How can my meter go faster

Your experience is special; First of all, let me talk about the problem of your landlord stealing electricity with a switch: the method is actually not complicated, connect two wires in parallel outside the meter (to bypass the meter), and use a switch to control the direction of the current; When using high-power electrical appliances, he turns on the switch, and the electricity connected from the outside does not pass through the meter; When you are done with the switch, turn the switch on; This is a very bad means of stealing electricity, and if it is discovered, it will be fined 3 5 times.

Let's talk about your meter again: First, it may be that there is a problem inside your meter, (there are many possibilities, I won't go into details) But as you said, the meter has not been touched by anyone, so I don't think it is likely that the meter itself is broken; Second, it is possible that someone is playing a ghost and occupies your line. (Since your landlord has the ability to make the connector of the switch even the people in the power company can't see it, then you have to check your wiring carefully, there may be a hidden connector in the corner).

He connected a wire to a switch installed in his room at the outgoing end of your meter's live wire, so he could steal your electricity. I suggest that you check the line at the end of the live line of your meter to see if there is a line that is connected to him (if there is, cut it), so that you can do it.

If you rule out the problem with the meter itself, then your landlord is likely to put a wire on your circuit and use it on his side. Control with a switch on his side.

When your own electrical appliances are working, disconnect the wires of the circuit in the room from the junction box one by one, and try to disconnect which one of the meters does not go away, that is, the wire is taken over.

That line will not be used again. The electrical appliances on that line can be used for other wiring.

Your electricity bill is too expensive, right?

Do you live in **? Electricity bills are so high! Changing places to live solved the problem.

Current transformers.

It is one of the three main functions of the transformer (change voltage, change impedance, change current). As long as you change the coil ratio, you can change the output current, and control the speed of the meter.

Changing the wiring will not make the meter "flush away" faster. It can be used to wire the current transformer for the second test on the current transformer in reverse winding 1 2 turns. The reverse winding can reduce the transformation ratio and make the table go faster.

Now that the meter can't be adjusted, it's impossible for people to let him go fast, and it's illegal to say that.

Use all the appliances you can use in your home.

The current transformer is one of the three main functions of the transformer (changing the voltage, changing the impedance, and changing the current). As long as you change the coil ratio, you can change the output current and control the speed of the meter. You can put the secondary test wiring of the current transformer on the current transformer and reverse it for 1 2 turns.

The reverse winding can reduce the change ratio to make the table go faster, and the positive winding can go slower.

The electricity bill we pay each month is calculated according to the amount of electricity shown on the meter for each month. When we have electricity in our home, the meter will slowly turn to calculate how many kilowatt-hours of electricity you are using. If the power of the electrical appliances used is relatively large, the meter will turn faster, and the electricity and electricity bills will naturally go up.

So what's going on with the meter going fast?

1.Check for leakage Turn off all household appliances in your house and observe the speed of your electricity meter. If it's still fast, it means the house is leaking.

You'll need to see an electrician to investigate the specific cause of the leak. Finding the cause of the leak can solve the phenomenon of the meter running fast upwards.

2.Use high-power appliances If you buy a new appliance in your home and the appliance is a high-power appliance, usually the meter in your home will run faster. If you add high-power appliances to your home, it's normal for the meter to run faster and consume more electricity.

phenomenon, please double-check whether high-power appliances have been added to the home.

3.There is a problem with the meter You can go to the power supply company to check if the meter is abnormal at home. You can also judge for yourself, unplug all the power switches and appliances in the house, connect the 100-watt incandescent cord to the meter, turn on the incandescent light for an hour, and observe the extent of the meter.

If it is kilowatt-hours, it means that the meter is normal; If it is not degrees, it means that the meter is abnormal.

The meter has a calibration button, so the speed of the meter can be adjusted, but it will not be accurate after adjustment. Therefore, it is strictly forbidden to adjust the meter without permission after calibration.

If you can open the meter cover, there are many ways to do so. For energy meters with manual meter calibration, simply changing the calibration point can make the meter slower or faster.

