What are the reasons why mechanical watches are not gone?

Mechanical watches. There are generally many reasons for not leaving, such as insufficient power reserve, insufficient power, beating or shock, lack of oil in the movement, and so on.

1.Insufficient battery storage: First you need to check if the battery is sufficient.

A self-winding mechanical watch may also cause a lack of energy if it moves a little bit. You can replenish the power by manually winding it up and then observe whether it continues fast or slow. If it is not because of the lack of kinetic energy, it is that the mechanical watch is broken and needs to be repaired by a professional repairman.

2.Low battery: If you suddenly notice that your watch is running slowly, it's most likely caused by a low battery. That's when the battery needs to be replaced.

3.It was hit or hit: the table was tight. If it is hit or struck, it may cause loose and damaged internal parts, and it may also cause the mechanical watch to not work. It is recommended to go to the store for inspection.

4.Lack of oil in the movement or wear and tear of the internal parts can cause the mechanical watch to not work and need to be maintained.

Mechanical watches can be divided into two types: manual winding and automatic winding, the difference is that one needs to be manually turned to turn the crown to wind the internal spring of the watch; Automatic is the process of winding the mainspring by oscillating the autopilot on the movement. The mainspring inside the barrel releases pressure through the gears to drive the pointer to run, and the advantage of a mechanical watch is that it does not need to replace the battery, and it relies entirely on mechanical parts to operate, but it needs regular maintenance.

In the process of using the mechanical watch, there is an error or does not go when it goes, which is generally a problem in the following situations:

1. Lack of power:You need to check whether the power is sufficient, if the amount of movement of the self-winding watch may also cause a lack of power reserve, you can manually wind the crown to replenish the power, and then observe whether it continues to run and whether there is any slowness.

2. The watch is magnetizedThe core component of a mechanical watch is the balance wheel, which has a hairspring, and if the hairspring of a mechanical watch is magnetized, the watch will not be affected by the time.

3. The watch is short of oil:If the time is long, the watch oil of the movement will be dry, resulting in a lack of oil and the internal parts will be worn, which will cause the problem of running out of time, and need to be cleaned and maintained.

4. Knock and collision:In the process of wearing, if the watch is accidentally bumped or impacted, because of the precision of the parts, it may cause the internal parts to be displaced or worn loose, etc., and the time is not accurate or not to go.

5. Other reasons:In addition to the above common situations, some influences of ambient temperature, wearer's usage habits and other influences may cause the occurrence of time error.

If there is a time error in the process of wearing a mechanical watch, you can take it to your nearest Guangcheng watch store for watch time detection. If you have any problems with your watch, welcome to leave a message to share!

First, mechanical watches have "three proofs" (waterproof, shockproof, and anti-magnetic), if there is a problem in these places, and it is more serious, the watch will not go this kind of problem. Second, there are other faults in the movement, even under the premise of taking care of themselves, there is no problem because of the "three preventions", and the mechanical movement may also have other problems, such as untimely maintenance, lack of oil in the movement, etc., which may cause the mechanical movement to stop. Third, it is also possible that there is no problem with the watch at all, but you did not wind the watch in time.

We know that manual movements need to be wound frequently, but automatic movements are not always motivated as long as you wear them often, and automatic movements should also be manually wound according to the actual situation.

For example, the lack of power of a mechanical watch, or the magnetization of the watch hairspring, which can cause damage to the parts through collisions, can cause the hands to not move. Usually you should also bring more watches to increase the kinetic energy of the watch. A lack of oil in the watch can also damage the parts, causing the hands to not move.

There are many reasons why a mechanical watch does not go, and the most common possibility is because of insufficient power, if we do not wear the watch for a long time, it will also lead to insufficient power of the watch. In addition, we should protect the watch well when using a mechanical watch, if it bumps into a certain place, it may also cause the mechanical watch to malfunction.

In fact, there are generally two situations in which the mechanical watch does not go, the first is because of insufficient kinetic energy. The second is due to a malfunction of the mechanical watch. Common faults include bumping, misalignment of movement gears, magnetization of the watch, long shelf time, oil sludge drying, etc., which will cause the mechanical watch not to go.

Therefore, don't panic too much when you find that the mechanical watch is not leaving, and first distinguish which kind of big one it belongs to.

The first reason is that I haven't worn it for a long time.

