Is it really anti tank with a vise?

I think that if you give 1 minute, a skilled rogue can smash all the optical equipment on the tank with a vise, basically the tank is blind, and finally the pliers are stretched out of the plug barrel, and the destructive effect should still be relatively obvious, more reliable than dismantling parts, the key parts of the tank are not so easy to dismantle, it is estimated that the roof machine gun is removed and used with a general vice.

The goal of the next-generation tank pre-developed by the United States is to reduce the maintenance and disassembly tools of the entire tank to 7 pieces, and the field disassembly time of the main components is not more than 4 hours (with the support of the rescue vehicle, there are cranes and electric wrenches), but so far there is no design scheme that can meet the requirements.

A track weighs 2 tons, I don't believe who can move it alone, a piece of armor plate is 1 ton, who can unload it with pliers?

And it's anti-tank -- you said give me a crowbar and grenades, but it's still possible, at least Maozi's Red Army implemented a vice, and that's too sad, right== It's a long time to defuse the bomb with tactical tongs.

Dream on, many parts require multiple skilled craftsmen using many special tools in a dedicated site to disassemble.

It's impossible, it's possible to destroy the tank's engine in a short period of time under certain circumstances. You are a tank, and the machine guns and members are all wood?

It's all very imaginative, very artistic, and well, very ornamental.

No, you are just blocking the wall, and you can dig a hole out when no one is around. Some people on the Internet use 16mm steel bars to make anti-theft nets, which are also cut by hydraulic pliers, and ordinary families use 12mm thick ones at most. It's a safe, and there are also portable gas cutting guns to open it, and there are lasers used to make fences in science fiction, and the cost is estimated.

Even the vault of the bank, if there is no security, it will be opened, and there is no such thing as a one-and-done thing. It is recommended to install a stainless steel anti-theft net with optical fiber, and when the anti-theft net is cut, the optical fiber is also broken, so as to give an alarm, which can be transmitted to the mobile phone. **Available for sale.

What you're saying is too awesome, no matter how good the net is, it's also made of silk, and it can't prevent the vise, if you really want to get it, use the controlled one, this can be, the mouth of the pliers can't be opened so big.

We who sell chains are cut with this.

This thing is called a bolt cutter.

It is usually sold in hardware stores.

If the chain is thick, use the large one.

Hope it helps.

Ordinary vices can still be pinched with thin chains.

There is a difference between the vise and the needle-nose pliers in use: the vise is mainly used to hold, bend metal or cut off fine metal, and generally cannot be operated live, and special telecommunication vices can be operated live; Needle-nose pliers are mainly used to cut wires and are a common tool for electricians.

Vice, also called wire cutter, the front is flat-headed, in the actual work can act on the screwing and pulling of larger workpieces and the shearing of the wire, whether steel wire or wire or copper wire, as long as the pliers can leave bite marks, and then clamp the wire with the teeth of the front mouth of the pliers, gently lift or press down the wire, you can break the wire, very labor-saving.

Needle-nose pliers, also known as manicure pliers, are needle-nosed in front, mainly used to cut single-strand and multi-strand wires with thinner wire diameter, as well as bending rings for single-strand wire joints, stripping plastic insulation, etc., and the clamp handle is sleeved with an insulating sleeve with a rated voltage of 500V, which is one of the commonly used tools for electricians. Needle-nose pliers are used for operations in confined spaces due to their pointed heads.

The vise is also known as the wire pliers with a flat head in front, and the mouse pliers are also known as needle-nose pliers with a sharp nose in the front. In practice, the vise can be used for the twisting and pulling of larger workpieces and the cutting of iron wires, and the mouse viscer can be used for smaller workpieces.

Dream About a Vise Wrench - Dream Interpretation:

The days of constantly using your brain and mouth. Multitask, and don't forget to give some time to your lover. If you want to invest, you might as well find a few more people to discuss and evaluate. Work and study: If you hear untrue news, you will spread it out through your mouth, and be careful of causing trouble.

Dream about a vise wrench - good luck:

Can be stable, can escape disasters, subordinates can cooperate effectively, can succeed, by the love and promotion of the elders or the benefit of the father and ancestor Yu De, and the prosperity and great development. 【Dajichang】

Hello, these two are not easy to use, it is recommended to buy the wire special pliers shown below.

Hold down the shift key while clicking on the barbed wire. Not to cut it open.

If a blue vice appears, it means that the Sapper does not have one.

A lot of loose things can be done with the shift key. Sleepy pants will be handy.

To the side net downstream of the river can be clamped with pliers, not the front!

The flower mouth is actually prepared for rough machining, and the clamping surface of the workpiece itself is rough, so that the actual clamping force is a little better Is the straight mouth you are talking about is a flat mouth? This is designed for finishing clamping, because the workpiece has been rough-machined, the surface is relatively flat, so that the contact surface is large, and the clamping effect is good There are also some special-shaped jaws, which are more open to a V-groove, which is used to clamp the round bar workpiece, which not only has good clamping force, but also is easy to position. In short, the jaws of regular vise products can be machined by themselves and can be replaced by themselves (screw holes and positioning are standard and unified).