How to adjust the temperature control of Juchuang 802D digital display?

In this case, you can adjust it through the control panel, or you can adjust it directly on the electronic software, which is completely possible and can achieve a very good adjustment effect.

The working principle of the intelligent digital display temperature controller is to automatically sample and monitor the ambient temperature through the temperature sensor, and when the ambient temperature is higher than the control set value, the control circuit is started, and the control backlash can be set. If the temperature is still rising, when it rises to the set overrun alarm temperature point, the overrun alarm function will be activated. When the controlled temperature can not be effectively controlled, in order to prevent the destruction of the equipment, the equipment can also be stopped by the function of tripping to continue operation.

It is mainly used in various high and low voltage switchgears, dry-type transformers, box-type substations and other related temperature use fields used in the power sector.

How to adjust the temperature control of Juchuang 802D digital display? The controls for the corresponding adjustments can be found in the system menu settings section of the system.

Go to the 802d display Shufen. The adjustment method is to pass directly through the temperature conditions through the panel.

If you say this, if you adjust the temperature, you can directly adjust it by pressing that button next to it, which is very easy.

A machine has a rectangular button, and you can increase your temperature and size by clicking on the rectangular button.

If you want to mediate the digital temperature control, you can also adjust it on some malicious valves.

Different models have different adjustment methods, if you are specific, you can still read the manual, or directly consult the original purchase of the merchant.

You can refer to the manual, which has the steps for temperature control and adjustment.

How to adjust the temperature control of Juchuang 802D digital display? I think that such a professional temperature control adjustment, you must ask a professional to adjust it, which is more assured.

will adjust the size, and whoever you ask will change.

set is the setting, the triangle up is up, the bottom is down, cool is cold, heat is hot. RST is reset. For example, if you want to heat 25 now, press set to heat, then press up to 25, and then press set again to be fine.

1. The owner must first adjust the thermostat to the ON state, and then set the appropriate temperature according to their own needs.

2. At the beginning of the normal period, you need to adjust the low point, about 20 degrees, and then slowly rise, generally to 24 degrees.

3. If the indicator light is attached to the thermostat, and it has been lit, it means that it has started to work, if the indicator light is off, it means that it is not working, and the thermostat is not turned on at this time.

4. If the home is equipped with an electronic thermostat, it comes with an LCD screen, and the upper part can be intelligently touched, which is more convenient to operate.

It usually comes with 5 buttons, two on the left can adjust the temperature, and the upper right corner can also set the mode, the normal staff will adjust it in advance, and there is no need to change it at ordinary times, and there will be a press time in the middle, if you want to time, you can use it to operate.

There is no refrigeration in asking questions.

How do you get this?

It's about the same as air conditioning.

It's really hot to ask questions.

It's okay to adjust the start temperature and stop temperature, for example, the start temperature is 25 degrees, press the corresponding button until 25 is displayed. For example, stop the temperature at 30 degrees, press the corresponding button until 30 is displayed, so that the setting is complete, and the temperature will always be between 25-30.

This may not have anything to do with the thermostat, it is because the power of the heating device of your parallel pants is too great, and after the set temperature is 100 degrees, although the heating stops, the residual heat after the heating device is powered off makes the temperature rise to 130. It is necessary to reduce the power of the insulating heat device. Pure traces.

Press and hold the setting key to set, what brand of it? --Maung Thanh refrigeration.

The following key should be the defrosting key, depending on the manual. Heze Junsheng refrigeration.

Take a look at what their instructions are, and generally he will have a beginner's guide and an instructional guide.

Does this thermostat have a manual, you look at the manual. If it doesn't work, contact the after-sales service.

If the temperature controller reaches the PID, how to adjust it? It's really not clear in this regard, but do you pick up the battery or the battery? A professional netizen, let's give you an answer!

"Look at what occasion it is used for, and the control accuracy requirements. General heating control, if the control error is required to be 5%, the measurement ratio is set to 10%, and the integration time needs to measure the time required for the controlled body in the temperature change of 5% (from -5% to 5% of the time) and the time allowed for the error of the process, generally take about 1 3 of the change time.

You first have to set a temperature, then turn it on, and the temperature will slowly rise to the temperature you set.

I have a thermostat PID. How to regulate? Ask the gods.

How do I adjust a thermostat? Please take a look at it and you will know, and you can pick out a lot of people to help you with the specific pick.

Installation method: Plug the refrigerator BAI into the temperature controller, and then plug the ZHI thermostat into the power supply. Equivalent to electric DAO

Source plug board, temperature control plate, refrigerator three rights.

Used in tandem. Then adjust the two knobs so that the pointer of the knob points to the corresponding position, and the specific time is as follows:1Summer:

Stop for 15 minutes. Transport**40 minutes.

2.Winter: 30-minute stop.

Transport**10 minutes. 3.

Spring and autumn: stop for 20 minutes, run for 20 minutes.