What is the fault of the Volkswagen Bora dashboard failure light, and the light of the brake pedal i

Volkswagen Bora. Brake bulb fault lamps use diagnostic instruments to clear fault codes. A faulty brake light indicates a problem with the vehicle's braking system, caused by brake pads worn to the limit, brake discs worn to the limit, or a lack of brake fluid.

Here's why the brake light stays on:

1. Lack of brake fluid.

When the driver presses the brake pedal.

, the force that is stepped down from the pedal is transmitted by the piston of the brake master cylinder to each brake sub-cylinder located at the wheel through the brake fluid, so that the brake pad is in contact with the wheel, so as to achieve the purpose of stopping the vehicle from advancing;

2. The tail light bulb is damaged, and the brake fluid cup is divided into upper and lower lines, when the brake fluid inside is lower than the lower line, this phenomenon will be sensed through the sensor next to the oil cup, and reflected by the brake light on the dashboard. If the brake fluid decreases quickly, it means that there is a leak in the braking system;

3. The brake pads are seriously worn, and the lights will always be on, so the brake pads need to be replaced.

Hello! I think there is still a problem, it must be caused by loose wiring in the system or internally, of course, we must pay attention to safety, and we must pay attention to failure.

Hello: Because the vehicle is driving, the brake pads will wear out, the brake fluid level will drop, the brake oil pot will alarm, just add the brake fluid to the lowest line.

Go to the shop to inspect the brake assist system, including brake disc wear.

Hello This situation is a problem with the brake switch, check it. Hope mine can help you.

Brake pedal. icon.

What this icon stands for: possible causes.

Reason 1: If the gear lever lock button is not pressed, the car cannot start driving.

Reason 2: The brake pedal was not pressed.

Workaround. For reason 1: Press the shift lever lock button (illustrated) to engage the shift lever locking mechanism. The indicator light will turn off automatically.

For reason 2: Hit the brake pedal before starting and destroying the step.

1.If the brake light is broken, the brake cable may also be faulty; Solution: The brake light switch is damaged.

Find the liquid wax brake light switch, unplug it after finding the brake light switch, and connect it directly with a wire. If the brake light is on, the brake light switch is broken. You can change the switch to a new one.

2.Check whether the brake fluid is sufficient or whether the brake pads are worn; Solution: The brake fluid is insufficient, and it should be replaced in time.

3.Red is a warning that the vehicle cannot be driven. Generally, the brake fluid is not reduced, and the handbrake is not loosened; Workaround:

There are two main reasons for a red light. One is insufficient brake fluid, and the other is excessive wear of the friction pads. No matter what kind of car owner, it is necessary to send it for inspection and maintenance in time, otherwise it will seriously endanger driving safety.

4.Yellow is also a warning light, but it is mild enough to continue driving, but you need to check it immediately. For example, the thickness of the brake pads is not enough, and the ABS system fails. Solution: Replace with a new brake pad.

5.Green is the indicator light. There is a brake lock that closes automatically to prevent accidental closing. The parking position is locked without pressing the brakes. At the same time, the green light of the instrument is on, and it goes off when you step on it.

Detailed description of the brake light: Wild Burial.

1.Ordinary cars are equipped with two brake lights, the brake lights are on the left and right sides, and some cars have a high-mounted brake light on the rear windshield. When the brake light fails, one of the brake lights does not light up.

2.The function of the brake light is that during driving, the owner presses the brake pedal, and the brake light will light up, which can remind the rear car to keep a certain distance. Without this brake light, the vehicle behind will not be able to keep its distance from the owner, causing a traffic accident.

3.Brake lights are easily damaged parts, and vehicles need to be used repeatedly during driving, so brake lights are easy to break. When the brake light system fails, repair the car immediately to ensure the safety of the vehicle during driving.

Check the brake fluid first.

Whether it is enough, brake pads.

Whether it is overworn. Generally, there is no fault in the braking system, which is the handbrake.

The switch is a problem.

Extended Information: The handbrake light is on and the brake system light is on for the following reasons:

1. If the handbrake is not completely put to the end, you can pull the handbrake and put it back in place to see if it is still bright.

2. Brake fluid.

Leakage, you can go to the repair shop or 4S shop to check and repair the location of the brake fluid leakage, and then replenish the brake fluid, these two lights will go out and return to normal.

3. The brake pads become thinner, causing the brake fluid level in the brake fluid pot to drop, and when the brake fluid level sensor is turned on, the handbrake light will be lit, but the oil volume will drop to just when it seems to be turned on and not connected, the handbrake light will turn on and off with the shaking of the vehicle.