If you haven't worn the watch for a long time, it may be because it is not winded, so the watch has no power, resulting in a situation where you can't walk normally. So you only need to rewind it and then make subsequent adjustments to get the watch back to normal use.

The second reason is caused by a fault.

Bump problems. Why the mechanical watch is not gone, it may be more because the watch has a certain failure, especially when the movement and gear inside the watch are bumped, which may cause failure, which can not be restored by simple adjustment. Therefore, it must be disassembled through a formal maintenance organization, so as to determine the internal situation to know how to deal with it.

There are many reasons why the mechanical watch does not go, first of all, it may be the reason for the lack of energy of the mechanical watch, even if it is an automatic mechanical watch, if the usual arm activity is relatively small, there will still be insufficient energy replenishment and cause stopping, and secondly, it may be that the watch movement is damaged, the gear is misaligned or damaged and stops, so try to wind it first, or there is no movement and then contact customer service for repair.

The first way to deal with the failure of the mechanical watch: if it is found that the mechanical watch does not move after inspection, it is because the mechanical watch is faulty, it must be sent to the technical professional maintenance personnel to carry out maintenance, remember not to disassemble the mechanical watch by yourself.

The second way to deal with insufficient kinetic energy: To deal with this kind of situation, you only need to put the watch back on and then exercise normally. Or take off the watch and shake it for less than 2 minutes before going to bed. It is recommended to wear the watch for at least 6-8 hours a day.

Mechanical watches run by the push of mechanical gears and clockwork, and rotation will inevitably cause friction, so it is necessary to oil and lubricate the watch for a long time to reduce the amount of wear and tear of parts. Otherwise, if you don't repair it until it breaks, this kind of problem is already very serious.

What to do if the mechanical watch is gone, how to wind the mechanical watch.

There are several reasons why a mechanical watch doesn't move:

The time is too long, the internal oil is lacking, and the due maintenance has not been received for a long time, and the friction of the mechanical parts increases, and it will not be able to move over time;

Affected by the external environment, the loss and fall of manpower leads to the dislocation of internal precision;

Internal moisture, corrosion, damage and aging of components, etc.

In short, there are many reasons that can lead to failure.

What to do if the mechanical watch is gone, how to wind the mechanical watch.

Stop, there may be the following reasons:

1. See if the crown is pulled out, the crown is pulled out, and the watch stops.

2. Whether the second hand touches the glass, there will be a circle mark on the glass.

3. Whether the three watch hands are not well balanced, causing contact and causing stopping.

4. Whether the battery is exhausted or not, it generally needs to be replaced in 1-2 years.

1.The power of the table is insufficient.

An automatic watch only needs to be wound by moving your arm, but if you don't exercise much, or if you don't wear your watch for too long, the watch may not be able to run out of time or stop due to lack of power. Of course, you don't have to throw your arms as a hula hoop in order to wind your watch, just move normally.

2.Wearing time is too short.

If it's really caused by too little exercise, don't worry, just take off your watch and shake it horizontally for about 2 minutes before going to bed, and of course you can also shake it for 4 minutes, because then it can walk longer. If your watch can be wound, you can also wind it clockwise. In order for your watch to last longer, it is recommended to have him wear it on your wrist for at least 6 to 8 hours a day.

3.Hairspring failure.

If neither of the above two reasons is the case, it may be the cause of the hairspring. If you exercise too much, the clockwork will be tighter. If it is really a lack of power caused by the winding, usually between 9 and 12 o'clock in the evening, the "calendar function table" at this time his needle wheel began to drive the calendar wheel, the load is large, the watch is tired, at this time if the power is insufficient and no one pushes it, it is easy to stop.

During this time, don't reverse the dial, many mechanical watches have a plastic calendar wheel, and if you are not careful, you will break the gear, if you break the tooth, it will be stuck at this time every day, or it will no longer jump until a fixed date. That's why the mechanical watch stopped.

4.Bump failure.

The parts of the watch are very delicate and small, if you are careless and accidentally bump into it, or if you are healthy and bump into it. This can easily cause the movement parts to fall off or break directly.

So what happens if the mechanical watch stops? The automatic winding box can solve this problem, the watch can be placed in the box when not worn, and turn on the switch to automatically wind. The rotating watch box is electronically numerically controlled, which can be timed to automatically wind automatic watches and mechanical watches.

