I have two hard drives, how do I connect them. Thank you for pointing out

Two hard disks can be connected to an IDE data cable, but in this way you have to set up a jumper, so that one of them is the main disk, and the other is a slave disk, and the jumper settings are all on the hard disk, and the hard disk shows that the jump is the main disk and how to jump from the disk. If you still can't, you can directly find two IDE data cables, one after the other hard disk, so that you don't have to worry about any P jumpers. Hehe.

There is no need to jumper when connected to two wires separately.

You have to jump one after another, and the brand is not the same, and you can generally remove one of the jumper caps.

There is an interface in the middle of the cable that connects you to the hard disk, but it is very short, and it is OK to connect it.

Be bold and careful, and you will be able to take it a few more times!

There are three possibilities for using dual hard drives at the same time:

Both hard drives are IDE hard drives. If you want to connect two IDE drives to one of the IDE ports on the motherboard at the same time, you must set up master and slave disks for both disks.

Both hard drives are SATA hard drives. Since SATA hard drives work independently, they do not interfere with each other and have no conflicts, so no special settings are required, and the data cable and power cable can be used normally if they are properly connected.

An IDE hard drive and a SATA hard drive are used at the same time. This situation is similar to case 2. Since the communication buses of the IDE port and SATA port are independent of each other, there is no conflict, and the data cable and power cable can be used normally if the data cable and power cable are properly connected.

Look at the jumper instructions for the hard drive (IDE on the back of the hard drive, SATA on the manual). Then buy a jumper cap. (Note that it is one!)

Attach the jumper cap to the third pair (the third pair of vertical pairs) pins on the 60g hard drive. Finally, connect the data cable. SATA can be connected casually, IDE needs to connect the middle port to the 60G hard disk, and the end one to the 40G disk.

If your system is on 40G, you need to format the 40G and then install it on the 60G.

If you have two IDE ports on the motherboard, you can use two IDE cables, and the IDE ports on the motherboard are marked with the words "IDE0, IDE1", and you connect your original disk to IDE0 (it becomes the main disk) and connect the other one to IDE1. That's it. If you have to plug it into a line, jump the jumper of the hard drive (::

Plug the jumper into the first two pins is the main disk, and the other piece of the jumper is removed and not plugged in is from the disk. Remember to remove the hard drive jumper that you want to use as a slave disk, otherwise it will conflict with the first hard drive.

The system is installed on the main hard drive, and the other is not installed.

The serial port does not need to be set.

Plug it in and use it.

The parallel port needs to be set.

Master-slave disks (system disks are the main).

There are three ways to use dual hard drives at the same time:

1. Both hard disks are dust-sensitive first IDE hard disks. If you want to connect two IDE drives to one of the IDE ports on the motherboard at the same time, you must set up master and slave disks for both disks.

2. Both hard disks are SATA hard disks. Since SATA hard drives work independently, they do not interfere with each other and have no conflicts, so no special settings are required, and the data cable and power cable can be used normally if they are properly connected.

3. An IDE hard disk and a SATA hard disk are used at the same time. Since the communication buses of the IDE port and SATA port are independent of each other, there is no conflict, and the data cable and power cable can be used normally if the data cable and power cable are correctly connected.

Plug in a terminal, depending on what way you want, such as simply adding a hard disk, Shousen partition use, or RAID, or Shenmu dynamic disk. Hyo-woo.

1.If it is an IDE, plug the two disks into IDE 1, and the long cable is connected to the computer motherboard, and the short end has two IDE connectors, the upper one is connected to the main disk, and the lower interface is connected to the slave disk, and the English name of the slave disk is at the beginning of S. Generally, the boot sequence of computers starts from the main disk and boots one by one.

2.In the case of a stat hard disk, the primary disk is inserted on sata1 and the secondary disk is inserted on sata2.

3.If one is an IDE and the other is SATA, then we use the large capacity as the main disk interface, see the hard disk plugged in, and set the master-slave jumper.

Hard disk is one of the main storage media of a computer, consisting of one or more aluminum or glass discs. The disc is covered with a ferromagnetic material.

Hard disks include solid-state drives (SSD disks, modern hard disks), mechanical hard disks (HDD traditional hard disks), and hybrid hard disks (HHD is a new hard disk born based on traditional mechanical hard disks). SSD uses flash memory particles for storage, HDD uses magnetic disks for storage, and hybrid hard disk (HHD) is a kind of hard disk that integrates magnetic hard disk and flash memory.

The vast majority of hard drives are fixed hard drives that are permanently sealed and fixed in the hard drive.

Head Reset Energy Saving Technology: Energy savings are achieved by resetting the head during idle hours.

Multi-head technology: It is used in servers and database centers to speed up the disk by adding multiple heads to read or write at the same time on the same disk, or to use the head to read or write to the disk at the same time on multiple disks.

Each hard disk cable can be sold to connect two hard disks, if the original hard disk cable is connected to the hard land travel disk and optical drive, you need to use a new hard disk cable The motherboard has two ports that can be connected to two hard disk cables You will connect the new hard reed disk to the wire, connect the power plug, and set the jumper on the hard disk to be different from the original (such as the original main disk, the new disk is set as a slave disk, or the original is a slave disk, the new disk is set as the main disk) You can use it You don't need to reinstall the system

First of all, you need to buy a hard disk power plug, and you also need to buy a hard disk data cable, and 2 of them can be plugged in