What is the problem that the gas stove does not catch fire after it is ignited?

1.Power issues.

The reason why many water heaters can't be turned on is that the power supply is not in good contact, only check whether the plug of the power supply is on, and if not, unplug the plug and plug it in again.

2.Problems with hot and cold switches.

The reason why some water heaters can't turn on is that the hot and cold water switch is not in good contact, and if so, it can't ignite the fire.

3.Ignition fails.

If the water heater is turned on and there is no "click" ignition sound, it is possible that the ignition is faulty.

4.Solenoid valve failure.

The water heater has a "da-da" ignition sound, but it can't be lit, and there is no solenoid valve suction sound, which is generally a solenoid valve failure.

5.Low water pressure.

The water heater is driven by water pressure to start, and if the water pressure is low, the water heater is also turned on. Booster pumps can be installed or water pipes can be cleaned.

1.If the stove can't catch fire, first look at the hose and then look at the ignition nozzle The stove can't catch fire, first confirm whether the air source switch is open, if it is open, check whether the connecting hose is flattened or bent. If the connecting hose is also normal, check whether the ignition nozzle is on fire.

If the ignition nozzle does not ignite,..

2.Generally speaking, the normal flame of a gas stove should be light blue, and the internal flame of the flame should be clear, with a height of about 20mm, and a slight noise ,..

The gas stove is not very hot, and the gas stove has an adjustment switch. The regulator switch is not too large to turn on to the maximum flame, so the problem is usually the pressure reducing valve at the connection of the gas tank. Open the lid of the pressure reducing valve, you can generally see a cross or a word inside, you can use a screwdriver to adjust a little bit counterclockwise when the gas tank switch is turned off, not more, and then try to see if the fire is big, if the fire is not big, you can adjust it again when the gas tank is closed.

If you don't dare to get it, it's best to ask a professional to help you adjust. Try a pressure reducing valve if you can't do it.

How to turn down the fire in the middle of the gas stove if it is too big.

First determine whether the gas source is correct, if the gas source is not right, the flame will be relatively high, the normal flame is about 10 to 20 cm, if it is too big to make it smaller, as long as it is at the switch, the flame can be smallened, rotated to 90 degrees for the maximum, the starting position is in the direction of 12 o'clock, it is the most suitable direction to 8 o'clock, and the 7 o'clock position is the smallest.

How to maintain the gas stove.

1. Ensure cleanliness.

Generally speaking, the gas stove is used for electronic ignition, if it is an ignition needle when there is oil stain at this time, it is difficult to ignite, and repeated ignition may damage the ignition device, it must be cleaned, and usually in use, the food can not be too full, or it will drip onto the stove, which will also affect the electrode part. For the case of burner blockage, it is also necessary to clean it when it is done, so as to ensure that the ignition hole is unblocked, and if it is damaged, it should be repaired in time.

2. Install it correctly.

The gas stove must be installed correctly, and it can also ensure the service life, so its installation is also particularly important, first of all, the stove must be installed in a well-ventilated place, and the distance from the gas cylinder should be about 1 meter, and some flammable materials can not be placed under it.

And the stove should not be placed against the wall, and the distance should be more than 15 cm.

If the gas stove fire is too big, you can rotate the ignition button on the gas stove to the left or right to adjust the size of the flame.

There are two possibilities for a large flame:

1. The amount of air entering the damper is too much, and the air flow rate of the flame is large, resulting in the instability of the flame.

2. If the gas pressure is too large, the cross-sectional area of the flow is unchanged, and the larger the differential pressure, the greater the flow velocity; Treatment method: close the small damper, but the damper is not unlimited, so small that when the combustion oxygen is insufficient, the flame will turn red and the combustion efficiency will decrease; Reduce the pressure of the gas pipeline, adjust the pressure reducing valve of the pipeline, and appropriately reduce the pressure of the pipeline. After adjusting the pipe pressure, readjust the damper until the flame is light blue.

When the gas stove is lit, the fire is too big, this is a very normal appreciation, you can have a valve next to the gas stove, you can directly pick it, you may adjust the valve to the maximum before you feel that the red envelope is bigger, you can check it or send a **, you can go up and down to adjust it, 90, special flame size.

When the gas stove is lit, the fire is too big, and it may be because the gas is completely burned, so there is such a big fire. You can try to light a smaller one. It looks like it's a little less off-gas.

