What should I do if the shearing machine gets stuck? What happens if the shearing machine doesn t go

Remove the pressing rack and then turn the screws of the knife edge outside, so that the gap between the knife edges is large, and you can do it.

Shearing machine: shearing machine (English name: plateshears; guillotineshear) is a machine that uses one blade to reciprocate in a linear motion relative to the other to cut a sheet.

It is by means of the moving upper blade and the fixed lower blade, using a reasonable blade gap, to apply shear force to the metal sheet of various thicknesses, so that the plate is broken and separated according to the required size. Shearing machine is one of the forging machinery, and its main role is in the metal processing industry. Shearing machine is a kind of shearing equipment widely used in machining, which can cut steel plate materials of various thicknesses.

The commonly used shearing machines are divided into three types: flat shear, roll shear and vibrating shear. The products are widely used in aviation, light industry, metallurgy, chemical industry, construction, shipbuilding, automobile, electric power, electrical appliances, decoration and other industries to provide the required special machinery and complete sets of equipment.

Adjust the knife edge gap to the maximum and then make one cut, just one time. If the knife returns to its original position, you can take the board, if the knife does not come back, it will be difficult, disassemble the blade, hehe.

The knife edge may have become dull and the knife edge needs to be sharpened or replaced with a new one.

If the knife edge gap does not match the cut sheet material, adjust the knife edge gap to a suitable position.

The thickness of the shearing exceeds the actual allowable thickness of the shearing machine, you have to check the parameter sign of the shearing machine, if it is the allowable thickness of the parameter sign, it may be the virtual height of your shearing machine parameter sign.

The solenoid valve spool is blocked, disassemble the valve, and wash the spool.

Summary. What happens if the shearing machine doesn't go under the knife

1. The relief valve is blocked.

2. Electrical limit.

3. Foot switch, oil pump is broken.

Dear, the solution for the shearing machine not to go under the knife is as follows.

Summary. There may be several reasons why the shearing machine does not go under the knife:1

Power failure: It may be a faulty power line or damage to the motor itself, causing the motor to not function. 2.

Mechanical failure: Damage to the blade guide, malfunction of the transmission, etc., may cause the blade to fail to press down. 3.

Blade wear: If the blade is severely worn, it can cause a smooth cut or a complete inability to press down. 4.

Improper operation: If the user does not operate it correctly, such as not installing the blade properly or not placing the cutting material correctly, it will also cause the blade to not be able to press down. It is recommended to check whether the power supply, machinery, and blades are normal first, and if all of the above are normal, then check whether the operation is correct.

If the problem cannot be solved, it is recommended to contact a professional maintenance personnel for maintenance.

There may be several reasons why the shearing machine does not go under the knife: 1Power failure:

It may be that the power supply line is faulty or the motor itself is damaged, causing the motor to not function. 2.Mechanical Failure:

Damage to the silver guide rail of the blade chain, failure of the transmission, etc., may cause the blade to fail to press down. 3.Blade wear:

If the blade is worn out severely, it can cause a smooth cut or a complete inability to press down. 4.Improper operation:

If the user does not operate correctly, such as not properly installing the blade or not placing the cutting material correctly, the blade will not be able to be pressed down. It is recommended to check whether the power supply, machinery, and blades are normal first, and if all of the above are normal, then check whether the operation is correct. If the problem cannot be solved, it is recommended to contact a professional maintenance personnel for maintenance.

There is no problem with the power supply.

There may be several reasons why the shearing machine does not go under the knife:1Damaged or loose blades:

If the blade is damaged or loose, it will cause the shearing machine to not be able to cut down. You can check whether the blade is in good condition, and if you find that the blade is damaged or loose, you need to replace or tighten the blade. 2.

Motor failure: If the motor fails, it will not be able to provide enough power for the shearing machine to go down. It is possible to check if the motor is working properly, and if there is a problem with the motor, the motor needs to be repaired or replaced.

3.Controller failure: If the controller fails, you can't control the shearing machine.

You can check if the controller is working properly, and if there is a problem with the controller, the controller needs to be repaired or replaced. 4.Conveyor belt failure:

If the conveyor belt fails, it is not possible to properly transfer the sheared material to the shear zone lead domain. You can check whether the conveyor belt is running properly, and if there is a problem with the conveyor belt, the conveyor belt needs to be repaired or replaced. Hope the above answers can help you!

Dear, the very high shed is happy to answer for you: how to repair the blade of the shearing machine if it can't go down? A:

Methods and steps to accompany the oak suddenly:1In this case, you need to check the nitrogen cylinder first to see if the nitrogen is gone.

2.If there is no nitrogen, please check the leakage of the nitrogen cylinder, the general situation is that the sealing ring of the nitrogen cylinder is aging, and the chain can be sold indiscriminately by replacing the sealing ring. 3.

Then refill the nitrogen cylinder with nitrogen and increase the pressure to 6 megapascals. 4.In this way, the blade on the shearing machine can be lifted normally.

Summary. Hello The maintenance method for the blade of the shearing machine to go down is as follows: this depends on what kind of shearing machine you are, and it may be that the clutch is broken, or it may be that the shearing machine rises and returns to rely on nitrogen, or the accumulator is filled with liquid.

Plate shears (English name: plate shears; guillotineshear) is a machine that uses one blade to reciprocate in a linear motion relative to the other to cut a sheet. I hope the above is helpful to you If you are satisfied with me, please give me a thumbs up (rate in the bottom left corner) Your gesture is important to me <>

Hello The maintenance method for the blade of the shearing machine to go down is as follows: this depends on what kind of shearing machine you are, and it may be that the clutch is broken, or it may be that the shearing machine rises and returns to rely on nitrogen, or the accumulator is filled with liquid. Shearing machine (English name:

plate shears；guillotineshear) is a machine that uses one blade to reciprocate in a linear motion relative to the other to cut a sheet. I hope the above is helpful to you If you are satisfied with me, please give me a thumbs up (rate in the bottom left corner) Your gesture is important to me <>

Nitrogen return. Nitrogen return: Background technology: After shearing, the shearing machine should be able to ensure the straightness and parallelism requirements of the shear surface of the sheared sheet, and minimize the distortion of the plate.

There can be a variety of reasons why the blades of the shearing machine can't go down, and here are some common repair methods:

1.Clean the cutting machine: If the blade can't go down, it may be that the inside of the cutting machine is too dirty. At this point, the cutter can be taken apart, the accumulated grease and dust can be removed, and the bearings can be coated with lubricating oil.

2.Adjusting the blade: It may be caused by improper adjustment of the blade. Adjust the position and angle of the Toga fiber so that it is installed correctly.

3.Replace the blade: Cutting blades that have been used for too long can also affect the ability of the cutter to play with you. If the cutter blade is worn out, then it needs to be replaced with a new one.

4.Check the motor: If the motor fails, it may also cause the blade to go down and not be destroyed. Check whether the motor has a short circuit or open circuit, if you need to replace the motor, you need to find a professional maintenance personnel for repair.

It should be noted that for the repair of the cutting machine, it should be carried out by a professional maintenance personnel to ensure safety and effectiveness.

Generally, the hydraulic pendulum shearing machine relies on nitrogen return, which should be a nitrogen leak, and the problem can be solved by replacing the sealing ring of the return cylinder.