Construction skills of sunshine board canopy, how to build sunshine board canopy?

1. Recognize the famous brand, which is also the most worry-free way at present, in the face of chaotic market conditions, most consumers have a feeling of dazzle, which also brings great difficulty to our purchase. Therefore, choosing a brand-name product with a higher reputation can save us a lot of time. 2. Waterproofing should be comprehensiveIn order to do everything without omission, we cannot let go of any parts that may cause water leakage, including bathrooms, floors, walls and many other parts.

Even in the basement, we have to do a good job of dealing with it to ensure that nothing goes wrong.

3. The thickness of the waterproof layer must be guaranteed According to common sense, the thickness of the waterproof layer is also an important factor related to its own service life and waterproof effect.

4. Closed water test. It is also essential to carry out this inspection work after the construction is completed.

1. First of all, check the skeleton, which must be smooth, without welding scars and burrs. The skeleton must be thoroughly dried without volatile solvents.

2. Lay the butyl waterproof tape on both sides of the skeleton to form a small sink.

3. Place the sunlight plate on the skeleton, and reserve expansion joints between the plates.

4. Press the EPDM bead at the interface between the boards.

5. Fix with self-drilling screws.

6. The middle of the width of the sunlight plate must be framed, which is fixed with a self-drilling screw sleeve button.

7. The sunlight board against the wall shall not be in direct contact with the wall, and the angle aluminum shall be fixed on the wall, and then the sunlight board shall be put into it and installed.

8. Seal the mouth with aluminum tape at the closing place of the sunshine board, and then fix the edge strip or angle aluminum.

9. First check whether the cutting size and expansion reserve of the plate are appropriate, and pay attention to leaving enough uniform expansion clearance, the calculation formula is as follows: total expansion gap = expansion coefficient * large temperature before and after local installation * plate length.

10. The part of the plate that is clamped by the profile plate in the hollow plate installation project must contain at least one rib, or the part where the edge of the plate is clamped is smaller by 20mm. Identify the UV-protected side of the surface of the board and install it facing outward, and never allow the UV-protected side to be installed inward.

Many friends will worry about the car outside and some things will be left there to be sunburned or wet once it is in the rainy season in spring and summer, so I know how worried my friends are, so please come and take a look at this. How to build our sunshine board canopy, everyone has always been very concerned about thisHow to build a sun board canopyNow there are many ways in our article, and the tenant can also learn what some precautions are.

First, the construction method of the sunshine board canopy.

1. The first step is to check the skeleton, which must be flat and free of welding scars and burrs. The skeleton must be thoroughly dried and free of volatile solvents.

2. Lay butyl waterproof tape on both sides of the skeleton to make a small sink.

3. The sunlight plate is placed on the skeleton, and the expansion joint is reserved between the plate and the plate.

4. Press the EPDM bead on the interface between the board and the plate.

5. Fix it with some screws.

6. The skeleton must be made in the middle of the width of the sunshine board, which is fixed with some screw sleeve buttons.

7. The sunlight board against the wall can not be in direct contact with the wall, fix it on the wall with aluminum, and then put the sunlight board in and install it.

8. Seal the mouth with aluminum tape at the closing place of the sunshine board, and then fix the edge strip or aluminum.

9. First check whether the cutting size of the plate and the amount reserved in advance are appropriate, and pay attention to leaving enough uniform clearance, the calculation formula is as follows: total clearance = coefficient * large temperature before and after installation at that time * plate length.

10. In the hollow plate installation project, the part of the plate that is clamped by the plate must be made less than a rib, or the part of the plate edge that is clamped is smaller. Identify the UV-protected side of the surface of the board and install it facing outward, and never allow the UV-protected side to be installed inward.

2. Precautions for sunshine board canopy.

1. First do a good job of whether the cutting size and reserved amount of the plate are appropriate, and pay special attention to leaving enough uniform expansion gap.

2. The installation part must contain at least one rib, and the part to be clamped must be at least 20mm.

3. Clarify the anti-ultraviolet side of the surface of the plate, and put the due side facing outward, and never allow the anti-ultraviolet side to be installed inside.

4. Don't let the profile clamp the protective film, but don't remove too much, so as not to damage the board surface due to operation.

5. The installation of the hollow plate slope should follow the direction of the ribs, which is conducive to the discharge of cold water.

6. After the plate is done, it should be self-checked, and it is necessary to carefully check whether there is water leakage, and the hidden danger of water leakage should be eliminated in time, and then check the appearance of the quality.

Our friends seem to have understood that there are many key points in our article on how to build a sunshine board canopy, which I hope you will take a look at and can refer to, as well as what are the precautions for sunshine board canopy.

There must be a lot of people who don't know much about the sunshine board, in fact, the sunshine board can be seen everywhere, such as in the parking garage, in the park, and in front of the restaurant. The sun panel can only provide shade in spring, and can also be used as a canopy. So let's take a look at the characteristics of the sun board canopy andSun panel canopyPrecautions for installation.

1. Characteristics of sunshine board canopy.

1. Light transmittance: The light transmittance of PC sunlight board can reach 89%, and it can even be as beautiful as glass. The UV coated board will not produce yellowing, atomization, and poor light transmission when exposed to sunlight, and the light transmission loss is only 10% after ten years, the PVC loss rate is as high as 15%-20%, and the glass fiber is 12%-20%.

2. Impact resistance: The impact strength of PC sunlight plate is 250-300 times that of ordinary glass, and 30 times that of acrylic plate of the same thickness, and 2-20 times that of tempered glass.

3. Flame retardant: The national standard GB8624-2006 confirms that the PC sunlight board is flame retardant Class B. The ignition point of the PC board itself is 580, which can self-extinguish after leaving the fire, and will not produce toxic gases when burning, and will not contribute to the spread of fire.

Therefore, it is very fire-resistant.

4. Sound insulation: The sound insulation effect of PC sunlight board is very obvious, and it has better sound insulation than glass and acrylic board of the same thickness, and the sound insulation of PC sunlight board is 5-9db higher than that of glass under the same thickness condition. Internationally, it is the material of choice for highway noise barriers.

2. Precautions for installation of sunshine board canopy.

1. First of all, we must check whether the cutting size and expansion reserve of the plate are appropriate, remember to pay special attention to leaving enough uniform expansion and Huaihe gap, and the calculation formula is as follows: total expansion gap = expansion coefficient * maximum temperature before and after local security * plate length.

2. Before installation, remember to lift the protective film around the plate by 30mm-50mm, do not let the profile clamp the protective film, but also do not remove too much, so as not to damage the board surface due to operation.

3. The part of the plate that is clamped by the pattern plate in the hollow plate installation project must have at least one rib, and the part that is clamped on the edge of the plate is at least 20mm.

4. Check whether the cutting size of the plate and the expansion reserve are appropriate, and we must pay attention to leaving enough uniform expansion clearance, the calculation formula is as follows: total expansion clearance = expansion coefficient * large temperature before and after local installation * plate length.

5. Identify the anti-ultraviolet side of the surface of the plate, and install the side facing outward, and never allow the anti-ultraviolet side to be installed inward.