How to set up file sharing with the same computer IP address

Install an ipx protocol, in the attributes of the local connection, don't say that you don't know that the protocol is installed in **.

Install a small home office network, when choosing, pay attention to a step to ask you how to connect the inter, choose not to connect the inter, press to finish, and finally do not configure, directly complete, maybe you can't understand, I said it is not good, but you boldly pretend, don't understand and then look at what I said, you know what I said. When you install the office network, there will be the name of the working group for you to fill in, all of them are the same, whatever you want, as long as they are the same. When sharing levels, select Allow access to folders and printers, which are all filled in the wizard for you in the installation of the office network.

Install LAN: IPX protocol + install office network + same gateway + same workgroup.

Don't be afraid of this IP problem, everyone does it, and telecom has no opinion.

It's also easy to share four computers.

You have all four machines connected to the route, first create a workgroup on one machine, and then add the other machines to the workgroup.

I'll take it step by step:

Right-click on "My Computer" "Properties" "Computer Name" "Change" and the last item "Workgroup" to enter a name, this is up to you, as long as all four machines are the same.

This allows for sharing.

Your MAC address is the same, then no matter which machine seems to be shared, you can only see your machine's things, the IP will be changed, you change the MAC address back, and then set the IP not to get it automatically, it's OK.

Just turn on tethering.

1. First of all, press "Windows" + "R" to open the running window, enter "Control" and click OK.

2. Click "Network & Internet", and then click "Network & Sharing Center".

<>4. Enter "and" in "IP address" and "Subnet mask" respectively.

5. Repeat this operation on another computer, press "Windows" + "R" again, open the running window, enter "Control" and click OK.

6. Find "System & Security" and click "Windows Firewall".

7. Find "Enable or Disable Windows Firewall" on the left, and check "Turn off Windows Firewall".

8. After confirming, click on a file, right-click "Properties", select "Share Bar" and click "Share".

9. Select "Administrator" and click "Share".

1. First of all, you need to set up sharing, right-click the folder you need to set up sharing, and select Properties.

2. Click to select the shared file, and set the users who can access the folder to ensure the security of the shared file.

3. Open Explorer, you need to access the address bar in the computer where you share the file.

4. Enter the "Computer Name" or "IP Address" of the computer sharing the file.

5. If it is not everyone's permission, the access user needs to provide the authorized account and password, if it is the other party's local account, please enter the "computer name (or IP address) user name" in the name, and the corresponding password to access.

6. If the other party does not set up sharing, and you have the local administrator's password and password, you can use the hidden sharing function of Windows to access it if you know the file storage path.

Taking Win10 as an example, the steps to access a LAN computer with an IP address are as follows:

1. First of all, we need to know the IP address of the computer to be accessed, press win+r to enter "cmd", and enter the "ipconfig" command in the cmd interface to get the IP address, as shown in the figure below, the IP address of a win10 system computer. The IPv4 address is the address.

2. Then come to the win10 series computer, open the network, we can see that we can't see any shared computer;

3. Enter Enter on the address bar to quickly enter the shared win10 system computer.

5. At this time, you can operate on the shared files and folders. For convenience, you can also right-click on a shared folder to create a desktop slide shortcut, or map a network drive;

Here's how:

1.First of all, write down the name of your computer Weixiangyou, and see the specific method of modifying your computer name, you can check the reference materials later.

2.Then create a new folder on the computer, it is best to create a new folder in the system disk such as D disk or E disk, so that it is convenient not to occupy the system disk space.

3.Hover over the created shared folder, right-click and select Properties.

4.Then select "Share" in the window that appears.

5.Then select Share or Advanced Sharing, here it means that Huai takes Advanced Sharing as an example, and Advanced Sharing can set custom permissions.

6.After selecting it, set the shared file name, comments, etc. in the window that appears, click Apply first, and then click "OK".

<>7.Finally, the sharing is successful, and now you can open the computer - the network can see the file you just shared.

<> ways to access shared folders:

2.Double-click today or right-click to open it.

3.Enter the administrator name of today, play, and do not need to fill in the general password.

4.At this time, you have entered today's shared disk, and you can open any file in it.

Nowadays, the computers of many enterprises are located in the same local area network, but not all computers can access the Internet, only a few can be accessed, so there is often a phenomenon of queuing up for the Internet. How to solve this problem? I have a way to do it, not very stupidly to directly interfere with the IP address of my own computer to the IP address of that machine, which will lead to a delay or IP conflict.

Here's how to do it: Here, I assume that my computer is computer A, the machine name is wxxt08, and the IP address is:, and the computer with Internet access is computer B, the machine name is wxxt18, and the IP address is:

Step 1: Query the MAC address of computer B.

There are many ways, the simplest and most direct way is to go to the B computer, in the MS DOS state, enter ipconfig all (note the space in the middle, 98 system input "winipcfg"), find the "physical address" from the display on the screen, and note the back 12 digits**, as shown in the figure below "0004230c575a".

