What is the electrostatic dry powder pond porcelain liner of electric water heater, and what is the

Dry enamel equipment can not be done in China, only imported, and imported to Germany's dry enamel is the best, ** is about 15 million - 20 million, dry enamel is the use of electrostatic low temperature spraying process is characterized by strong adhesion and corrosion resistance, long service life, wet enamel is to the enamel powder by high temperature into water and then put in the inner tank and then shake left and right to hang the enamel water naturally in the inner tank, such a high temperature enamel in the use of the process because it is hung on the inner tank in a high temperature environment, Therefore, the thermal expansion and cold shrinkage of the enamel and the inner tank are not the same, so it is easy for the enamel to fall off in future use, and the low-temperature electrostatic spraying is sprayed at low temperature due to the spraying, there is no cold and heat difference, so it is not easy to fall off in the future use, I don't know if LZ can understand? The wet enamel equipment is only more than 2 million.

Dry enamel is characterized by strong adhesion, corrosion resistance, and long service life; It is easy for the enamel to fall off in the use of wet enamel.

The dry enamel adopts the electrostatic low-temperature spraying process, which is characterized by strong adhesion, corrosion resistance and long service life; Wet enamel powder is to be turned into water by high temperature and then put in the inner tank and then shake left and right to hang the enamel water naturally in the inner tank, such a high temperature enamel in the use of the process because it is hung on the inner tank in a high-temperature environment, so the enamel and the inner tank of the thermal expansion and cold shrinkage is not the same, so it is easy to fall off in the future use.

The low-temperature electrostatic spraying is not easy to fall off in future use because it is sprayed at low temperature and there is no difference between cold and heat.

It refers to the coating method of coating the body with porcelain glaze dry powder.

There are several ways to do this.

Impregnation method: the red hot body is submerged into the dry powder of the glaze. It is mostly used for the coating of the glaze of small cast iron products.

Spraying method: the glazing method of spraying glaze powder on the green body. It is mostly used for flat or large enamel products. The control, operation and operation of this enamel coating powder can be fully automated, and can save energy consumption and improve the utilization rate of raw materials.

Sprinkle enamel method: the glazing method of sprinkling porcelain enamel powder on the body. It is mainly used for glaze coating of cast iron products.

Dry powder enamel is to use the principle of electrostatic adsorption to cover the surface of the enamel glaze with a layer of organic grease, so that the enamel powder has a conductive function, which is conducive to the use of electrostatic effect for metal surface enamel.

Aren't you buying a brand-name product? The products of large companies generally have better after-sales service and are more responsible. The small fault repair of the electric water heater is almost the same, and the big fault is not at ease even if it is repaired.

It's better to buy a new quality product. In recent years, the products have been improved in many aspects such as electric heating efficiency, thermal insulation performance, safety guarantee, and control performance. The national standards for inspection, energy consumption, and safety have also been standardized and improved.

**It's not too high compared to other appliances.

If the electric water heater has been used for 6 to 8 years, it should also be actively updated.

Minor faults will be repaired, and major faults will be replaced with new ones.

Repair, find the corresponding after-sales department, and play ** for maintenance.

Boss, there is no concept at all, you dare to open a factory, liner stamping, argon arc welding, inner wall sandblasting, electrostatic dry powder enamel processing equipment, shell making equipment, fluorine-free polyurethane foaming machine and so on.

How to use the electric water heater:

1. When opening the mixing valve for bathing, the nozzle should not be directly facing the human body, and should be used when the water temperature is adjusted to a suitable time to avoid the water temperature being too high or too low to bring discomfort to the user. When bathing, make sure that the water sprayed does not pour onto the water heater to prevent the internal wiring of the water heater from being damp and causing a short circuit, causing danger.

2. After you finish bathing, you should first keep the nozzle away from the human body, then close the mixing valve, turn off the power of the water heater, and at the same time shake off the water in the nozzle. And hang the sprinkler head on the sprinkler mount.

3. If the user does not use the water heater for a long time, the water in the inner tank of the water heater should be emptied to prevent the smell and scaling of the inner tank due to waterproof deterioration.

Drainage method: first close the tap water inlet valve, then pull the water heater mixing valve to the hot water, and then pull the safety valve handle up to the horizontal position, then the water in the water heater liner will flow out through the pressure relief port of the safety valve and flow to the sewer through the discharge pipe.

