According to the way of computer assembly, it can be divided into?

1. Open the chassis and install the power supply in the chassis.

2. Insert the CPU chip into the CPU socket of the motherboard, apply thermal grease, and install the heat sink and cooling fan.

3. Insert the memory module into the memory slot of the motherboard.

4. Install the motherboard in the chassis at the position of the motherboard, and plug the power cable of the power supply to the motherboard.

5. Install the graphics card on the graphics card slot on the motherboard.

6. The current sound cards are all PCI interfaces, so insert the sound card into the PCI slot.

7. Install the hard disk and optical drive in the chassis, plug the data cable into the corresponding interface of the motherboard, and connect the power cable.

8. Connect the control cable of the chassis panel with the motherboard, that is, the connection of various switches, indicator lights, and PC speakers.

9. Connect the signal cable of the monitor to the graphics card.

10. Power-on test whether the system can start normally.

1 Determine the configuration of the accessories.

2 Open the motherboard first, install the CPU cooling and memory3, put the power supply into the case, and then install the motherboard into the case.

4 Install the hard disk, graphics card, and optical drive.

5 Connect the power cord.

6 Set up the motherboard jumper.

7 Boot the system, thank you for adopting!

Computer assembly: Assemble all parts of the computer together reasonably.

1. Install the chassis, this link is mainly about the unpacking of the chassis and installing the power supply in the chassis.

2. The motherboard is an important part of the installation, install the motherboard properly in the motherboard position of the chassis, and then insert the CPU that needs to be installed in the motherboard processor socket, and also install the cooling fan.

3. The next step is to carry out the memory module.

The main installation is to insert the memory module into the memory module slot on the motherboard.

4. The graphics card is an important part of a computer, and we need to choose the right slot according to the bus of the graphics card in order to choose the right graphics card.

5. Then proceed to the sound card and driver.

The sound card is relatively simple, and the popular PCI slot on the market is selected.

As for the driver, because it involves the installation of hardware, optical drives and floppy drives.

6. Start the connection of the data cable between the chassis and the motherboard, including the installation of various cables such as indicator lights, power supply and switch cables.

7. After these are completed, you can consider closing the case cover, but because we also have to check the case problem, it is best not to cover it, and you can carry out the final work after the work is completed.

8. Connect the output device and display device, including the mouse, keyboard and monitor. And check the whole process on the side to see if there are any mistakes. If you don't start testing.

9. Power on the machine, and then the display screen starts to work normally, which also proves that the initial installation of our computer has ended.

After completing these nine steps, the basic hardware of our computer has been installed, which is considered to be the end of the hardware assembly of the computer. After that, as long as the system installation of the computer is completed, the computer will work normally and start to become our own artifact.

First, prepare the accessories to assemble the computer and a screwdriver, and remember to eliminate static electricity on your body;

Second, install the CPU and memory on the motherboard (before that, you need to set up the motherboard jumper according to the actual situation);

Third, open the chassis;

Fourth, install the power supply;

Fifth, install hard disks, floppy drives, and optical drives;

Sixth, install the motherboard;

Seventh, install the graphics card, sound card, etc.;

Eighth, connect the power cord;

9. Connect the data cable;

10th baffle plate;

Finally, close the chassis lid;

It's that simple.

Connect the keyboard and mouse: Finally, connect the main unit to the monitor, keyboard, and other components. Because assembling a computer is just assembling the console.

Let's connect the keyboard first, the keyboard interface is at the back of the motherboard, which is a round one. There is an upward marker on the keyboard plug, just plug it in this direction when connecting. This round-mouthed PS 2 mouse is plugged into the mouse jack on the top of the keyboard; If you buy an AT motherboard and don't have this round mouse jack, you have to buy a serial mouse and connect it to a 9-pin serial connector.

Connect the monitor and speaker: connect the signal cable of the monitor, connect the 15-pin signal cable to the graphics card, and connect the power supply to the host power supply or directly to the power socket. Be careful not to push too hard.

