The desktop computer is equipped with a DLINK router, and the laptop computer uses the land game to

You only need your router to have wireless function, and if you don't have one, change to one.

For D-Link wireless routers, the basic configuration is as follows:

1. Log in to the router configuration page.

Open the browser and enter it in the address bar, the default user name of D-Link is admin, and the password is empty.

2. After logging in, choose to manually set up the Internet connection, according to your network access type to set up, there are generally three kinds, 1) DHCP: that is, the operator only provides you with the line, no other information, plug the network cable into the computer to access the Internet, in this case, the access mode is DHCP, and then click Save;

2）static

IP: Static IP, that is, the operator provides you with IP address, subnet mask, gateway and DNS address, then you need to select the static IP method, and then fill in the above information into the router to save;

3) PPPoE: This is more commonly used, most of them are ADSL, that is, the operator provides you with a username and password, dial-up to access the Internet, then you need to choose the PPPoe method in the router, and then fill in the username and password into the router, and the following connection method selection is always.

As of now, the router can be connected to the Internet, of course, you also have to check whether your physical wiring is correct, and the incoming cable given to you by the operator should be plugged into the WAN (Internet) interface of the router.

3. Set up wireless.

In the wireless settings, you need to change the SSID (wireless network name), and then encrypt it, and it is recommended to use WPA WPA for encryption, and the password is 8 digits or more digits or more digits or letters.

DLINK wireless router to set up multiple computers to access the Internet: Set up router dialing.

How to set up the router].

Home Network Environment Cabling]:

1. There is a cat (modem): cat (modem) - router WAN port; The LAN port of the router --- computer 1 and computer 2.

2. No modem: network cable --- router WAN port; The LAN port of the router --- computer 1 and computer 2.

Computer enters the router]:

1. The computer IP and DNS settings are automatically obtained.

2. Open the browser, enter the general router address in the address bar or check the login information on the back of the router) Enter the route - enter the username and password.

The default is admin).

Set Router Dialing]:

1. In the [Setup Wizard], select [PPPoe Dialing] (some are ADSL Dialing), enter the Internet user name and password according to the prompts, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

The following factors that affect wireless transmission can be checked:

1) The wireless router and wireless network card can be placed in the range of 2-3 meters without obstacles for testing;

2) Whether there are household appliances in the same frequency band around the wireless environment, such as cordless** and microwave ovens, etc., because the wireless use of this frequency band will cause co-channel interference;

3) can try to modify the channel, according to the past practical experience, if the same channel is used by similar wireless networks, signal interference will be caused;

4) Change the default SSID to avoid conflict with other wireless networks, the SSID can be represented by English letters and numbers.

5) Modify wireless encryption.

If the abnormality persists, it is recommended to contact D-Link's after-sales service center.

Set the wireless in the wireless router to a number between 1 and 13 (not automatic), and set the transmitting frequency to 11G (not 11B g N). Then save and restart the router.

The easiest way to do this is to restore the router to its production settings, then set it up again, and follow the steps to fix the problem.

The router doesn't have to be turned off.

The first is the physical line connection of the router, the Internet port on the back side of the router is the ETH port used to connect the cat to the external network port, and the LAN port is used to connect to the computer in the local area network.

3. After logging in, click on the setup wizard on the left;

4. Click the online setting wizard under the setup wizard, and the setup wizard steps appear;

6. Select the network connection type: here we select the PPP OE dial-up user;

7. Enter the ADSL account and password and click Next (if you have a monthly subscription, you can enter it; If it's not a monthly subscription, you'll have to think about it; After entering the account password; In the future, after your computer is turned on, it will automatically dial up to access the Internet. This means that you don't have to manually connect to broadband every time. If you don't want to automatically dial up the Internet, you can leave it out here).

8. Wireless settings: select the security method wep, and select 64bit for wep encryption;

9. Click Next to complete the setting; At this point, our D-Link DI-624+A wireless router is set up, and we can access the Internet under normal circumstances.