How to adjust single and double grains in the spoon wheel corn seeder

Corn seeder refers to the planting machinery that takes crop corn seeds as the sowing object.

Corn seeder refers to the planting machinery that takes crop corn seeds as the sowing object (taking into account soybeans and other crops), and usually the name of the seeder is often named with the name of the crop type, such as corn seeder, grain seed seeder, corn hole seeder, cotton seeder, forage spreader, etc.

How to use corn seeder: wxnongye01

The corn seeder has the characteristics of uniform sowing, consistent depth, stable row spacing, good soil covering, seed saving, and high work efficiency. The correct use of the seeder should pay attention to grasp the following 10 points:

1 maintenance before entering the field to clean up the debris in the sowing box and the grass and soil on the ditcher, to ensure that the state is good, and to the tractor and seeder of the transmission, rotation parts, according to the requirements of the instructions to add lubricating oil, especially before each operation to pay attention to the lubrication and tensioning of the transmission chain and the tightening of the bolts on the seeder.

2 The frame should not be tilted After the seeder is connected to the tractor, it should not be tilted, and the front and rear of the frame should be horizontal when working.

3. Do a good job of various adjustments According to the provisions of the instruction manual and agronomic requirements, the sowing amount, the row spacing of the ditcher, and the depth of the ditching and covering soil suppression wheel are appropriately adjusted.

4 Pay attention to the seeds added to the seed box to achieve no small, straw and impurities, so as to ensure the effectiveness of the seeds; Secondly, the amount of seeds added to the seed box should be added at least enough to cover the entrance of the seed box to ensure smooth seed arrangement.

5 trial sowing In order to ensure the quality of sowing, before sowing in a large area, we must insist on trial sowing 20 meters and observe the working condition of the seeder. Agricultural technicians, local farmers, etc., are requested to test and consult, and confirm that they meet the local agronomic requirements, and then carry out large-scale sowing.

6 pay attention to the uniform speed of straight line driving agricultural mechanic to choose the operation walking route, should ensure that the addition of seeds and machinery in and out of the convenience, sowing attention to a uniform speed straight forward, can not be fast and slow or stop halfway, so as to avoid reseeding, missed sowing; In order to prevent the ditcher from clogging, the lifting of the seeder should be operated in the middle of the road, and the seeder should be lifted when it is backwards or turning.

7 Sow the head of the ground first sow the head horizontally, so as not to roll the head of the ground hard, resulting in too shallow sowing depth.

8. Observe often observe the working conditions of the seed discharger, ditch opener, mulcher and transmission mechanism when sowing, and eliminate them in time if there is blockage, clay, grass entanglement, and poor seed covering. Adjustments, repairs, lubrication or removal of tangled grass must be done after the park has been stopped.

9 Protect the parts When the seeder is working, it is strictly forbidden to reverse or turn sharply, and the lifting or landing of the seeder should be carried out slowly to avoid damage to the parts.

10 Pay attention to the seed box The seeds in the seed box shall not be less than 1 5 of the volume of the seed box during operationWhen transporting or transferring plots, seed boxes must not contain seeds, let alone other heavy objects.

Summary. The adjustment method of the hand-pushed corn seeder: the adjustment of the corn plant spacing is mainly changed by replacing the transmission sprocket, and when the planter leaves the factory, the intermediate gear is 17 teeth each, the gear on the pressing wheel is generally 19 teeth, the gear on the seed dispenser shaft is generally 20 teeth, and the plant spacing is 21cm.

If you want to increase or decrease the plant spacing, you can change the sprockets with each other, and the number of teeth may be different for different tools, but the adjustment method is the same.

The adjustment method of the hand-pushed corn seeder: the adjustment of the corn plant spacing is mainly changed by replacing the transmission sprocket, and when the planter leaves the factory, the intermediate gear is 17 teeth, the gear on the pressing wheel is generally 19 teeth, the gear on the seed shooter shaft is generally 20 teeth, and the plant spacing is 21cm. If you want to increase or decrease the plant spacing, you can replace the chain celery Bishan wheel with each other, and the number of teeth of the machine may be different but the adjustment method is the same.

