What to do if the Ford E350 tire pressure test light is on

Replace the sensor (the pressure of the tire is not enough, the pressure of one tire is too high).

According to statistics, 70% and 80% of traffic accidents that occur on highways are caused by flat tires. Mercedes-Benz with a speed of more than 160 per hour, a good car like BMW. Puncture fatality rate exceeds 83% When oil prices are getting higher and higher, more consumers set the fuel saving point on engine power and ignore tire pressure.

If the tire pressure is too low or leaky, the friction with the ground will increase exponentially, and it will also accelerate the wear of the tire and deviate from the direction. At the same time increase fuel consumption. Because the sidewall of the tire is the weak part of the tire, when the air pressure is too low, it will be constantly squeezed and stretched, which is easy to cause fatigue failure and puncture.

Therefore, real-time monitoring of tire pressure is an important means to ensure tire safety. Through the "Auto Observation" reporter's visit to a number of car owners, it was found that they did not know the best index of tire pressure of their car tires. Normal tire pressure saves fuel.

Germany's Continental Automotive has calculated that as long as the tire inflation pressure is lower than the carmaker's recommended bar, it will consume more fuel. If tire pressure monitoring systems were installed in all cars and trucks, Europe alone could reduce CO2 emissions by 10 million tonnes per year.

It doesn't matter, his system is authorized by Ford, it's not easy to change, it doesn't matter.

The computer detects which car has insufficient tire pressure. Then see if there is a problem with the wiring, or is it a problem with the internal sensor??

There are several reasons why the tire pressure test light is on:

1. The tire is punctured and needs to be repaired.

2. The tire pressure is too high.

3. After the tire is repaired, it needs to be reset from the new air pressure.

4. The reset method is in the vehicle manual.

5. The sensor will generally not be broken (unless you go to a small tire shop to repair the tire, and the shovel blade is damaged if you don't operate properly).

Go to the 4S store and have a good check to see what the reason is.

Adjust the tire pressure to the standard tire pressure, start the engine, display the mileage interface on the dashboard, select the upper arrow from the left side of the steering wheel, a string of English letters will appear, and then press the R button above the dashboard or there is a small black button on the dashboard, it will appear, yes+, no-, and then select the plus sign on the right side of the dashboard, return after a few seconds, turn off and restart.

Excuse me, is the tire pressure light on the Ford motorhome E350 fixed? Mine also appeared, the air pressure has increased to the standard, how to reset the Xiao lamp.

Adjust the tire pressure to the standard tire pressure, start the engine, display the mileage on the dashboard interface, select the upper arrow from the left side of the steering wheel, a string of English letters will appear, and then press the R button above the dashboard or there is a small black button on the dashboard, it will appear, yes+, no-, and then select the plus sign on the right side of the dashboard, return after a few seconds, and restart after turning off Tianjin RV Hui answer.

The glove box or the steering wheel circumference.

There should be a button like an icon.

Check that there is no problem and then reset.

Adjust the tire pressure to the standard tire pressure, start the engine, display the mileage interface on the dashboard, select the upper arrow from the left side of the steering wheel, a string of English letters will appear, and then press the R button above the dashboard or there is a small black button on the dashboard, it will appear, yes+, no-, and then select the plus sign on the right side of the dashboard, return after a few seconds, turn off and restart.

Tianjin RV Hui professional interpretation of 13 Ford RV E350 tire pressure lights how to eliminate: take the computer to clear the fault code or look at your odometer to see if you can manually return.

Pacific Automobile Network] The headlights are still on after the car is turned off, probably because the headlights are not turned off. It is recommended to turn off the headlights and then turn them off to reduce unnecessary waste.

Timely maintenance of exterior lighting is crucial for drivers, as it not only affects driving comfort, but is also directly related to driving safety. It is often difficult for car owners to realize that their headlights, taillights, turn signals or parking lights are no longer working properly until they are alerted.

