Can tile drill bits drill glass, what drill bits are used to drill tiles

Ceramic tiles are divided into five grades, there are excellent products, first-class products, second-class products, third-class products and other foreign products, because the price difference is large, need to be carefully compared. When purchasing, it is necessary to pay attention to whether the logo and specification and color number on the tile and the packaging box are consistent, and whether the product certificate, trademark and quality inspection label are clear. Products with a dimensional error greater than millimeters and a flatness greater than millimeters will increase the difficulty of construction and the effect after decoration is also poor.

Whether the size meets the standard can be judged by visual inspection. Place the brick on a flat surface to see if its four sides are exactly the same as the flat surface, and at the same time, see if the four corners of the tile are all right angles. The tile should be free of defects such as concave and convex, bulging and warping, and the error of the side length should not exceed millimeters, and the error of thickness should not exceed millimeters.

The detailed data should be proofread with vernier calipers) ceramic tiles with good hardness, strong toughness, and not easy to break. Use the edges and corners of the tile fragments to scratch each other, and check whether the broken fragments are fine or loose, hard, brittle or soft, whether they leave scratches, or scattered powder, if the former is the top grade, the latter is of poor quality. Good ceramic tile printing process is good pattern, pattern color is clear and consistent, the process is delicate and exquisite, and there is no obvious color leakage, dislocation, broken line or inconsistent shade.

The color of the tile should be uniform, the surface finish and flatness should be good, the surrounding rules should be regular, the pattern is complete, and four or five pieces should be extracted from a box to see if there are defects such as color difference, deformation, lack of edges and corners. You can drop water on the back of the tile to see how fast the water soaks after it spreads, generally speaking, the slower the water absorption, the greater the density of the tile; On the contrary, the faster the water absorption, the sparse density, and its intrinsic quality is superior. Usually cheap tiles, in the tile discord will be scattered some uneven black spots, especially the color contrast is dark, the color is uneven, this is these tiles to remove impurities and iron is not clean.

Select the desired diameter percussion drill bit. If you want to use expansion bolts for fixing, you need to select the hammer drill bit according to the size of the bolt you need. Generally, the nominal diameter of the bolt thread + 2 = the required drill diameter.

If you make holes larger than 10mm in the tile, it is recommended to do it in two parts. For the first time, small holes are pre-drilled with a 6-8mm diameter drill bit, and then reamed with the required diameter drill bit to ensure that the tiles do not crack.

It is necessary to punch and paste the sealing box glue, which can effectively prevent the enamel on the tile surface from being shocked and impacted during punching and punching. It can also effectively prevent the unstable holding of the drill bit, which can cause the drill bit to slip and jump away from the required hole punching position and scratch the tile glaze.

1. Mark the position of the tile to be punched with a marker pen (it is best to choose a solid part), and paste the sealing tape.

2. Use a hammer and sample punch (if you don't have it, you can use a large steel nail, remember that you must use a steel nail, also known as a cement nail, and not an iron nail) to punch out a small dot with a diameter of about 2-3mm at the mark, so that the enamel on the surface of the tile can be removed.

3. Select the required diameter impact drill bit to install the impact hammer, vertically align the punch point, give appropriate pressure to start the impact hammer, the feed should not be too large, and the slow force can penetrate the tile smoothly. After penetrating the tile, it can be forcefully fed to the desired depth.

4. After drilling the hole, select the appropriate expansion pipe to bury and fix the required installation objects with screws.

Alloy drill bits for drilling tiles can be purchased at hardware tool stores.

alloyed ones; Of course, diamond drill bits are also expensive.

One is a glass drill, and the other is a special drill tile.

Stone drill bits for tiling, the specific operation method is described below:

Tile punching needs to be prepared: clean water, stone drill bits, tape, markers.

1. First of all, mark the position of the tile that needs to be punched with a marker pen as shown in the figure below.

2. Next, use a stone drill bit to hit the tile as shown in the figure below.

3. Then take out the drill bit, and then tear off the sticker on the tile as shown in the figure below.

4. Drill a hole while pouring clean water as shown in the figure below.

I only learned today that electricians work to punch holes, and the selection of drill bits is the key, teach you a trick, and punching is really effortless.

Stone drill bits for tiling, the specific operation methods are as follows: tile punching needs to be prepared: clear water, stone drill bits, tape, markers.

Try not to use an electric hammer to punch holes in the tiles, because if you don't master the strength and skills, it is easy to break the tiles. Percussion drills are better, but first make sure that the punched part is hollow, otherwise the impact will also break the tile. It is more friendly to new hands to use a hand drill to make holes.

Borrow a slightly more powerful hand drill or rechargeable drill (the price is about 300, ** the low strength is too small). Buy a V-alloy drill bit that matches the size of the opening, it is special for hand drills, and it is only available in recent years. Ordinary $5 or more.

A V-shaped drill bit can make n holes in a general glazed brick, and a few holes can be punched in a full tile.

What drill bit to drill holes in ceramic tiles? Take a look at the image below:

Be cautious when using it!

Its name is triangular drill bit, and it is professionally made to cut holes in the top of the tile.

Tile punching is worried about being broken, look at this drill, you don't have to worry about it anymore.

The lead hidden drill for <> drill glass and the set drill for drilling tile are both diamond cutter heads, which are specially used to deal with the hard and brittle wood hidden fuel.

Nowadays, there are many household appliances, many of which need to be punched to install, such as air conditioners, water heaters, range hoods, etc., but many times, the tiles have been paved, and it is more difficult to punch holes, because if you don't pay attention, the tiles may crack, which will not only affect the ability to hold nails, but also may affect the aesthetics. So, what drill bit to use for tiling? What aspects need to be paid attention to when drilling holes in porcelain?

Let's take a brief look at it together.

First, what drill bit to use for high-stuffy tiles.

According to experts from Qeeka Home, you can use a glass drill bit or a carbide impact drill bit to hit tiles, because the tile is hard and brittle, so it is more appropriate to choose a glass drill bit, and the impact drill or electric drill is drilled by high-speed rotation, and it is easy to crack the tile if you don't pay attention to it.

Second, what aspects need to be paid attention to in tile drilling.

1. When entering the big eye of the tile naising, you need to determine the fixed expansion screw, and then determine the size of the drill bit according to the size of the expansion screw, usually the drill bit should be greater than the expansion screw 4mm, if you want to hit more than 10mm holes, you need to divide into two operations, first hit the hole that is 6 to 8mm, and then hit the hole of 10mm, so as to avoid tile cracking, at the same time, you also need to pay attention to the punching point and paste the box glue to avoid cracks on the glaze.

2. If the tile is vitrified brick, because of the high density, when punching, you can use a glass drill bit first, make a hole in the tile first, and then use an electric drill to drive into the wall, which can also reduce the probability of tile cracking, but because the surface of the tile is smooth, so when using the glass drill bit, pay attention to make an eye in the inclined direction first, or make a small pit first, so that the position of the hole will be more accurate, and it is easier to succeed.

Summary: The above about what drill bit to use for ceramic tiling, and what aspects need to be paid attention to when drilling ceramic tiles are introduced here, I hope it will help you. If you want to know more about related information, please pay attention to Qeeka Home.