That's because you open the gas valve first and then ignite it, and you can ignite it first and then open the valve later, so that the fire won't be too big.

The fire on the gas stove has a gate, and when you fill the gas, you can have someone get it for you, and the fire will be smaller.

A large fire means that the gas pressure is large enough, but the gas stove can adjust the size of the flame.

You can adjust the size of the gas switch and the size of the choke opening.

The reason why the gas stove automatically goes off when it is on fire:

1. The power of the stove is insufficient. The power is enough to play, but not enough to keep the solenoid valve open, and it will turn off after a while, and it can be solved by replacing it with a new battery.

2. The flame of the stove is unstable and the induction needle is not burned, check whether the air source is insufficient or the wind blows the flame to cause deviation.

3. The fire hole near the induction needle is blocked, making it impossible to continue ignition.

4. Check whether the copper wire at the bottom of the stove is broken, the bottom may be broken after a long time.

Usually, gas cookers with ignition devices are difficult to ignite if the gas source pressure cannot maintain the "big fire". Therefore, the possibility that the fire will not open should lie in the blockage of the switch. Check that the gas switch outlet is not blocked, or replace the switch.

One of the reasons is that the weather is cold and the gas pressure is low; Second, it may be that the gas stove nozzle is carbonized and the ventilation is not smooth, so you can use a fine needle to pass it; You can also check whether the stove damper is too large, causing abnormal combustion.

1. The reason why the gas stove does not catch fire.

1. Whether the battery has electricity.

In the case of determining whether the gas stove has gas, ** whether the spark is weak when igniting, and at the same time listen to whether the ignition sound is weak, soft, and the discharge frequency becomes obviously slow, in this case, it is usually the battery is dead, and the new battery can be replaced. Another possibility is that the battery is in poor contact.

2. There is dirt on the ignition needle and flame-out protection needle.

Check whether the ignition needle or flame-out protection needle is covered with dirt, which may affect the ignition. If you have one, wipe it clean with a dry towel.

3. The nozzle is blocked.

If both of the above conditions are fine, you can check whether the nozzle is blocked. If there is, take out the fire cover first, and then use a thin iron wire to pass through the nozzle hole on the fire cover.

4. The ignition needle is not properly positioned.

Usually the distance between the fire needle and the fire bracket is about 4mm, and it should be aimed at the fire hole, so that the fire can be ignited.

5. The damper is adjusted too much.

If the damper of the gas stove valve body is adjusted too large, it is easy to cause the air flow from the fire hole to be too large, which will affect the electric spark. In addition, the air pressure is too high, the aging of the high-voltage line, and the damage of the microswitch will also cause the gas stove to not ignite.

In general, there are two cases, 1Ignition needle tilt: There is an ignition needle in the middle part of the gas stove, the ignition needle can play the role of ignition, the entire gas stove is on fire, if the gas stove is tilted, it can be straightened; 2.

The gas stove is out of power: There is a small mechanism under the gas stove, this is the place to replace the battery, try a new battery.

After turning on the gas stove, it is no longer lit. There are several reasons for this. The supply of natural gas was stopped. Batteries of natural gas fail. Problems inside the gas stove. This needs to be checked to rule it out.

After turning on the gas stove. If there is a phenomenon of no ignition, first see if the battery is dead, many times because the battery is not electric, so it cannot ignite. Then you need to observe or move the gas tank to see if there is gas?

Sometimes there is no gas in the gas tank. It can't catch fire.

It is recommended that you check whether the dry battery in the battery box at the bottom of the gas stove (some products do not use batteries) should be replaced, and buy a battery of the same size to replace it and give it a try. For the sake of safety, when checking and replacing the battery, do not turn on the gas first, and try to turn on the gas and ignite it only when there is a spark and normal ignition.

If the battery still doesn't work after replacement, then it may be that the ignition element is faulty, and you can find a professional to help you repair it, but you really can't find anyone to contact the gas company.

Judging from the problem that you added is a double-eye stove, one ignition, and one non-ignition, it can be ruled out that the battery is not charged, and it may be that the ignition element is faulty, and a professional is found to help repair it.

Some shops that sell stoves can also help with repairs.

First, there may not be enough gas. Second, it may be that the gas stove is broken. Third, it is possible that the gas valve of the gas tank is not open. Fourth, the switch is not in place, let's see which one you hit.