If it is not convenient to check on the computer of nuclear destruction B, you can also use the following methods: enter "nbtstat -a wxxt18" or "nbtstat -a" in the DOS state, and the following will prompt: "Mac address 00-04-23-0c-57-5a", and also write "0004230c575a".

Step 2 Change the NIC configuration of the machine (PC A).

Because I am now using the Windows XP SP2 operating system, the following instructions are based on the XP SP2 system, and the 2K and 98 systems have been tested many times, and they are all feasible, please refer to the implementation.

Operate in order: Network Neighbor attribute, Local Connection attribute.

Select the "Configure" button behind the NIC.

Select "Advanced", check "Locally Administered Address", then select "Value", enter the 12 bits ** written in the first section in the empty box of the value, select "OK", and the second step ends.

Step 3 Make changes to the IP of the machine.

I want to do how to do IP modification interface, everyone will know it! In the following example, just change the existing "8" to "18", and do not change the other settings.

Okay, now turn on your IE and give it a try! As long as computer B doesn't have any internet restrictions, your computer doesn't have any internet restrictions! During the setup process, there is an occasional IP conflict prompt, it doesn't matter, there may be a problem with the setting, try again!

Enter the IP directly to solve the problem. Refer to the following below:

1.First of all, you need to set up hundreds of shared folders, right-click to set up shared folders, and select Properties.

2.Click Select a shared file and set the sharing permissions for users who can access the folder to ensure the security of the shared file.

3.Open Explorer to access the address bar on the computer where the shared file is located.

4.Enter the Computer Name or IP Address of the computer sharing the file as shown in the image below.

5.If it is not everyone's permissions, the access user needs to provide a privileged account and password, if it is the other party's local account, please enter the "computer name (or IP address) username" in the name, and the corresponding password can be accessed, as shown in the following figure.

6.If the other party does not set up sharing, but has the account and password of the local administrator, you can use the hidden sharing function of Windows to access it if you know the file storage path, as shown in the following figure.

How do I share files between two computers How do I transfer files from two computers?

1. Since many internal computers are in the same LAN (computers connected to the same router or switch become LAN), then we can first set a fixed IP address for each computer, such as one for and the other for the subnet mask to prevent conflicts when automatically assigning IP addresses.

2. Enable the "Guest" account on both computers. Start Menu--- Click on the logged-in user avatar --- Manage other users--- click on Guest Users - Enable Guest Users.

3. Then start --- settings--- Control Panel--- Management Tools--- Local Security Policies--- Local Policies--- User Rights Assignment, find the option to access this computer from the network, add.

guest users, if there is, they don't need it; Then see if there is a guest in this computer who refuses to access from the network, and if there is no guest, you don't need to set it.

4. Enter. --- Network & Sharing Center --- advanced sharing settings, open Home or Work, select Enable Network Discovery in Network Discovery, Enable File and Printer Sharing in File and Printer Sharing, and Turn Off Password Protected Sharing in Password Protected Sharing.

5. Set the shared folder, and then right-click on the folder you want to share--- Properties--- Sharing--Advanced Sharing--Permissions, and select "everyone".

Then add, set the permission level to "Read", and share is fine. If you want to cancel, go to "Advanced Sharing" and remove the "Sharing" checkbox.

6. Basically, as long as you can share it within a local area network, and then we need to find the file shared on the other party's computer, as long as we use win +

R combination shortcut key to open the run dialog box, and then enter the local IP address of the other party's computer in the opening, for example, the file is shared on the computer, we just need to enter after opening, and then click OK to find the shared file on the other party's computer.

Using Nut Cloud, Nut Cloud can automatically transfer files between collaborating colleagues, and you can get the latest work results of the other party at any time, and you no longer need to ask for documents and other documents. IDC has also done a related survey before, and the average time saved after using our products is calculated as 8 hours of working hours, which is equivalent to 5 hours of additional working time per employee per month.

Take the WPS 2019 version as an example:

About the advantages: get rid of the complicated local system setup, and share it in a few simple steps;

Get rid of device limitations, all systems can be viewed as long as there is a browser;

Share wherever you go (log in to your WPS account to view);

Folders can be set separately for each person's viewing permissions;

Steps: Enter Kingsoft Docs and enter it in your browser.

Log in to the WPS account, if you don't have it, you can use your mobile phone or other ways to register one;

Click on My Documents and then create a new folder;

Please click Enter a description.

4.Find the folder you just created, place the mouse and click Share;

Please click Enter a description.

5.You can invite friends to join through the link, and friends can open the link and log in to the account to join the sharing;

Please click Enter a description.

6.After the friend enters, we can enter the shared folder, on the right side, you can currently share the number of people, click to enter the permission settings, you can set someone separately can view or can;

Please click Enter a description.

Please click Enter a description.