Usually the active speaker is connected to the speaker port or line-out port, and the passive speaker is connected to the speaker port.

Finally, connect the power cord of the primary chassis.

1. Disassemble the chassis and install the base plate and baffle;

2. Install the power supply;

3. Fix the motherboard in the chassis;

4、.Install the CPU in the CPU slot inside the motherboard;

5. Fix the fan above the CPU;

6. Fix the hard disk in the box and connect the power supply;

7. Fix the optical drive in the chassis and connect the power supply;

8. Connect the hard disk and optical drive to the motherboard with the hard disk data cable;

9. Insert the memory into the memory slot of the motherboard;

10. Connect the monitor and insert the data cable of the monitor into the AGP slot behind the motherboard;

11. Connect the keyboard and insert the keyboard into the keyboard socket behind the motherboard;

12. Connect the mouse and insert the mouse into the mouse socket behind the motherboard;

13. Insert the audio cable of the speaker & headphone into the audio interface after the motherboard;

14. The network card interface after inserting the network cable into the motherboard;

15. Boot test hardware;

16. Package the chassis after the test is correct;

After installing the host, don't be in a hurry to close the case cover, connect the power supply first, try to turn it on, and then close the cover, and then, there are speakers, network cables, etc., which can be wired after installing the operating system.

6. The gasket of the screws on the motherboard should be put on it, which can be anti-static.

1.Prepare your tools and accessories to eliminate static electricity from your body.

2.Install the CPU, CPU fan, and memory module on the motherboard.

3. Fix the motherboard with CPU and memory installed in the main chassis.

4、.Install the power supply on the main chassis.

5. Connect the power supply on the motherboard and the CPU fan power cable.

6. Install the hard disk and optical drive.

7. Install other boards, such as graphics cards, sound cards, network cards, etc. Most of these days are integrated into the motherboard and do not require installation.

8. Connect the signal lines such as switches and indicator lights on the panel of the main chassis.

9. Connect the power plug and data cable of each component to the motherboard, and connect the monitor.

10. Install keyboards, mice, and other equipment, and link the monitor.

11. Check the inside of the chassis last before turning on the machine. Check to see if there are any remaining screws, boards, etc. left inside. See if the cable finishing is in place.

12. Connect the power supply, power on and start up for inspection and testing.

CPU: AMD Athlonon II X2 250 (box) 350 (currently low-end mainstream).

Motherboard: Colorful Tomahawk V15 399 (CPU is cheap, so use a second-line motherboard, cheap).

Memory: Kingston 2GB DDR3 1333 105 (Mainstream) HDD: WD WD5000AAKX 500GB Blue Disk 280 Graphics Card:

Blaupunkt HD5750 512M Overseas Version 2nd Generation 599 (Cost-effective).

Chassis: Power train 517 99

Power supply: Huntkey Calm King Diamond Edition 248

Optical drive: Pioneer ***-231D 110

Display: AOC 941S 699

Total: 2889

Cost-effective configuration.

CPU Intel Core i5 2300 1200 Motherboard MSI PH67S-C43 699 (Tier 1 manufacturers, cheap) RAM Kingston 4GB DDR3 1333 205 HDD Seagate 12th Gen 1TB 32M 385

Graphics: Inzhong GTX460 1G Ice Dragon Edition 1399 (Good Heat Dissipation, Strong Performance) Recorder Pioneer DVR-219CHV 160 Monitor AOC E2243FW 980 (Cost-effective) (Samsung S22A330BW 1119) Power Supply Antec BP-430Plus 349 (80 Certified, Good Brand).

antec vp550p ￥449）

Chassis TT V3 299 (brand good).

The whole machine is 5676 ocean.

High stability, high cost performance.

Are you advertising JD.com???

What is there to say about this It's all in Jingdong.,There's no configuration recommendation there If you really need it,You can find ......

The computer accessories on Jingdong are much higher than the market price, you might as well take the computer hardware of Zhongguancun ** as the standard, the computer of about 2500 yuan can be assembled with a computer with a discrete graphics card.