The Epson 590K printer boot lights are all flashing

Hello: It is recommended that you take off the ribbon and turn it on for testing.

If the ribbon can be fed and printed normally without installing the ribbon, it means that the problem is caused by the ribbon cartridge not being installed correctly, please reinstall the ribbon cartridge or replace the ribbon installation test.

If you don't install the ribbon printer, the lights will still flash when you turn on the printer, and the needle will stop on the left side. Please restore the printer to factory test:

First turn off the power of the printer, then press and hold "Wrap Page Change" and "Feed Unwind" and "Pause" at the same time, and then turn on the power of the printer, and let go when you see the light on the control panel of the printer.

If you still can't turn on and print normally after resetting the factory settings, please perform a printer self-test as follows to confirm whether the printer has a hardware fault

1 Make sure both the printer and the computer are turned off;

2.Load continuous paper or A4 sheets in the correct way in the feeder;

3.Press and hold the Feed and Unwind button, and then press the power button to turn on the printer. When the printer is powered on, release both buttons.

Normally, the printer will print the self-test page. If the paper cannot be fed and printed normally, the printer has a hardware fault, please contact the Epson Authorized Service Center for further testing. You can browse the following** to see the nearest service center:

Problems with the header or motherboard.

Summary. Hello, the two indicators of the Epson printer have been flashing to indicate that there is a fault, and the solutions are as follows: 1. The ink light is on and the power light is flashing.

The ink has been exhausted and the ink cartridge is not recognized. Solution: Press the key to change the ink to replace, and the printer will generally show a prompt, and you can operate according to the prompt.

Hello, the two indicators of the Epson printer have been flashing to indicate that there is a fault, and the solutions are as follows: 1. The ink light is on and the power light is flashing. The ink has been exhausted and the ink cartridge is not recognized.

Solution: Press the key to change the ink to replace, the general printer will prompt the defeated brother, according to the Fanchang prompt state dry operation can be.

Flashing at the same time. There is no shortage of ink.

2. The double bridge lights flash at the same time, and the mechanical so Sentong is a fierce obstacle, check whether there are sundries in the printer, and take out the sundries, most of which are jammed. If the parts of the wheel in the printer are damaged or broken, then the parts need to be replaced.

3. Flashing of two lights at the same time may also be due to the failure of the motherboard or sensor, and the motherboard or sensor must be repaired.

4. After the printer is turned on, the ink car does not move, and nothing can be printed, but the paper and ink lights are flashing. Solve the Fang clan only hidden method: add some steel shaft drip lubricating oil, check whether it is jammed.

4. After the printer is turned on, the ink car does not move, and nothing can be printed, but the paper and ink lights are flashing. Solve the Fang clan only hidden method: add some steel shaft drip lubricating oil, check whether it is jammed.

5. EpsonR210, R230 paper feed and ink light flash at the same time. Judgment and staring solution: the paper measuring sensor under the number cavity of the printer head, if the continuous supply is changed, check whether the length and length of the pipeline are appropriate, adjust the length of the pipeline, so that the length of the pipeline is appropriate when the word car goes to the left and right, and the problem can be solved.

6. The paper feed light and ink light of the printer keep flashing alternately. Solution: Clean up the waste ink and clean up the software.

Hello, I am happy to answer your questions and have found the answer for you, if the switch of the Epson printer keeps flashing, there may be the following reasons: First, the ink cartridge needs to be replaced:

If the printer's ink cartridge has expired or the ink has run out, the printer's switch will keep flashing. It is recommended to replace the cartridge with a new one. Clause.

2. The printer needs to be cleaned: After the printer has been used for a long time, some ink and dust may accumulate on the printhead, which will affect the normal operation of the printer. Printer cleaning is recommended.

For specific methods, please refer to the printer manual or contact after-sales customer service. Clause.

3. Printer connection problem: If the printer is connected to the computer or other equipment, it will cause the printer to fail to work normally, resulting in the switch flashing. It is recommended to check whether the cable of the printer brigade lead connection is loose or if the connection is correct. Clause.

4. Other faults: If none of the above methods can solve the problem, it may be that the printer has other faults, such as cartridge sensor failure, power failure, etc. It is recommended to contact after-sales customer service for repair or replacement.

It should be noted that there may be differences between different models of Epson printers, and the specific solutions may be different. It is recommended to check the printer manual or contact after-sales customer service when you encounter problems.

Dear, I'm glad to answer for you: Epson dot matrix printer boot all lights are on and flashing A: Hello kiss epson Epson Epson printer all indicators are flashing Reason analysis:

This problem is an error message that the printer trolley (the unit that drags the print head back and forth to move back and forth) cannot move properly, which is usually caused by paper jams, foreign objects falling, etc. Solution(s): Step 1:

When using the new machine for the first time, please pay attention to check whether the print head protective strip (blue) is removed, and remove the blue strip. Step 2: Check whether there is any paper jam or foreign object inside the printer, and take out the jammed paper or foreign object.

Step 3: Check the rear feeder for paper jams or cracked foreign objects, remove the paper jams or foreign objects and reinstall the rear feeders. Step 4; After the above checks, restart the printer.

Note: If the fault cannot be eliminated after the above methods, it means that the printer has a serious fault, please contact the service center to solve it. A printer is one of the output devices of a computer, which is used to print the results of computer processing on related media.

If you are satisfied with my service, please give a thumbs up, and once again wish you all the best! Peace and joy!