Why does my hard drive read on the old computer but not on the new computer?

Summary. If your old hard drive won't read on your new computer, here's why:1

Incompatible interface: The interface type of the old hard disk is not compatible with the new computer, for example, the old hard disk is an IDE interface, while the new computer only supports SATA interface. 2.

Insufficient power: If your new computer doesn't have enough power to power your old hard drive, it won't be able to read properly. 3.

Driver issues: If your new computer doesn't have the required drivers installed on your old drive, it won't be able to read your old drive properly. 4.

Hardware failure: If the old hard disk itself has a hardware failure and cannot be read properly. Workaround:

1.Check interface compatibility: If the interface type of the old hard drive is not compatible with the new computer, you can buy an adapter or adapter cable to solve the problem.

2.Check the power supply: If the power supply is insufficient, you can try replacing it with a higher power supply.

4.Check for hardware failures: If your old hard drive has a hardware failure, you can try connecting it to another computer or send it in for service.

If your old hard drive won't read on your new computer, here's why:1Interface incompatible:

The interface type of the old hard drive is not compatible with the new computer, for example, the old hard drive is an IDE interface, while the new computer only supports the SATA interface. 2.Insufficient power:

If your new computer doesn't have enough power to power your old hard drive and it won't be able to read properly. 3.Driver issues:

If your new computer doesn't have the required drivers installed on your old drive, it won't be able to read your old drive. 4.Hardware failure:

If the old hard drive itself has a hardware failure and cannot be read properly. Workaround:1

Check interface compatibility: If the interface type of the old hard drive is not compatible with the new computer, you can buy an adapter or adapter cable to solve the problem. 2.

Check the power supply: If the power supply is insufficient, you can try replacing it with a higher power supply. 3.

Check for hardware failures: If you are stuckIf your old hard drive has a hardware failure, you can try connecting it to another computer or sending it in for repair.

If your old hard drive won't read on your new computer, here's why:1The ruler port is not compatible.

2.Insufficient power:3.

Driver issues:4.Hardware failure:

Workaround:1Check Interface Compatibility:

If the interface type of your old drive isn't compatible with your new computer, you can buy an adapter or adapter cable to solve the problem. 2.Check the power supply:

If the power supply is insufficient, you can try to replace it with a higher power supply. 3.Install the driver:

If your old hard drive has a hardware failure, you can try connecting it to another computer or send it in for service.

Hello everyone, I'm Daming, the old computer hard disk installed on other computers should not have the problem of not reading the disk, if the old computer is using the "IDE hard disk interface" or "SATA hard disk interface", then it depends on whether other computers are also old computers or have the same hard disk interface, but according to the information described by the questioner, the "hard disk" has been installed on other computers, there should be no different interface problems, the key to the problem is still in the installation or setting of the hard disk, So then I will talk about the detailed operation steps, <> to solve this kind of problem

Check whether the hard drive data cable and power cable are loose

The first thing that should be ruled out is whether the "hard disk" has a virtual connection problem, it may be that "not reading the disk" is just an illusion, the real reason is actually that the "motherboard" does not detect the "hard disk", the detailed operation steps are to open the "chassis" to connect the hard disk to the motherboard's "data cable" and "power cable" to re-plug and reinforce, in order to ensure the correctness and <> of the hard disk installation

The motherboard BIOS re-identifies the hard drive

Because some old motherboards in the installation of large-capacity hard disks, must be in the BIOS settings to reload the "hard disk", the motherboard is recognized, of course, the motherboard is not this problem now, the detailed operation method is to boot into the BIOS interface and select to switch to the "IDE hard disk options" select "auto" to automatically identify the hard disk, and finally press F10 to save and exit, <>

Summary

This Q&A explains the analysis and solution of the reasons for "not reading the disk" in the case of changing the host of the "old hard disk", and my conclusion is that there are two points of "loose installation of the hard disk" and "the old motherboard BIOS needs to re-identify the large-capacity hard disk", basically there will be no "no reading disk" situation

The above is the content shared today, I hope it will be helpful to everyone, if you like it, don't forget to like and follow! Daming will continue to create works on "computer maintenance and application", if you have different views on such issues, you can discuss them together in the comment area, open the "app".", search for "computer technician Daming", there are more original computer knowledge, for your reference, this issue of Q&A is here, let's see you next time!

The main reason is that the motherboard is incompatible, the motherboard of the new computer may not support the hard disk model on the old computer, which will cause the motherboard to not recognize the hard disk, and naturally cannot read it.

In many ways, there are aging lines or hard disk failures that cause data to not be read, or another computer hardware mismatch or system problems, depending on the specific situation

May not be compatible. Because with the progress of the times, the protocol for exchanging data by computers has also changed a lot.

The most likely thing is that the BIOS is not set, that is, press F12 to enter the motherboard settings interface before booting, then find the hard disk, set the boot disk, and that's it.

Check whether the hard disk data cable and power cord are loose, and the old motherboard BIOS needs to re-identify the large-capacity hard disk, and basically there will be no "no disk reading" situation.