makes this judgment effect.

2.Insufficient adhesion. The surface of the newly built red brick wall is dry and rough, which will affect the adhesion of the tile when it is directly applied to the tile.

After a plastering treatment, it can effectively improve the smoothness and adhesion of the surface of the red brick Li bridge wall, so that the effect of tiling is more beautiful and firm.

The exterior wall veneer brick project needs to do exterior wall plastering. Because the surface of the veneer brick should be smooth, smooth and firm, in order to make the veneer brick more firm.

Process flow of exterior wall veneer brick:

Grass-roots treatment: hanging vertically, setting squares, finding rules, pasting ash cakes, plastering bottom layer mortar, elastic line grid, row bricks, dipping bricks, inlaid veneer bricks, surface brick hooking and wiping.

Precautions: The construction environment temperature should be 5 350C.

Pasting construction is not allowed on rainy and snowy days.

The constructed materials should be protected from rain within 24 hours.

When interior decoration, whether plastering is needed when the wall is pasted with wall tiles, the following situations are explained for you:

1. If the wall is cement mortar, there is no need to plaster, but the wall should be smashed, rolled with interface agent or 801 glue (to strengthen the viscosity of paste), and pasted with wall tiles;

2. If the wall is scraped putty or paint finish, it is necessary to grab the wall skin and smash the hair, roll coating interface agent or 801 glue (to strengthen the viscosity of the paste), and paste the wall tiles; Just in case, it is best to do rough scraping before tiling. Scraping should be done with plain cement slurry (in some cases, it will also be required to add an appropriate proportion of rubber material), and brush all over the wall to ensure the gluing strength of the scraping material and the wall. The process of scraping itself is empty

Find the standard, use the level, the vertical ball, the hanging board for the collapse, generally every meter five up and down, nail a steel nail on the left and right, so that the outer plane of the steel nail in the standard position to be found, and then use cement mortar to wipe a small cake around the steel nail, and collapse into a steel nail that is flat with the standard of finding a good standard, it is called "collapse", and then connect the bar, it is called "pumping the pillar", wait until the "pillar" has a certain hardness, and finally smear the mortar with mortar between the column bucket and the missing sub, and then use a scraper to scrape it flat, Compacted with a wooden rub and rolled into a rough surface; After the base is half dry, it can be tiled.

1.According to the chemical properties of adhesive adhesives, they can be divided into inorganic adhesives and organic adhesives.

2.According to the physical state of the adhesive, it can be divided into liquid, solid and paste adhesives.

3.According to the ** of adhesives, it can be divided into natural rubber and synthetic rubber.

4.For common organic adhesives, according to the molecular structure, they can be divided into thermoplastic resins, thermosetting resins, rubber adhesives and so on.

5.From the application mode of adhesives, they can be divided into pressure-sensitive adhesives, rewetting adhesives, cyanoacrylic adhesives, delay adhesives, etc.

6.From the temperature range of adhesives, they can be divided into high temperature resistance, low temperature resistance and normal temperature use of adhesives.

7.In terms of the application field of adhesives, adhesives are mainly divided into civil engineering and construction, paper and plants, automobiles, aircraft and ships, electronic and electrical, and medical and health adhesives.

8.From the chemical composition of the adhesive, it can be divided into various specific adhesive types.