The machine start up alarm is urgent to help solve it

Pay attention to the graphics card, if the graphics card is replaced, see if there is a problem with the power supply to the graphics card on the motherboard.

The following is an explanation of the alarm sound, you may have a memory error one, 1 short sound - the system boots normally.

2. 2 Short Tone - General Error. The CMOS reset error option should be entered.

3. 1 long and 1 short - RAM or motherboard error.

4. 1 long and 2 short tones - the monitor or graphics card is wrong.

5. 1 long and 3 short - the keyboard controller is wrong.

6. 1 long and 9 short - motherboard flashram or eprom error.

7. Uninterrupted long sound - the memory is not plugged in or the chip is damaged.

8. Non-stop ringing - the monitor is not properly connected to the graphics card.

9. Repeating a short sound - power failure.

10. No sound and no display - no power, or the CMOS battery is drained, or the CPU is wrong.

1. If the sound keeps ringing, it may be that the memory module is not plugged in tightly2. If the sound is fast and short and rings twice (such as drip, drip): it may be that the CMOS setting is wrong and needs to be reset, this situation occurs the most, and the bottom of the screen (generally in the bottom left) will appear in English prompt "CMOS checksum failure", and then ask to press F? （f？

It could be F1 F12, depending on the motherboard) to load the default settings or enter. In addition, this problem may also occur after flashing and updating the BIOS, just load the default settings.

3. If the sound is a long sound and a short sound, it may be a memory or motherboard error.

4. If the sound is one long sound and two short sounds, it may be a monitor or graphics card error.

5. If the sound is one long sound and three short sounds, it may be the keyboard controller error.

6. If the sound is one long sound or nine short sounds, it may be the flash RAM or EPROM error of the motherboard BIOS.

1. If the sound is only a short sound, it may be a memory refresh failure.

2. If the sound is fast and short twice, it may be a memory ECC verification error.

3. If the sound is fast and short twice, it may be that the basic memory check of the system has failed.

4. If the sound is fast and short four times, it may be that the system clock is wrong.

5. If the sound is fast and short five times, it may be that the CPU has an error.

6. If the sound is fast and short six times, it may be a keyboard controller error.

7. If the sound is fast and short seven times, it may be the real mode error of the system.

8. If the sound is fast and short eight times, it may be a memory error.

9. If the sound is fast and short nine times, it may be a BIOS chip inspection error.

10. If the sound is one long sound and three short sounds, it may be a memory error.

What kind of alarm method is it? Is it a tick or something? Who can help you with your brainless sentence.

Is there a long and two short alarm sounds? Please check the graphics card, if it has been a rapid alarm sound, please check the memory module, it is recommended that you remove it and use an eraser to erase the gold finger of the memory module and the graphics card, and then reinstall it back.

This alarm is generally more because there is a problem with the BIOS of the motherboard, try to clear the CMOS and then turn it on, if it is still like this, then rewrite the BIOS.

You can clear the 0 BIOS with a jumper first.

The optical drive equipment and others are also unplugged, leaving the hard disk, memory, CPU, heat dissipation, and if the boot still rings, then you can only use the motherboard detection card to find out the fault.

Your ringing is in the memory location, and you will find out if there is a problem with the memory socket when you use the motherboard to check the card.

Speechless, everyone has said that they have changed the memory and graphics card, and then they have changed the motherboard and the CPU.

If you can't do it yourself, you can send it for repair, and it will be better if you can't do it yourself during the warranty period, and you can only send it for repair If you have multiple computers, you also have more perseverance, you can try to replace it, and you can't do it, or send it for repair.

It should be that the memory is not plugged in properly and there is a problem with the contacts.

It's best to test the circuit.

It's hard to say.

Summary. Hello, happy to answer your <>

The machine alarms, and the reason why it can't start is that the power switch is faulty. It is recommended that you clear the coms in case of a power failure, restore the default settings of the coms, and give it a try. If the fan can be turned on, the motherboard will be powered normally.

You can remove the CPU and put it on another computer that can run normally, but if it can't start, the CPU is broken. The above is the reason why the machine alarm cannot start.

What should I do if the machine alarms and can't start?

Hello, I am glad to answer the alarm of the machine for you, and the reason why it cannot start is that the power switch is faulty. It is recommended that you clear the COMS in the event of a power failure, and try the default settings of the restored COMS. If the fan can be activated, it means that the motherboard has a normal power supply.

You can remove the CPU and put it on another computer that can run normally, but if it can't start, the CPU is broken. The above is the reason why the machine alarm cannot start.

Kiss <>

Expansion: The machine is a device assembled from various metal and non-metal parts, which consumes energy and can be operated and modified. It is used to replace human labor, to perform energy transformation, information processing, and to produce useful work.