4. Before the water heater is powered on, it must be ensured that the inner tank of the water heater is filled with water. Otherwise, it will cause the water heater to burn dry, damage the heating pipe, and cause the thermostat to trip.

Water injection method: pull the mixing valve to the hot water, then open the tap water inlet valve, and when the nozzle continuously discharges water, it indicates that the water in the inner tank of the water heater is full, and then it can be heated by electricity.

How to use the electric water heater:

When using the electric water heater, turn on the power and the indicator light is on, indicating that the electric heating is being made, when the water temperature reaches the set value, when the temperature inside the water heater reaches a certain temperature, the electric heating part will stop working to protect the electric water heater. The electric water heater (storage type) should be filled with water first, then heated with electricity, and can be used after preheating. In case of a drop in water pressure or a sudden water outage, it is best to turn off the power.

2.Electric water heaters are equipped with a faucet and have a return device, which is usually used"Blue"I show cold water and use it"Red"Indicates hot water.

3.On the temperature regulator of the electric water heater, there is a water temperature marker scale"i"、"ⅱ"、"ⅲ"Or indicate the position of the low, medium and high adjustment of the water temperature in English, Arabic numerals, and point the temperature adjustment knob at a certain mark, and the water temperature of the water heater will be maintained at the temperature set by the gear indication. When using, let the water spill out to test the actual water temperature before showering to prevent the water temperature from being too high and scalding**.

4.When filling the water, the water outlet must be opened, and the air in the inner tank must be completely discharged before checking whether the water is full. The power supply must be cut off before emptying.

For enclosed installations, the inlet valve must be open during heating. When you first open the valve, do not turn the water outlet in the direction of the human body.

Tips for using water heaters in the spring world 1: use the original pressurized shower of our factory: large flow and high water temperature. (No matter how good your shower is, but it is not pressurized, it may cause cold water to flow out without sufficient heat absorption, which will seriously affect the use effect.) ）

Skill 2 for using Quantianxia water heater: Before use, you can touch the smart push-to-talk to make the water temperature rise to 70 degrees quickly before use, and the effect is better. (In the "Lilian" and "Prime Minister" series, the 3rd or 4th gear is the smart key.) The "Field" series is an independent smart key. ）

Tips for using water heaters in Quantianxia 3: Proper water temperature and flow are very important! The optimal water temperature for human skin contact is between 37 and 42 degrees Celsius, and too high water temperature is not good for maintenance, which is easy to cause dryness and itching.

Don't turn on the flow too much, try to keep it between 4 and 7 litres. In this way, it is used in a balanced way to ensure a continuous supply of hot water.

Tips for using water heaters in Quantianxia: Try to install the water heater closest to the shower to reduce heat loss from the water pipes.

Tips for using water heaters in Quantianxia five: When decorating a new house, it is best to pre-embed a copper core line of 4 to 6 square meters in the bathroom and kitchen. Try to install the Quantianxia 80 model in one step, the temperature rises quickly, the cooling is slow, and the suitable water temperature flow hot water source is continuous.

Hope it helps.

1. Plug in the power supply, press the switch button of the electric water heater, and set the water temperature at the same time. Normally, I set it at 45 degrees, but in winter, the temperature can be turned up a little higher.

2. After the water boils, first adjust the valve to the middle position, put the water, and try that the water temperature is not cool before starting to use. (Generally, the left side of the valve marked with the word H is hot water, and the right side marked with C is cold water.) Hot water is marked in red, and cold water is shown in blue. )

3. After the water temperature is constant, it can be used, because the electric water heater is surrounded by water, which is easy to be electrocuted, so try not to touch other places with your hands or other parts during use, especially around the power supply.

4. When using the electric water heater, when the water valve is opened and there is no water, the power supply should be disconnected immediately to prevent the electric water heater from being damaged due to failure when working without flowing water.

5. If the water pressure or voltage is too low, the use should be suspended.

6. After use, turn off the switch on the electric water heater first, wait for your hands to dry, and then unplug the power.

The correct installation and use of electric water heaters.

1.In winter, it is best to 75 degrees, and the electric water heater will automatically store water after boiling, and the hot water will be available after washing for a long time.

