The laptop I just bought can t be connected to the Internet with ADSL? 10

I see,You can access the Internet at your brother and Suning's place,Because it shouldn't be your computer's problem,It's likely to be a telecommunications signal problem or other telecommunications equipment and other problems,You can take a look,In the case of connecting to the computer,The light of the telecom cat should be:adsl、lan、powerThe three lights are always on,If it is not lit or beating,Power is the power light,ADSL is the telecommunications problem,LAN is the network cable connection problem from the cat to the computer。

Finally, let's say,Install XP,Now many notebooks have to be set up in BIOS,Open the hard disk lock,Otherwise, you can't install XP,There is also a problem with the graphics card driver,This you can play Toshiba's after-sales service**,Because it should be 800 or something。 Ask the engineer over there and let him find it for you.

The landlord originally had two computers, then you connected the notebook alone, unplugged your desktop computer first, and saw if you could access the Internet, if you could, it was because the broadband account could only be used by one person at the same time, then you had to buy a router, set up the routing function, so that both can be used. If it doesn't work yet, it's weird. I guess you got the wrong password, you can re-enter it on your desktop to see if your password is correct.

It may be a network card relationship, and I recommend using WindowsXP instead.

The specific fixes for connecting your computer to the router and not accessing the Internet are as follows:

1. First of all, click the start button of your computer, and then open the control panel

2. Select "Network & Internet" in the "Control Panel" and click "View Network Status & Tasks".

3. Click "Change adapter settings" in the page that opens

4. You can now see that the local connection is disabled

5. Right-click to select it and click Enable, so that there will be no steps that cannot access the Internet through the router:

You copy the folder of Broadband My World on your computer to your laptop, connect the network cable, and run Broadband My World on your laptop. exe is fine.

It should be a problem with the notebook settings! What are the systems of your two computers?

The laptop has Internet access problems or IP settings conflicts.

I guess it's a problem with this Internet setting!! Let's figure it out for yourself!!

The specific fixes for connecting your computer to the router and not accessing the Internet are as follows:

1. First of all, click the start button of your computer, and then open the control panel

2. Select "Network & Internet" in the "Control Panel" and click "View Network Status & Tasks".

3. Click "Change adapter settings" in the page that opens

4. You can now see that the local connection is disabled

5. Right-click to select it and click Enable, so that there will be no steps that cannot access the Internet through the router:

Wireless routers need to be set up before they can access the Internet.

1. The bus of the broadband network is connected to the WAN port of the router, and the LAN port of the router is connected to the computer.

2. After starting the device, open the browser and enter it in the address bar to enter the wireless router settings interface. (If you can't get in, please look at the nameplate at the bottom of the router or the router instruction manual, the default settings of different models of routers are different.) ）

3. An account and password to log in to the router appear in the settings interface, enter the default account and password admin, or refer to the manual;

4. After successful login, select the interface of the setup wizard, which will automatically pop up by default;

5. After selecting the setup wizard, a window will pop up to explain that you can set the basic parameters of the router through the wizard, and click Next directly;

6. Set up step by step according to the setup wizard, select the Internet mode, usually ADSL users choose the first PPPoE, if you use other network service providers, select the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

7. Enter the account and password applied for from the network service provider, and go directly to the next step after the input is completed;

8. Set the wifi password, try to make the alphanumeric combination more complicated, and it is not easy to be rubbed off the network.

9. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

It is safe to say that there is a problem with the router settings, and you have changed two routers, there should be a possibility: you are using the wireless router that comes with the optical modem, and the gateway set by default of most people on your router is the same as the gateway of the optical modem"However, this caused a data transmission problem between the two wireless routers, which in turn caused the inability to access the Internet. Change the gateway of the router (in the LAN settings) to ", for example", it can be solved.

Another possibility is that someone else has cracked the password and login password of your wireless router and then set it up again for you. This way, you can do a factory reset, and then set it up again, taking care to change the login account and password, and wireless password.

The third possibility is: the router and the cat start at the same time, but the router starts fast, the (light) cat starts slowly, and then the data transmission will also have problems (my house is like that), you have to turn on the cat first, and wait for its data light to flash normally, and then turn on the router, and the problem will be solved.

That's a routing problem, try a different route.

Also connect to the router according to the previous method, and also select the PPPoE (ADSL) dial-up Internet method, as long as you can enter the router screen, if it appears.

The state of the WAN port is all.

Network Parameters, select LAN port settings and set the IP address to [[, and the rest of the settings remain unchanged.

Isn't the laptop XP's?,There may be some security settings that are too strict.,For example, turn off the built-in firewall.、Anti-virus software and the like.,Try again.,In addition,LZ is directly connected to the network cable to dial up.,Or use routing? If there is a route is not related to the route?,Try not to pass the route can be on?,If it's not connected to the route,Then I think it's still a problem with the machine's own security settings.,I once connected the phone to the notebook with vista.,At first, it couldn't be dialed.,There was also a number** error.,Later, I turned off Kaspersky.,Turn off the firewall.,Anyway, I'm closed for security.,I don't know which link it's a problem.,Anyway, in the end, I can connect.。

Hello. Have you configured the router?

Why do you still have a broadband connection when you connect to the router?

You can follow the manual to set up the router or follow my steps to set it up.

1. Turn off the power of the cat first, and the management IP of the cat is also This will cause you to enter the wrong settings, or you can't connect to the router.

