DLINK524 router settings

If your connection is correct, type : in the address bar to enter the settings page (if you can't enter the settings page, you can consider resetting the router in a powered-on state first), follow the setup wizard all the way to set up, the key step is to copy the MAC address.

DI-524M Broadband Wireless Router Connection:

a.First, connect one end of the power adapter to the corresponding jack on the rear panel of the DI-524M, and then power it up.

The other end of the source adapter is plugged into a wall outlet or power strip. If done correctly, the front of the DI-524M.

The board power LED will be lit.

Place the cable DSL

modem power off; Some devices may not have a switch, and you will need to unplug the power adapter. Will.

DI-524M powered on, cable DSL

modem power off;

modem power off;

di-524m

Power on) to connect the Ethernet cable to the Cable DSL

Ethernet interface on the modem. After the Ethernet secure connection, give.

cable/dsl

The modem is powered on.

The modem is powered on.

di-524m

Power on) plug one end of the Ethernet cable into the WAN port on the rear panel of the DI-524M. If the connection is correct, the WAN port.

The LED indicator will light up. If the LED indicator of the WAN port does not light up, fall back to B1 and repeat the operation.

Plug one Ethernet cable into LAN port 1 on the rear panel of this DI-524M and plug the other end into the user's computing.

c.The Ethernet port on the network adapter of the machine, the computer is used to configure the DI-524M. Properly connected, the LED light of LAN port 1 will be lit.

Note: The LAN port on the DI-524M is MDI MDIX adaptive.

This means that the user can connect the LAN port of the DI-524M to a computer using a pass-through or cross-twisted pair cable. ）

A computer equipped with a wireless network card can be connected.

airplus

G wireless plug-in.

d.Bus adapter (cardbus

adapter) and DWL-G520+A

airplus

G wireless PCI adapter from the box.

When taken out, their default wireless settings allow them to connect with the router.

Setup process of the router:

1.Turn on the computer, open the browser, and enter the router in the address bar, which is written in the manual of this router).

2.A new dialog box will pop up asking for a username and password, both admin if you haven't changed them

3.Enter the username and password to enter the management interface of the router.

4.Click on the setup wizard and you will be prompted to proceed with the next design, which is basically to enter your broadband username and password. Once you've followed the prompts to complete the setup, you're ready to surf the internet.

5.If there is a second computer that needs to access the Internet at the same time, you only need to connect the computer to one port of the router's LAN with a network cable.

Will it go to the router settings interface? That's OK, the username is: admin, and there are two kinds of passwords: 1 is admin; 2 is empty, don't lose anything, this has something to do with different routers.

There is a PPPOE dial-up connection in the router.

It mainly depends on what kind of Internet access you have? If it is a telecom ADSL or something like that, it is very simple to set up, but if it is cell broadband and there is authentication software, the router is not supported.

The general router setup is very simple. The order is. Connect to LAN (external network cable interface) computer can be connected to LINK, after connecting to see if the indicator light is flashing when the link port is powered on, and see if the indicator light on LAN is flashing.

After confirming that everything is correct, enter the computer to open IE and enter the router's management web page in the address. In the setup wizard, click on the Internet and confirm after the password is set. The network properties of the computer are set to automatically get the IP option, and you can access the Internet after turning on the computer router to automatically assign the IP.

Check the local connection DNS settings.

Tietong network restricts customers from using routers to connect multiple computers to surf the Internet, and the problem can be solved by setting up routers: the principle of each router is similar, and the specific routing settings.

1. Set up the router. After entering the web settings page of the router from the desktop computer with which the MAC address is bound, select "Preliminary Settings" under "Basic Settings" in the main menu, click the "Modify" button in the "WAN Interface Type" column, and then select "Dynamic IP".

2. After saving, return to the "Preliminary Settings" page, there is a text box after the options in the "WAN MAC address" column, the content of which is the MAC address of the machine, the user can directly modify this MAC address in the text box, and fill in the MAC address of the bound network card. If you do not know the MAC address of the NIC, you can select the Clone MAC button to clone the MAC address of the current computer to the WAN port of the wireless router. Rebooting the router after saving it will take effect.

Note: Be sure to select "Dynamic IP" in "WAN Interface Type", otherwise the options to modify the MAC address of the WAN interface and clone MAC address will not appear. If you are using other access methods, such as static IP and PPPoE, you can re-enter the settings page to modify the WAN type after the above settings are completed.

3. If it's not clear, hi me.