2.Of course, you don't need to store water, it's all automatic.

3.When you use it, you can plug it in, and when you don't take a bath, you can adjust the temperature of the water heater to 40 degrees, as long as it doesn't continue to heat, it doesn't cost electricity.

Electric water heaters are divided into instantaneous type and storage type (water tank), and are divided into electromagnetic type and non-electromagnetic type (electric heating pipe). Instantaneous types are generally equipped with electric walls and have high power. The water storage type is divided into simple type (without insulation layer, without electric wall, not for live use) and ordinary type (with insulation layer, with electric wall, can be used with electricity).

The electromagnetic water heater can completely separate water and electricity, never leak electricity, and there is no need for an electric wall. Electric tubular water heaters need to use anti-electric walls to prevent leakage.

1. According to the season and the amount of water consumption, it should be set up in winter, and it should be adjusted at about 42 degrees in summer.

2. The water in the water tank of the storage electric water heater is always full, because the hot water in the water tank is based on the cold water from the tap water to enter the water tank and push the hot water out, so there is no need to worry about whether there is water in the water tank.

3. It depends on the frequency of your use and how much water you use, the frequency of use is high, and it is best to always keep the power on, which is not only convenient to use, but also relatively energy-saving, but if the frequency of use is low and the water consumption is small, it is best to heat up before use, especially in summer, generally about 20 minutes of electricity can meet the requirements of bathing.

1. Turn on the power supply, and the power indicator is on.

2. Adjust the temperature gear low in summer and mid-range in spring and autumn and high in winter 3, check that the heating indicator is bright when heating, and observe the temperature display rise process 4, open the water outlet side valve of the mixing valve when bathing, and the cold water valve of the mixing valve can be opened to adjust if the water is too hot 5, and turn the temperature control to OFF when not used all day, and adjust to the corresponding temperature control gear before using it again.

What's going on with the leakage switch tripping.

Turn on with hot and cold water! See for yourself!

If the electric water heater is broken, it is nothing more than a broken heating pipe and a broken temperature control device, as long as the inner tank does not leak and the accessories can be replaced. As for whether it is worth repairing, it depends on your own personal preference.

Don't use this kind of cottage electric water heater, it's too risky. Let's hit it with the brand. Haier, Midea, Vantage, etc.

No, boiling water will produce harmful substances after 24 hours of incubation. The continuous insulation and heating of the electric water heater will make the water more abundant in harmful substances.

Even if the water in the electric water heater is boiled in a kettle, it is not drinkable. Because warm water will produce a carcinogen after being left for a period of time, just like our hot water bottle is best not to drink after overnight, the reason for not being good for the body is the same.

Usually, the maximum temperature of an electric water heater is 75 degrees Celsius, and drinking water should be boiled at 100 degrees Celsius before drinking.

Drinking it will cause diarrhea, so the water from the electric water heater is not drinkable.

No, it should be that the water has not been treated! It is directly heated and released, there may be germs, the electric water heater is not sterile boiling water, and the boiling point of water is 100 degrees! And the temperature of the water heater is only a few tens of degrees!

No, because it is not boiled.

No, because it is not sterile boiling water, there may be pathogenic bacteria.

It's not expensive, it's normal. Because your electricity price is high. Normally, it should be about five cents a degree.

If these appliances work every day, it's normal! This is normal for so many electrical appliances to have less than 200 kWh of electricity a month! If you live alone, it is normal to turn on these appliances every day.

It's expensive, and for verification, you can memorize the meter number, use it for a day, and do the math. The problem is big to find a landlord. If you want, buy an electricity meter, two dozen dollars, and measure it yourself. The electricity bill is not only about power, but also about loss, and the power labeled on electrical appliances is not necessarily accurate.

It's not expensive, electric water heaters, induction cookers, and refrigerators are very power-consuming

It's too cheap, really, the water heater is very power-intensive, not to mention the battery.

It's not expensive, I'm here for a long time, just a computer and a kettle, all seventy or eighty!

It's very cheap. The refrigerator is constantly plugged in and consumes a lot of power

It's not expensive, and it's not much to check for this money

8 cents are more expensive, do you use these household appliances? How much time? This is the point.

It's not expensive, I have 1 block and 1 degree here.