The electronic meter is also adjustable, but it must be removed. There is an adjustable resistor inside. It can be adjusted mechanically, but the box must be removed. The simple mechanical method is to find a fast-strength magnet and place it on the meter.

Screws with positive and negative signs on the left side of the glass of the old meter are used to adjust the speed, but have a lead seal. You can only adjust it by opening the glass cover. The minus sign adjusts slower, but the adjustment is small.

You can use the 2 small screws on the internal wiring block to pass through the cover plate, loosen the screws and stop the operation.

The appliances in the home are turned off and the meter dial is still slowly spinning (or the pulse lights are still flashing), mainly because residents think they don't have electricity but often ignore the following.

1) Electrical appliances that are not found in the standby state are still working, such as stable power supply, charger, night light, fish tank air pump and electric heating rod, cordless**, etc.

2) Although the electrical appliances are turned off, the power is still not cut off, but the electrical appliances are still in standby mode, such as air conditioners, stereos, TVs, etc.

3) Electric water heaters, water dispensers, rice cookers, etc. are in a state of insulation.

4) No other abnormalities were found, such as leakage.

The presence of these conditions allows the current loop to still flow and the energy meter to still measure.

Test for leakageOnce the electricity leaks, not only the meter will go fast, but there will also be a possibility of danger.

If there is no leakage, first cut off all electrical appliances in the home and observe the speed of the meter。If it still keeps going crazy and the electricity consumption increases, contact the power supply company to come to the door for calibration.

Even if the leakage protection switch works normally, when the switch does not trip and there is leakage, it will also make the meter rotate and consume more electricity。It is necessary to find the root cause and solve it thoroughly. Of course, if you suspect that there is a problem with the meter, you can unplug it and turn off all switches and electrical appliances, and use a 100W incandescent bulb to light it for 1 hour to test.

If there is no obvious abnormality in the speed of the meter, you can observe it for a period of time to reduce the electricity consumption at homeIf there is a lot of electricity, print the electricity bill voucher first, and then contact the relevant department for inspection.

The solution to the problem of the meter going too fast is as follows:

1. Check whether the electrical appliances consume electricity

Turn off all electrical appliances in your home, including socket switches. If the meter is going very slowly at this time. That means that the electrical appliance forgot to turn off and has been running at a higher power.

In the face of this situation, we only need to turn off the electrical appliances that we forgot to turn off, and remember to turn them off next time we use them.

2. Check whether the circuit is leaking

If you turn off the shed and all electrical appliances, and the meter still goes faster, then you have to check whether the circuit is leaking. Inspection method: The insulation resistance of the circuit in each area can be detected with a clamp meter. Especially in bathrooms and kitchens that use a lot of water, it is necessary to focus on testing.

If the insulation resistance is too low, it proves that there is leakage in the line. In this case, it is necessary to replace the line with the insulation resistance as soon as possible.

3. Check whether the meter is abnormal

Today's chain-tracking meters are all smart meters, and sometimes the meters are not calibrated, or the meters are wrong, which will also cause the meters to be abnormal. Under normal circumstances, if all the electrical appliances in the home are turned off, there is no leakage in the line.

Then you have to wonder if this is the case. In the face of this situation, we should call the service of the power grid company as soon as possible** and let the power grid company arrange for an electrician to check the meter. If it is indeed a problem with the power company, they will take care of the repair and refund the corresponding overcharged electricity bill.

Example of a workaround:

After selecting an electrical device with relatively stable power to observe the value, turn off all the electrical equipment at home, record the degree displayed by the meter, turn on an electric water heater or rice cooker for a period of time, turn off the device, and then record the degree displayed by the meter, subtract the two degrees and finally get the power of the equipment just used.

According to the power marked on the nameplate of the equipment, the power consumed by the device is compared with the amount recorded by the meter to determine whether the meter measurement is normal Precautions due to the fact that the home detection environment is not ideal, and the voltage is not the standard 220 state, there will be a high and low state.

In addition, temperature will also have a certain effect on the resistance, and the results are often biased. However, this method is not very accurate and can only be used as a reference.