After the router is set up, turn on the power of the cat.

2. The cable out of the cat is connected to the WAN port of the router, and the root cable is plugged into the computer at the LAN port of the router.

3. Open the browser address bar and enter or the password is generally admin or the password is empty on the back of the router.

4. Enter the router setup wizard, select the PPPoe Internet access mode, enter the Internet access and password, and set the wireless password in the security management (if the WAN port is prompted to be connected, you cannot enter the next step, please click the Internet access mode on the right, or the WAN port settings to set the Internet access mode and enter the password).

5. After the settings are completed, save and restart the router, and turn on the power switch of the cat.

At this point, the setup is complete.

Hope it helps.

If you have any questions, please ask me.

Look at the manual, dear. Enter the setup wizard.,And then follow the prompts step by step to set it up.,This thing is a fool's operation.,It's really not good, you can go down.,There will be a lot of tutorials.。。。

The following are all right, if it still doesn't work, you can see if your home network cable is not plugged into the router can still access the Internet, if it doesn't work, that's the operator's problem, not the router's problem, telecommunications somewhere is not allowed to use the router, you may have to clone the kac address.

Refer to the manual, XP, W7 have setting steps, step by step setting.

Has the router set up an account password?

The main reason is the poor quality of your router. You can check and judge in the following ways:

1. Use your computer to connect to the cat, and then use the computer to dial up the Internet. Keep trial and error, if the fault exists, it means that it is your cat or the network cable network problem. You'll have to check your cat and the network cable.

If you turn off the modem for a few minutes and then go back online, it means that your modem is aging and can't work for a long time. If you start modem repeatedly and the fault is still there, it means that there is a problem with your network, and you need to ask the service personnel of the network provider to come to the door for maintenance. If there is no fault, it means that there is a problem with your router.

2. There are several faults in the router, all of which are related to the poor quality of the router.

a. After the router is turned on for a few hours, it suddenly becomes unconnected to the network, and it needs to be restarted entirely, or it is good to turn off the power for a few minutes and then start it, which means that your router cannot work for a long time. The solution, if you want to buy a brand router, like that used by large companies, thousands or thousands of yuan, you can turn on it for a long time 24 hours; Do you want the router to turn off the power if you don't go to the Internet The router can't be turned on for a long time 24 hours, our company's is like this, you have to turn it off after work, otherwise you won't be able to access the Internet after a few days, and you need to restart.

b. After the router rests for a few hours, then dials up the Internet with the router, and still can't access the Internet. This is when you use the computer to connect to the modem to dial up the Internet directly, if you can access the Internet, it means that your router's automatic dialing ability is poor. This wireless router of my Siemens modem + routing + wireless routing sometimes has such failures, but the Internet access can be normal with the modem provided by the network company, and you can try this kind of problem:

1) Use the combined network cable, it is best not to connect more than two in parallel, and it is best to use the standard network cable divider.

2) The connection from the network cable outlet to the MEDOM and the router should not be too long and short, and at the same time, be careful not to tie it with the power cord of the computer, large electrical appliances or transformer Huoniu power adapter, but try to stay away from it. These can easily interfere with the dial-up data of the route.

3), after adopting the above methods still can not be eliminated, try to set the route not to dial, use the computer dial-up instead, especially through the router computer can dial-up. If this trick works, switch to per-computer dial-up in the future.

4) The above methods are invalid, and you can be sure that it is your routing problem, so you can only change the brand router. At least a few at $200.

Normal. Routers are all like that.

Your problem should be on the router, you double-check the IP configuration, whether it is consistent, have you set up automatic IP acquisition but do not enable DHCP service on the router? Or check if the dialing on your router is autodialing.

This is normal.

It is best to turn it off when it is not needed.

The router doesn't have to be turned off all the time.

It's good to leave it on usually.

The router consumes very little power.

Call telecom ** to 10,000 to call someone to repair.

You haven't set up your router. First of all, check if your wireless router's unlimited features are turned on, if it is not turned on. If yes, check if your router is set up correctly.

1. Check whether the network cable is connected incorrectly.

2. Whether the wireless router is set up normally, or whether there is an error.

3. If the above 2 are correct, the router is cleared, that is, there is a small hole next to the power hole of the wireless router and a needle or a sharp thing to push it (when the power supply is connected, until the router light flashes all).

4. If none of the above works, you can be sure that there is a problem with the router.

Have you set up your router to dial up?

Error 651 is really speaking: 1: There is an error in the name of the domain, (the username or password of Huai is incorrect).

2: The server does not reflect (the user port of the computer room is wrong, or the account concise branch number is not activated). 3：

** or due to overdue broadband payments.

Reasons for error 651.

1.Telecom limits the number of accounts you can use, for example, your account can be used by 4 people, and now 4 people are using it, and you dial error 691

2.You didn't disconnect after using it, at least the server side still didn't disconnect, thinking you were still using it, similar to the situation above, so error 691

Suggestion: Right-click on the broadband connection every time you turn it off, and tap Disconnect.

Don't keep stalking and dialing after the error 651, wait a few minutes and then try, if this situation keeps happening, call customer service **10000 Telecom (10060 Netcom 10050 Tietong), tell the staff that your computer error 651 can't be on, and then she asks "how much is your broadband number", tell her your account, and then she sometimes asks you who opened the account, who opened the account, and then after a few minutes she will find someone to help you get it.