Router plus hub 3 computers to set up Internet access

1. Hardware connection: section chief house, ADSL --- router WAN, two LAN ports of the router--- two lines--- one is connected to the section chief's computer, one is connected to any port on the hub on the third floor through the small hole, and the other ports are connected to two other machines.

2.Settings: Set the PPPoE of ADSL in the router, and the router will directly dial up the Internet to access the Internet.

The IP address of the section chief's machine can be obtained directly, or set to, X may be any of the numbers 2-255. Or, x may be any of the numbers 2-255.

3.The other two machines are also set up in this way, and the last one is not repeated with the section chief, it is possible, and it can be arranged in order, for example, the section chief uses, and the other two machines can be used, 4Set up two shared folders on the section chief's machine, one is readable and writable, and the other is readable and not writable, (if you want to be writable and unreadable, which is impossible to drop).

The easiest way is not to connect the last two routers to the WAN port, but to the LAN port respectively, and turn off the DHCP of the last two routes, and change the LAN address to something else (not it, you have to note the change, otherwise you can't log in, and the modified LAN port IP is best written to the router to avoid forgetting).

In the above setup, the last two routers are switches, which are connected by wired and wireless connections'The computer is equivalent to the computer settings under the first router.

If the line port is not enough, you can only use the WAN port to connect to it, then you need to set the WAN port address of the second router to be careful not to be the same as the IP already used under the first router), assuming 50, the subnet mask remains unchanged, the gateway is changed to (that is, the LAN address of the first router), its own LAN port should be changed to the server to give the address range should also be changed to, and the IP address of the computer connected under it should be: , subnet mask, gateway.

Note: The DNS of all computers and routers is the same as that of the first router, an integer of 0255, and cannot have the same IP, otherwise there will be conflicts. There are three network segments above, all of which can access the Internet through the first router, but machines in one network segment can only access this network segment, and other machines cannot access other network segments.

Have three network cables ready.

A router.

1.Open and enter the configuration page of the girder shelterer (connect the LAN port of the computer and the router with a network cable, enter.

Username admin

Password admin - the back of the router has this information before the loss).

2.Open it in turn, network parameters - WAN port setting - WAN port type ppppoe, enter the Internet access and password, select automatic connection, and other defaults.

3.After setting up, connect the Internet network cable to the WAN port of the router, and connect the other three computers to the LAN port.

4.As soon as the router is powered, it will be automatically connected, and 3 computers can access the Internet.

First of all, install the router, power on and "one network cable" to access the "WAN" port of the router, and any one that needs to access the Internet is connected to the computer and the "LAN" port of the router with a connection cable. Turn on your computer and type " in the browser address bar.

tp-link as an example), press enter to enter the routing setting interface, and set the dynamic and static mode, Internet mode, account and password, etc. (Remember that the IP and DNS of the local connection are set to automatic data acquisition) so that the router is set up, and you can browse the Internet with Qiaodai! Connect to the other network cable, set the above IP and DNS and you're good to go!

Easy to solve. A router is a must.

**Wire to cat.

The cat picks up the road and trembles by this thing.

Go online and look it up. Router settings.

Follow step by step.

It's okay to lose it.

Hehe. In IE, there are changes in the address column.

Look on the router).

Username admin

Password admin

Hehe. Set up POP dial-up Internet access.

Input. Password.

Are you sure. That's it.

One router is used as a primary router, and the other two are used as secondary routers. There are two ways to do this:

1.Change the connection mode of the second-level router, connect the network cable connected to the LAN port of the first-level router and also connect to the LAN interface of the second-level router, at this time the second-level router is used as a switch, there is no need to set the WAN interface parameters, directly connect the network cable to the computer, just log in to set the wireless part of the parameters can be used, the wireless terminal searches for the wireless signal of the wireless router and enters the encryption key, and can be connected and used after verification;

2.Another way is to use the WAN interface of the second-level router, at this time the router is working in the routing mode, connect the computer with a network cable to log in to the second-level router, set the second-level router WAN interface to dynamic IP mode or static IP mode (the static IP address needs to be set according to the login IP address of the first-level router), and then set the parameters of the wireless part. However, it should be noted that the IP address assigned by the LAN of the second-level router must not be in the same network segment as the first-level router, otherwise there will definitely be conflicts;

3.In general, in the case of cascading multi-level routers, the first-level router needs to be set to the route mode, that is, after logging in, enter the WAN interface settings-PPPoe mode, and enter your broadband account and password.