More often than not, the failure of the lamp is not limited to minor problems such as burnt out bulbs, rusted sockets or damaged plugs, and often requires professional diagnostic techniques to analyze the root cause of the failure.

If the headlight is damaged, it is usually replaced with a similar fixture. Some cars are equipped with high-intensity discharge headlamp HIDs, which generate a high-density light source through high-voltage arcing emissions generated by their pre-engineered electronic systems.

In order to ensure maximum safety for the driver, the headlights must be able to provide good forward illumination for the moving vehicle. Don't forget to check other light systems, such as turn signals, license plate lights, width indicators, parking lights, reversing lights, and brake lights. In addition, many vehicles also have fog lights as standard equipment or popular options, fog lights are generally installed in a lower position on the car, so they are highly susceptible to stone damage, and when maintaining them, in addition to checking the lighting system itself, cracks in the lights should not be ignored.

It is advisable to check the inlet air temperature sensor.

The cylinder pressure is insufficient, and the valve collapses.

The tire pressure warning light is on, as long as the tire pressure is supplemented, and then the alarm light can be eliminated, the specific operation steps are as follows:

1. Press the brake pedal of the car and prepare to start the engine.

2. Press the car's one-button start button to start the vehicle.

3. The instrument lights up and the power supply of the whole car is turned on.

4. Inflate all four tires to standard air pressure.

5. Press the tire pressure elimination button equipped with the car for 3 seconds to eliminate the tire pressure warning light.

1. The model is different, and the method is different.

2. Some need to be reset manually, some need to be reset by computer, some need to reset by themselves as long as the tire pressure is appropriate, and some need to be deflated and reinflated!

The reason why the tire warning light keeps on, and the solution.

How to reset the tire pressure warning light when it is on.

Either inflate or deflate, drive a little longer, and it will naturally disappear.

Tire eccentricity refers to eating tires, that is, there are one or several tires with abnormal acceleration wear on the inside or outside, which wears out particularly fast compared to other tires. It can be clearly seen when inspecting the tires.

The main causes of tire eccentricity are:

a.The four wheels are not aligned accurately, resulting in four tires that are not in the horizontal and vertical two straight lines required by the standard, so the two wheels on the same side will eat tires when they run up, or the front wheel or the rear wheel, mainly not in a straight line, the vehicle corrects itself, causing a certain part of the tire to the ground friction is abnormally increased, and the wear is accelerated.

b.Inaccurate toe-in adjustment can also lead to tire eating. The front wheel is slightly inclined to the inside at an angle, similar to the inside figure, which is the best angle for high-speed and stable driving All cars have their own toe angle, which will eat tires if this angle is not adjusted well.

c.Failure of the steering machine will also cause tire eating, deviation, etc.

d.The girder is uneven and out of shape, which will also cause tire eating, such as some accident cars, the reason for eating tires is that the girder body is deformed.

e.The air pressure of each tire is too different, and the tires of different specifications are mixed, which will also eat the tires.

Solution: There is no way to deform the girder, but to correct; The vast majority of other tires can be corrected by adjusting toe-in and four-wheel alignment.

One. The middle pattern of the tire is smoothed, which means that the tire pressure is too high. This can be the case with particularly wide tires.

If the tire has been hit with nitrogen, it is generally rarely ground in the middle, but if the air has been played, the water removal of the compressor is not good, and there is too much moisture in the air, and it is easy to have intermediate grinding.

Two. One side is smoothed, the other side is fine. Typical eccentric grinding.

In this case, there is a problem with the four-wheel alignment data, mainly because there is a problem with the toe-in, and it should be noted that it is not only the front wheel, but also the toe-in. Both the front and rear wheels have toe-in.

When the tires are eccentric, you can ventilate or redo the wheel alignment according to the situation.

Look at the posture and look at the door side lock, there is a black glue near the front card that is raised! Press it down with your hand and see! It may not be possible to use the switch!

There's another touch of a switch near the lights! You take a closer look.