We hope you found this helpful, and we apologize for any trouble caused.

Hello dear I am glad to answer your questions, the single grain adjustment method of the hand push corn seeder is as follows: 1Start by placing the planter on a stable ground and placing the corn seeds in the seed box.

2.Adjust the size of the opening under the seed box to accommodate different sizes of seeds. 3.

The bridge then pushes the seeder to where it needs to be planted, pushing the handle forward so that the seeds fall high from the seed box into the soil. 4.If it is necessary to adjust the amount of single seed, this can be done by adjusting the single grain adjuster above the seeder.

Usually, a single grain adjuster is a small lever or knob that adjusts up or down the speed and number of seeds falling into the soil. 5.When adjusting the amount of single seeding, you can first push the seeder to a certain distance and then check the seeding effect.

If the seed density is too large or too small, the single grain adjuster can be adjusted appropriately until the desired sowing effect is achieved. The following is a ** tutorial for adjusting a single grain in the hand reading empty push corn planter, for your reference, I hope my answer can help you.

Hello dear! We'll be happy to answer for you. What to do with double grains under the corn planterA:

Kiss you with a good cover, one side of the seed shooter of the corn planter has an adjustment handball, the partition of the seed shooter can be moved up and down when pulled outward, at this time, the upward adjustment can be sown small seed corn, downward can be sown large seed corn, after the adjustment, turn the ground wheel ** on the row of seeds, if there is no cavity or double seed phenomenon (stable single grain seeding) can be operated in the ground. Precautions: Larger or smaller corn kernels need to be adjusted by replacing the spoon wheel.

Summary. 1. Different varieties of corn seeders, the number of plant spacing of the stalls is different, such as the double-printed corn seeder, the plant spacing of 6 gears is 30cm, generally in the process of sowing operations, it is necessary to ensure that the corn seeder moves forward at a uniform speed, and the sowing work can not appear fast and slow.

2. At the same time, pay attention to the regular professional inspection of the effect of sowing, check whether there are holes or the problem of substandard seeding through spot checks, and closely observe the operation of the machine, and find that abnormalities need to be stopped in time for inspection.

How to adjust the distance of the hand-pushed roller corn planter.

Hello, we have received your question and are working hard to prepare the answer for you, and will reply to you within five minutes! Wait a moment! ^

Hello, the distance of the seeder can be adjusted by adjusting the screws.

1. Different varieties of corn sowing first bucket machine, the number of plant spacing of the stalls is different, such as the double-printed corn seeder, the plant spacing of 6 gears is 30cm, generally in the process of sowing operation, it is necessary to ensure that the corn seeder moves forward at a uniform speed, and the sowing work can not appear fast and slow. 2. At the same time, pay attention to the effect of sowing on a regular professional inspection of socks, check whether there are cavities or the sowing amount is not up to standard, and closely observe the operation of the machine, and find that the abnormality needs to be stopped in time for inspection.

Dear, hello, I am glad to answer for you, according to your question, for you to inquire about the following: 1. There is a handball on one side of the corn single-grain seeder seeder, and there is a partition to control the seeder in the handball, and there is a gap in Xianglu above the partition, when the gap is adjusted upward, it is suitable for sowing small corn seeds, and when this gap is adjusted downward, it is suitable for sowing large corn seeds. 2. There are two buckets of the hand push corn planter, and there is a toggle device under the two buckets, and the number of corn kernels can be adjusted by adjusting the toggle device.

Second, how to adjust the corn sowing machine gear generally has 5-8 gears, adjust the gear can control the sowing plant spacing, generally adjusted to the first gear of the plant spacing of 15 cm, the second gear of the plant spacing of 18 cm, the third gear of the plant spacing of 21 centimeters, the fourth gear of the plant spacing of 24 cm, the fifth gear of the plant spacing of 28 cm, the sixth gear of the plant spacing of 30 cm, the seventh gear of the plant spacing of 33 cm, the eighth gear of the plant spacing of 36 cm.