Hello Kiss is happy to answer this question for you. How do you make your meter go fast? Method 1:

Use a professional instrument [electric energy meter effectiveness device] to calibrate the meter, so that the Yinzhen electronic meter can be slowed down or fastened. Method 2: Modify the pulse constant in the metering program.

Method 3: If it is a mechanical meter, use a magnet to lean next to the meter to make the turntable slow down by a quarter. Method 4:

Numerical meters with increased voltage sampling resistance run slowly; Reducing the voltage sampling resistance of the numerical meter runs faster; Reduce the resistance value of the current spline and the meter runs slowly; Increase the resistance value of the current spline and the meter will run faster. If you are more professional, you can open the case of the electronic watch and loosen the top wire above or below the center of the rotating disk, which works best with the first method. By checking the meter with the electronic meter, you can find out whether the speed of the meter is accurate, and the meter reading method mainly includes the following methods:

1. Manual meter reading: meter reading is carried out according to the display of the meter header. 2. Handheld infrared meter reader meter reading:

Handheld infrared meter reader: It is a single-chip microcomputer control system with infrared transceiver. 3. Long-distance automatic meter reading system: the so-called long-distance automatic meter reading system means that the management personnel can sit in the office of the remote meter, and apply the microcomputer through the special line brightness, wireless, power line, optical fiber, etc. as a channel to carry out meter reading and electricity management turntable type meter into the inside of the meter case, see that there is a U-shaped resistance wire inside, adjust the position of the connecting piece on the resistance wire, and change the speed of the turntable.

To open the meter cover, there is a screw on the U-shaped magnet under the large turntable, and twist it with a flathead screwdriver, the looser the screw, the slower the electric shock carries the leather table, and the tighter the screw, the faster the meter will turn.

1. The current transformer is one of the three main functions of the transformer (changing the voltage, changing the impedance, and changing the current). As long as you change the ratio of the coil to hail the trillion, you can change the output current and control the speed of the meter.

2. Changing the wiring cannot make the meter "go faster". The secondary test wiring of the current transformer can be reversed on the current transformer for 1 2 turns. The reverse winding can reduce the transformation ratio and make the table go faster.

The electricity meter at home is getting faster and faster, how to judge whether it is good or bad? The old electrician teaches you step by step, practical electrician technology!

I went to the power supply bureau to apply for meter calibration.

There is this kind of meter, and the current landlord is using the kind of electricity meter called the special meter for rental housing, which is faster than normal and illegally profiting, Shenzhen TV City Channel reported at 1 time. Now it's common in Shenzhen! Qualified meters can only be fine-tuned, and there is not much difference.

The meter is based on the principle of electromagnetic induction, and the magnitude of the magnetic force may change the speed of the turntable of the meter, or you should buy a magnet and put it near the meter to see if the turntable is fast or slow.

If you unplug all electrical appliances, the red light of the electronic watch is always on or not on, which means that you will not leave. Electricity is only used when it flickers. The electricity bill is still okay, if it is a submeter, if you suspect that it is fast, you can buy a piece yourself, dozens of dollars.

The meter at home is going faster and faster, is it the problem of the meter itself? Teach you step by step, practical electrical technology!

How many kilowatt-hours of electricity you run in your house, the electricity bureau will return it to you! My previous answer: The Electricity Bureau has a department dedicated to calibrating the meter, and you call the Electricity Bureau's 24-hour service** (95598) to request the meter to be corrected, free of charge.

The meter is to take the instrument to measure the error of your home appliance meter. The state stipulates that the error of the meter is plus or minus 2%. That is to say, it is normal for the meter to run 100 kWh, run 2 more degrees and run less than 2 degrees, and replace the meter beyond this range!

I'm here to check the meter.

As long as the electricity is used, the meter will flash, which has nothing to do with standby or not. In the same hour, if you turn on the bedroom light, it is estimated that it will not consume as much power as your computer standby. Look at the meter brand, if it is a brand meter, it will basically not happen what you said.

The energy of having a meter is not as good as charging a dime more per kilowatt-hour of electricity.

In fact, the computer is also a waste of electricity when waiting for the machine, not the landlord changed the watch for you.