How to set up the router to connect the two computers, please 3Q

I found one for you on the Internet, you will know after you read it, it's very simple, just connect the ** wire to the cat, find a network cable to connect the cat to the router, and then find two network cables, and connect the two computers to the router. The key is the configuration of the router. Let's take a look here.

First of all, disconnect the lenient waiter, enter the address block: The password is admin There is a setup wizard after entering, select pppoe dialing, and enter the lenient password. After the connection is successful, you will be able to access the Internet.

First, set both AB computers to automatically obtain IP addresses and DNS. Then, check the network segment of computer A: If the address of A is, then the network segment of your old router is, and the router address is.

Then, start the new router (you don't need to go online, just plug it in), connect the computer C to the downlink port of the new router (LAN port, any of the four ports), wait for a while, and then check the address obtained by C. If the address of A is, then the CIDR block of your new router is, and the new router address is. You need to enter this address in the browser of computer C, enter the management interface, change the network segment to the LAN management area, and the address of the new router will become, and restart the router.

Then, connect the network cable from the modem to the uplink port (WAN port) of the old router, and I believe you have done this. Then, connect Computer A to any of the downlink ports (LAN ports, one of the four ports) of the old router, and I believe you have done this. Then, unplug the network cable connected to computer B from computer B and connect it to the uplink port (WAN port) of the new router.

Then, with a new network cable, connect Computer B to the downlink port (LAN port, one of the four ports) of the new router. Now, on each computer, run the "Command Prompt" and enter the following two commands separately to make sure that the computer gets the new IP address: 1

ipconfig /release 2.ipconfig renew Then, confirm that computer A is on and computer B is on. In this way, both machines will be able to access the Internet.

The current router is generally automatically set to IP Our dormitory six faces can be used, your problem seems to be a router problem, you can try it according to the practice on the first floor, if you can't enter, it may be that your router is not, you just look at the instruction manual.

The IP of the two computers should be the same, and the router should have a disc to put the disk in.

What about the new computer can ping the route?

If only one IP address is available, it is recommended that you connect the incoming network cable to the WAN port of the router and the other three computers to the LAN port. I don't know what network segment the IP address assigned to you by the unit, if it conflicts with the network segment of the router, for example, the network segment of the unit Internet is, and if the router's is also this section, you have to first change the router LAN port address to another network segment, such as: then configure the static IP address given to you by the unit on the WAN port, and then configure your three computers to 3, 4 three addresses, masks, gateways, DNS to find a good one to use, such as good luck.

If you have multiple IPs that you can use as you like, you can connect the incoming network cable and three computers to the LAN port of the router and use it as a switch, hehe.

Between two routers? Didn't you take the wire from the switch above? How did it become two routers interconnected again?

Generally speaking, cross-wires are used for the same type of equipment, and direct wires are used for dissimilar devices. Under normal circumstances, the router should be connected to the switch with a direct cable. But now there are a lot of devices that can already be adaptive, if you can't adapt, some have cascade ports, so it's not easy to determine what wire to use, you can try it according to this rule first.

I haven't really seen a broadband router used by a general unit or enterprise with so many ports, and the 24-port one you said may be a switch.