Therefore, please first check the amount of brake fluid, open the hood, look at the brake fluid level of the brake fluid kettle, there is a scale on it, if it is indeed too little brake fluid, then you should check whether the brake pads are worn to the limit.

Check the brake light switch and check the brake light wiring.

Summary. Hello, I am your exclusive technician, attentive, careful, dedicated to answering your car questions, for you to find the corresponding problem solutions and solutions!

The light of the brake pedal appears on your face. It's normal, not malfunctional.

1.The light of the brake pedal is on the gauge, and the light will only turn on the ignition without pressing the brake.

2.When the brakes are applied, the lights will turn off automatically. When the light on your face goes out, the gear lever can be unlocked, and then you can put the gear on.

What is the fault of the Volkswagen Bora dashboard failure light, and the light of the brake pedal is on?

Hello, don't worry, I can ask for your question, but wait a minute, I need text for about 2 minutes.

I am your exclusive technician, attentive, careful, and dedicated to answering your car questions, and finding solutions to the corresponding problems and solutions to pure bends for you! The light of the brake pedal appears on your face. It's normal, not malfunctional.

1.The light of the brake pedal is on the gauge, and the light will only turn on the ignition without pressing the brake. 2.

The reasons why the Bora car lights up as soon as it steps on the brakes: 1. Lack of brake fluid; 2. The brake pads are worn to the limit; 3. The brake warning light line is short-circuited. The solution to the fault light when you step on the brake:

1. Do a good job of high temperature protection, prevent corrosion of the brake system, prevent the brake pads from biting due to high temperature, and eliminate the screaming of the brake pads; 2. Change the brake fluid regularly; 3. Clean the oil stains, dirt and friction dust of the brake disc, brake drum and any parts to keep the brake disc heat dissipated well.

Reasons why Volkswagen has loose and abnormal sound in the rear wheels:

1. The tire is stuck with a foreign body, check whether the tire is stuck with a foreign body.

2. If there is a problem with the brake shaft, check the rear wheel bearing.

3. The driving road is uneven, which will also cause abnormal tire noise.

4. The brake pads are worn, and you can lightly step on the brakes at this time to determine whether it is related to the brake pads.

5. The sound caused by the impact of tire pressure problems.

Reasons why Volkswagen has loose and abnormal sound in the rear wheels:

1. The tire is stuck with a foreign body, check whether the tire is stuck with a foreign body.

2. If there is a problem with the brake shaft, check the rear wheel bearing.

3. The driving road is uneven, which will also cause abnormal tire noise.

4. The brake pads are worn, and you can lightly step on the brakes at this time to determine whether it is related to the brake pads.

5. The sound caused by the impact of tire pressure problems. Volkswagen Bora generally causes the rear wheel abnormal sound of the following situations: 1, the tire stuck with a foreign body, check whether the tire is stuck with a foreign body.

2. If there is a problem with the brake shaft, check the rear wheel bearing. 3. The driving road is uneven, which will also cause abnormal tire noise. 4. The brakes are worn, so you can step on the brakes lightly to determine whether it is related to the brake pads.

5. The sound caused by the impact of tire pressure problems.

Abnormal tire noise refers to abnormal sounds that are abnormal and easy to attract the attention of the driver during driving. In such cases, experienced drivers can often tell the cause by the sound of abnormal noises. Among them, the sound of "popping and clicking" is mostly the sound of the tire stuck in the stone or the nail after the Zen eggplant is pierced.

The "stinging, stinging" sound is mostly caused by friction when the brake pads are too thin. There is also a tire noise that becomes larger, the tire pressure is too high, and the direction is lighter.

Photo by Pacific Automobile Network Q&A).

Regarding the landlord's concern about "what happens to the Volkswagen Bora brake light always on", the following is my personal opinion:

What's going on with the Volkswagen Bora brake lights always on? Volkswagen argues that the reason why the brake light is always on is that there is a short circuit in the circuit or a malfunction of the brake light switch. If the brake fault light on the dashboard is often lit and carries the data chain, it is caused by the failure of the brake system, and the parts need to be replaced or brake fluid added in time.

The method of disassembling and replacing the brake light is as follows:

1. Use a Phillips screwdriver or sleeve to remove the bolts;

2. Pull the lamp assembly out of the rear column;

3. Turn the socket counterclockwise and remove it;

4. Remove the old bulb and insert the new bulb.