1. Power reasons.

That's right, many mechanical watches suddenly don't go because of lack of power, so mechanical watches don't have to be too nervous, because some fully automatic mechanical watches cancel the function of the watch chain, so some people think that automatic mechanical watches don't need to be wound at all, in fact, this is a misunderstanding.

Method: We wind the mechanical watch to see if it will run; Automatic watches should be worn at least 8 hours a day, and if they are not worn regularly, they can be wound by hand to make up for the amount of the mainspring, and if they are not manually wound, they can hold the watch and shake it gently.

2. Magnetic field causes.

If it's not an electrical problem, it could be that we are in a magnetic field. The watch cannot be moved due to the magnetic field. Mechanical watches are more affected and are easily magnetized, while mechanical watches are easy to fix after magnetization.

Method: Check if there is a magnetic field around the object, or change the position can be tried.

3. This mechanical watch is broken.

Common faults include bumps and vibrations. The movement gears are misaligned, the watch is magnetized, and the soil dries out after a long period of use, etc., all of which will cause the mechanical watch to not move. If the strings are straightened and the watch does not go, then the movement should be out of order.

Method: Or go to a professional repair shop or after-sales center in time to repair and see if there is any damage. In daily life, you should also take care of your favorite watch, try to avoid collisions, and don't often let the watch touch your hand, and send it to the watch store regularly for maintenance.

There are two principles for mechanical watches to move:

1. Mechanical watches rely on mainspring winding to provide power, and timekeeping is carried out by gear transmission. Mechanical watches are divided into manual and automatic winding. Due to the complex structure, the phenotype is thicker and heavier.

Because of the characteristics of the principle of time, it is affected by gravity, mechanical friction, temperature changes, usage and other reasons.

2. Mainly from the wearer's wrist activity, the flying weight of the watch swings when the owner is active, so as to wind the watch, so when the wearer usually does not have much activity or does not wear it for a long time, the string force will be insufficient or empty, resulting in the mechanical watch is not accurate or stopped.

There are a few things to keep in mind about the daily care of mechanical watches: In order to ensure the proper operation and accuracy of your watch, we recommend that you maintain your watch regularly.

1. The watch is tested for waterproof and appearance cleaning once a year.

2. Watches with mechanical movements should be maintained once every 3-5 years.

3. This not only keeps the watch in good running condition, but also effectively prolongs its service life. However, the above warranty service is only applicable to watches under normal wear conditions, and does not include watches that are worn abnormally or subjected to constant shocks.

1. There are generally two kinds of situations in which the mechanical watch does not go:

1. Insufficient kinetic energy: The fully automatic mechanical watch operates by the automatic winding mechanism that can tighten the mainspring when the rotor rotates in any direction. Only when the watch is worn on the hand, the rotor rotates to generate energy as the arm moves.

Generally, a fully automatic watch should be worn on the hand for more than 8 hours a day to replenish the mainspring. Therefore, if you do not wear it for a long time, or if you do not exercise enough after wearing it, it will also cause the mechanical watch to not go. In such cases, manual winding can be used.

2. Mechanical watch failure: it needs to be sent to a professional maintenance personnel for repair. Remember not to talk about mechanical watch disassembly yourself.

Mechanical watches are driven by mechanical gears and clocksprings, and friction is inevitable when turning, so it is necessary to add oil and lubrication over time to reduce the wear rate of parts. It is advisable to inspect mechanical watches annually for improper use or water ingress. For example, sweat, rain and dirty air accumulate for many years, causing slow erosion to machinery, and the frequency and degree of damage are much higher than those in Europe, America and Japan, so regular inspection is very important; Then it needs to be thoroughly cleaned and maintained every three years.

2. Suggestions for the use of mechanical watches:

1. Watches with manual winding movements should be wound at the same time every day as far as possible so that the watch has enough energy to operate in the next 24 hours. The energy of a watch with a self-winding movement is the movement of the wearer's arm, so it does not need to be wound manually under normal wear, only when the wearer's movement is not enough to replenish enough energy to the mainspring, the manual winding method can be used to compensate, and the crown rotation is controlled within 20 revolutions when winding.

2. If a self-winding watch has not been worn for more than 40 hours, the crown should be turned 20 times to reactivate the movement when it is worn again. To prevent moisture from penetrating the case and to maintain the water-resistance of the watch, make sure that the crown is locked at all times.