How to set up Leike router to access the Internet on two computers at the same time?

Step 1 Connect the router, ADSL device and computer (see box and instructions) Step 2 Enter the router.

Enter the address shown in the address bar of your browser as shown in the following figure and press the Enter key to confirm.

As shown in the following figure, the following window will appear.

Enter the username and password Username: guest Password: guest Step 3 Set up the router.

After entering the router, set the router and do not modify the default parameters.

Click WAN Settings in the left menu bar with your mouse.

Select PPPoE User (ADSL) in the corresponding right-hand column, and enter the PPPoE account number (Internet access account provided by Netcom or Telecom) and password (Note: please do not modify other setting parameters).

When you're done typing, tap the Apply button.

Step 4 Check whether the router is successfully dialed.

After the third step is completed, click the system information button on the left to detect whether the dialing is successful.

This router supports crack upgrade, please log in to upgrade the program.

The router I use is a Leike NR255

Hope it helps.

Cat--- router (WAN port) -- the other two computers are connected to the LAN port of the router respectively, and modulated according to the method in the operation manual. In the WAN settings, click on PPPoE users, and fill in your broadband dial-up username and password into the application. Another computer can also access the Internet directly by connecting the network cable to the router LAN port, note that the router has helped you dial up.

Two cases:1You can now go on whether it has been configured in it, if so, then the local connection of another computer is set to automatically obtain the IP address, DNS, and then connect to any port of the router 1234 with a network cable.

2.If you haven't configured it at all, just connect to the router 1234 port through the computer's broadband connection to dial up the Internet, then you don't use the router at all, in this case, you have to configure, the cat is connected to the router (WAN port), the computer is connected to the router LAN port, so connected, the local connection of the computer is set to automatically obtain the IP address, DNS, and then go into the configuration interface, in the WAN settings, click PPPOE user, and fill in the username and password of your broadband dial-up application. Another computer is directly connected to the router LAN port can also access the Internet, pay attention to the router has helped you dial up, every time you turn on the computer to access the Internet, you don't need to point to the broadband connection to dial up the Internet, you can access the Internet directly on the computer.

In fact, the one named Nie Feng has already explained it in detail. It's just the hardware side. If you are using Telecom's broadband pass, then you have to use your computer to access the Internet as early as the latest version of the new dream broadband pass, and then you can access the Internet at the same time.

If one computer (a) uses a wireless network card and the other computer (b) uses a network cable. A is connected to the WiFi of the router, and B is connected to the LAN port of the same router. The IP addresses of both computers are set to the same network segment (e.g. and.

1. Use a router as the main router, which can be used to connect to the external network and enter the router settings page. 2. Click DHCP Server on the left, select DHCP Service, enable DHCP Service, and use the default address for the start and end addresses of the address pool. 3. Click the setup wizard on the left side of the router settings interface, select the Internet access method through the setup wizard, enter the corresponding Internet access, password, or static IP address, etc., and transfer the external network connection.

4. Connect the LAN port of the computer and the auxiliary router with a network cable to enter the secondary router settings page. 5. Click the network parameters on the left, set the WAN port connection type to dynamic IP on the WAN port settings page, and click Save. 6. After restarting the router, log in again to enter the router settings page, click the DHCP server on the left, select the DHCP service, enable the DHCP service, and set the address pool start and end addresses as segments, and click Save.

7. Connect the LAN port of the main router and the WAN port of the auxiliary router with a network cable. At this point, the two routers are connected.

It should be said that your current 2 computers are already a local area network.

Yes, you can go online and share files.

Both of them only need to turn on the print file sharing service.

Because your two computers are under the same router, they are in a local area network, and the computer system has network sharing turned on by default.

1. First of all, you need to set the router parameters, if there is a manual, follow the manual step by step. If there is no manual, connect the computer to the router with a network cable, enter the computer address bar: or, enter the user name and password according to the prompts, it should be admin, log in to the router, according to the settings wizard prompts, select dynamic IP, static IP or PPPoe mode, enter the parameters provided by the network operator to you, save the parameters, restart the router, and the setting is complete.

2. Connect the incoming network cable to the WAN port of the router.

3. The computer IP address acquisition method is set to automatic acquisition.

4. If you also want to share files or printers on your computer, select Network Connections from the Control Panel, select Set Up Home or Small Office Network, and select Share Files or Printers.

Because the router itself also has a switch function, if you don't have access to the Internet, only two computers will be shared, and only the fourth step can be performed.

If you're satisfied, please give it back.

The two computers are connected to the LAN port of the router, and the network cable is connected to the WAN port.

One way is to plug the router into port 1 as a switch with the main line instead of plugging it into the WAN port.

You can also take advantage of the router auto-dialing feature by as:

1。A computer is connected to router port 1, and then enter the router IP from the IE address bar (some are written on the back of the general router, and if not, it is on the manual).

2.Enter the account password is admin

3.Select Quick Settings, select ADSL Virtual Dialing (PPPoE) Next, enter your broadband account password, and follow the prompts.

4。Plug the main line into the WAN port.

Connect to your computer with a plugged in cable, and you can access the Internet without dialing up.

By the way, if you want to increase the boot speed.

Just click on the network neighbor attributes, local connection attributes, general, Internet protocol attributes, use the following IP, IP bar such as a router is you set to yes.

The subnet mask gateway is the IP address of the router

Use the DNS server below.

If your school has blocked the router and you can't connect to two computers at the same time, use the router as a switch.

Use a computer as the main unit.

The way to do this is to use a computer to view the local IP address of the host computer.

Click on the local connection to see it.

If the IP is if your school does not prohibit static IPs, you can set it yourself).

On the other computer, the IP is set to , except 78) and the subnet mask gateway is set as the host.

Set up DNS host networking.

In this case, it is recommended to use a switch, some routers are not easy to use, my previous router is.

Type in your browser:

Username: admin

Password: admin

Quick setup--- ADSL (PPPoE) - Enter the username and password (account and password for broadband Internet access) - done.