It may be that the ignition or the micro switch of the valve body is faulty, first check whether the valve body is stuck after pressing down and cannot be rebounded, if it cannot be rebounded, clean up the oil and dirt inside the valve body to see if it returns to normal, if it cannot be restored, replace the valve body; If the ignition continues after the valve body is replaced, the igniter is replaced.

It is also possible that the gas stove continues to ignite because the ignition mechanism of the stove cannot receive the flame signal. Due to the need for combustion safety, today's stoves are generally equipped with flame-out protection devices. The unit has a dual circuit, one for flame detection (attached to the ignition or combustion system) and the other for gas shut-off.

Once no flame can be detected, the ignition mechanism will continue to ignite, and if the key skin still does not receive a flame signal during the longest ignition period, the actuator will automatically cut off the gas. In the safety design, if the detection loop is disconnected, grounded, or the signal strength is insufficient, the system will treat it as no flame, or continue to ignite, or cut off the gas.

The solution to the gas stove that has been igniting:

1.Replace the gas stove switch with a new one;

2.replacement of the igniter with a new one; Pick-up.

3.Check whether the connecting wire of the solenoid valve is well connected;

4.Adjust the position of the thermocouple so that the fire temperature can affect its normal use;

5.If the flame-out protection device is broken, then replace it with a good one.

Turn small to the left and large to the right. The gas stove is generally marked with a large fire and a small fire, and the tempering button is rotated clockwise, which is a large fire at first, and the more you rotate, the smaller it becomes. As long as the switch is at the switch, the flame can be turned down, rotated to 90 degrees for the maximum, the starting position is in the direction of 12 o'clock, it is most appropriate to adjust it to 8 o'clock, and the 7 o'clock position is the smallest.

The gas stove is generally marked with a large fire and a small fire, and the tempering button is rotated clockwise, which is a large fire at first, and the more you rotate, the smaller it becomes. As long as the switch is at the switch, you can turn the flame down, rotate it to 90 degrees for the maximum, start at 12 o'clock, adjust it to 8 o'clock this direction is the most appropriate, and the 7 o'clock position is the smallest.

Hello dear, now for you to expand, the method of gas stove maintenance: to ensure that the clean gas stove is generally used electronic ignition, if it is an ignition needle at this time when there is oil stains, it is difficult to ignite, and repeated ignition may damage the ignition device, it must be cleaned, and usually in use, the food can not be put too full, or it will drip into the cleaning hall on the hidden stove, which will also affect the electrode part.

Hit ** big. It's big when it's spinning open.

Adjust the damper: The damper is the key to controlling the amount of gas entering the damper, and the amount of gas entering can be reduced by adjusting the damper, thereby reducing the size of the flame. Replace the nozzle:

If the nozzle is blocked or damaged, the flame may be too large due to the fluid channeling. Nozzles can be replaced and cleaned.

The reason is that the gas stove has exceeded its service life, and the service life of the gas stove is generally 8 years. The gas stove has a certain number of years, and if it is used for too long, there will be various problems, so you can first look at when the gas stove was purchased.

Solution: If the gas stove is used for too long, the gas stove should be replaced at this time, because the gas stove that is overage has great safety hazards. Or check whether the fire hole, micro switch, and ignition needle of the fire cover are blocked, damaged, or misplaced.

Solution: If the parts are damaged, you can buy parts to replace, or check the card meter to check whether the battery is out of power, the energy of the smart gas meter is provided by the battery, if the battery is not powered, the gas meter will close the valve, and there will be "close the valve or replace the battery" and other related prompts around the screen number.

The oil stains generated by the gas stove after a period of use not only affect the hygiene but also easily cause the gas stove to clog, so the gas stove needs to be cleaned regularly. I found a professional to repair the stove and regularly check the air tightness of the stove and air supply system with foaming agent.

Deep cleaning methods for cooktops:

Mix two spoons of white vinegar with 200 ml of warm water, and then use a sponge and an environmentally friendly loofah to dip this "hot vinegar water" to clean the stainless steel cooktop, you can make it as bright as new, mix it with 500 ml of hot water and 30 grams of baking soda, you can also use the loofah to dip it in, and easily remove the oil stain on the stove. Directly press 50 grams of baking soda into fine powder, sprinkle on the stovetop, and wipe with a cloth. You can also use coarse salt grains to clean, use a rag dipped in coarse salt for pickles, you can easily "rub" the oil stains on the stainless steel cooktop and glass cooktop, remember to wipe the salt clean, otherwise the stainless steel cooktop will be black.