What is the reason for the fire failure of Haier gas stove in use?

There are three main reasons for this:

1.If there is wind around the gas stove to blow the flame obliquely, the thermocouple cannot feel the temperature, and the gas stove should not be used in an environment with strong winds;

2.The cabinet is not ventilated, and the oxygen supplement of the gas stove is insufficient, resulting in the flameout, so the gas stove should be used to ensure that there is sufficient air circulation in the cabinet, and the general installation master will inform the user before installation that the diameter is not less than 5cm 2 ventilation holes, if the ventilation holes are not reserved, it is recommended that the bottom of the cabinet be slightly opened to open the gap, so that the air enters the cabinet.

3.The gas stove battery is used for 3 months and half a year, and there may be an alarm flameout, indicating that the battery is low and two No. 1 batteries need to be replaced, and the battery box is located at the bottom of the gas stove (note: the battery cap needs to be removed, and there is a yellow-red battery cap on the positive pole of the battery).

4.The blockage of the fire cover hole is an important reason for the flameout, please use a steel needle to intersperse and clean each fire hole on the fire cover one by one and clean up the surrounding position of the fire cover [focus on cleaning the fire hole opposite the white porcelain needle], and put the fire cover card in place after cleaning, without flash seams and skews, and then observe and use.

Thermocouple tops are dirty.

Solution: Please inquire about the service store or call 4006-999-999 to confirm the location of the nearest outlet, send the Haier induction cooker to the service store for inspection and maintenance, or contact the maintenance personnel for on-site maintenance.

The main reasons are: 1. It may be a problem with the pressure reducing valve of gas. 2. It may be that the battery is insufficient, or the circuit has poor contact. 3. There is also a situation that the thermocouple with feedback effect is aging, resulting in insufficient signal strength provided to the pulser, so there will be a flameout.

4. It may be that the oil temperature is too high when frying things in a frying pan, so there will be a situation where the heat will be turned off. 5. If there is an abnormality or damage to some parts, it will also cause the Haier anti-dry burning gas stove to always go out.

Suggested workaround:

1. Check the power of the battery first, replace the battery with a new one after deducting the battery, and see if the positive and negative poles of the battery box are rusty.

2. Check the problem of the pressure reducing valve, if there is a problem with the inspection valve, then you need to find a professional person to replace it.

3. Try to avoid frying things in a frying pan when using it, because this Haier anti-dry burning gas stove, if the oil temperature is too high, then it will automatically turn off.

4. If there is an abnormality or damage to individual parts, or the thermocouple is aging, in this case, it is recommended to find a professional maintenance personnel to replace it, which can solve the problem that Haier's anti-dry-burning gas stove is always turned off.

1. The problem of automatic flame-out may be due to damage to the induction needle inside the gas stove. 2. It may also be in the process of connection, if the induction pin and the connection line are faulty or short-circuited, this problem of automatic flameout will occur. 3. Whether the battery inside the gas stove is in a charged state, if there is no power, this phenomenon of automatic flameout will also occur.

Suggested solutions: 1. Because the gas stove has been used for too long, there may be damage to the induction needle inside or the problem of poor contact, which may lead to automatic flameout, it is recommended to contact professional maintenance personnel to check, if it is found that it is caused by the problem of the induction needle after disassembly, it is generally necessary to replace the new induction needle to be able to resume normal use. 2. First of all, it is necessary to check whether the connection line is damaged or broken, if it is due to the damage of the connection line, it can only be replaced by professional maintenance personnel.

3. Generally, in the process of using the gas stove, if the battery is not replaced due to the use time for too long, it is likely that the battery inside the Supor gas stove has run out of power, so you can directly buy two new batteries for replacement.

Reasons: 1. Some people are more sloppy, such as the gas stove itself is not full of gas, or there is a recharge gas meter, if it is not recharged in time, it will lead to insufficient gas volume, and the problem of gas outage will appear, so it will automatically turn off. Or because the bridge dismantler has no battery, it will also lead to the problem of automatic flameout.

2. The second reason is that in the process of use, it may be good at the beginning, but the gas stove circuit is not smooth, which will lead to insufficient gas and flameout.

Solution: 1. It is actually relatively simple to solve, the first aspect is that we need Zhaoyou to check whether the gas at home is normal. If not, we need to recharge in time, and at the same time, we must check whether the battery is charged, buckle the battery, and replace it with a battery to solve the problem.

2. In addition, in the process of using the gas stove, if there is a problem of unobstructed fall, in order to ensure the continuity of the gas, ensure the smoothness. We need to check whether the connected hose is bent or flattened, and sometimes we need to replace a gas hose to solve the problem.

There are two situations in which the gas stove automatically turns off: let go, and the fire will be extinguished; During the use of the gas stove, extinguish the fire and grind the fire.

There are three main reasons:

1.If there is wind around the gas stove to blow the flame obliquely, the thermocouple cannot feel the temperature, and the gas stove should not be used in an environment with strong winds;

2.The cabinet is not ventilated, and the oxygen supplement of the gas stove is insufficient, resulting in flameout, so the gas stove should be used to ensure that there is sufficient air circulation in the cabinet, and the general installation master will inform the user before installation, and reserve 2 ventilation holes with a diameter of not less than 5cm.

3.The gas stove battery is used for 3 months and half a year, and there may be an alarm flameout, indicating that the battery is low and two No. 1 batteries need to be replaced, and the battery box is located at the bottom of the gas stove (note: the battery cap needs to be removed, and there is a battery cap with a yellow and red key color on the positive pole of the battery).

There are many possible reasons for the flameout of Haier's integrated stove, and the following are several possible situations and solutions:

1.Incomplete cleaning of the combustion chamber: If too much grease or other impurities accumulate inside the combustion chamber, it may lead to a flameout situation. The solution is to clean regularly and make sure the cleaning is thorough.

2.Unstable gas source: If the gas source of the gas pipeline or cylinder is unstable, it will cause the stove to burn unstable and may go out. The solution is to check whether the air source is stable and pure, and replace the damaged air source equipment in time.

3.Insufficient fire: If the fire of the stove is insufficient, the combustion is not sufficient, which will lead to the occurrence of flameout. The solution is to check that the fire is sufficient, and if necessary, it can be replenished with a tool such as an igniter.

4.Burner failure: If the burner fails, such as a damaged or clogged valve, it can cause the cooktop to stall. The solution is to check if the burner is faulty, and if necessary, the burner can be replaced or repaired.

In short, there are many reasons for Haier integrated stove to go out, and if this happens, it is necessary to find the cause in time and take corresponding measures to solve it. It is best to check and maintain the stove regularly to ensure its normal and stable operation when it is used at ordinary times, so as to avoid unnecessary troubles.

Haier gas stove is generally caused by the flame-out protection circuit is not working normally, Songsui general thermocouple type flame-out protection device, flushed out need to be fired in the gas stove field, and then continue to press the ignition knob for a few seconds, and so the thermocouple is heated by the flame, the flame-out protection device can work normally.

This answer applies to Haier JZT-Q203 (12T).