Two wireless router environments Enter one environment to access the Internet How to set up a laptop

This IP is only the address inside the LAN, and the address must be re-obtained for a different LAN, for the address allocation of the LAN, it is still the 32-bit allocation method that is still used, and it is the same in **. If you want to make it easier, it's better to let the machine search automatically. Hope mine is helpful to you.

You don't need to set anything, as long as the other wireless router turns on the wireless function and does not set a password, and there is no MAC address filtering, then you just need to set up to automatically obtain the IP, and the rest does not need to be set at all, don't listen to those people talking nonsense.

You want to share the hard drive where the folder is located.

1. Plug in the router, do not connect the home network cable first, and reset the router (restore to the factory);

2. Connect the computer to any LAN port of the router and enter the setting page;

3. Set according to the dynamic IP;

4. Then set the SSID, encryption method and password;

5. Save and restart;

6. After setting up, connect the home network cable to the WAN port of the router.

1. Connect the computer to the LAN port of the router and change the IP address of the router. For example, most router addresses are, we just need to change the router IP address;

2. Turn off the DHCP function of the router in the settings;

3. Finally, connect the inbound network cable to the LAN port of the router (any one is fine), note that it cannot be the WAN port.

How to set up two routers to connect:

Method 1: Set up Level 2 routing.

1. How to connect two routers.

1. There is a cat (modem): cat (modem) - router 1wan port; Router 1LAN port --- router 2WAN port; The 2lan port of the router --- the computer.

2. No modem: network cable --- router 1WAN port; Router 1LAN port --- router 2WAN port; The 2lan port of the router --- the computer.

Second, the setting method.

Before setting, disconnect the WAN port cable of the second router and plug it in after the setting is complete.

1. Set the IP segment of the second router.

LAN port setting, if you have multiple routers, and it is the 2nd router, in order to avoid conflicts (router 1LAN port, you can change this IP to other. For example, it is modified to:

2. Set up a second router to access the Internet.

Check the IP details of the computer connected to the first router. (win+r--input, cmd--input:ipconfig all [remember: ip, mask, gateway, dns]).

Set it on the second router, and select Static IP in the Setup Wizard. Enter the IP that the 1st router does not use, and the others: mask, gateway, DNS settings are the same.

Restart your router once it's set up.

3. After restarting the router, the setting is completed, and the line of the 2WAN port of the router is reconnected to make the router 2 network normal.

Method 2: Router B is used as a switch.

1. Router A is set up normally.

2. Router B setting method:

First of all, the WAN port should be vacated, and all the wiring should be connected to the LAN port.

and disable the DHCP service on route B.

Modify the IP address of the LAN port of Route B (not the same as the network segment of Router A) and change the IP address to .

b Route settings automatically obtain the IP address, or the IP is the same as the IP of other computers surfing the Internet. The WAN port of B is connected to a LAN port of the person of the A router. No problem.

The first router IP is.

Words. That second router goes in.

Then go to the network parameter settings. Select LAN port settings. Change the address to and save it.

Finally, the setup wizard selects 2 dynamics. Other fool modes next. You can set a password.

Then an automatic router reboot will do it! Give points.! Thank you.

External network connection A router from WAN port to LAN port The rest of the wired Internet is also connected to LAN port So far, your wired computer can dial up the Internet through the computer Next, configure the router B Use a pass-through cable to connect the LAN port of A and the WAN port of B Configure B Use virtual dialing is PPPOE Enter the account password Wireless router B can be turned off and does not affect the Internet access of the wired connection.

Generally speaking, it is a conversion to an exchanger.

I don't have to turn on the guest or turn off the firewall for this method:

First, double-click to open Online Neighbors, then select "Set up a home or small office network" in the box on the left, then click "Next" until you finally select "Complete the wizard." I don't need to run the wizard on another computer", click Next, and then click Finish.

Then click "Start", select "Programs" or "All Programs", "Builder Tools", "Solve LAN Sharing", "Sharing Method: Access the machine can enter without verification" and restart it.

Then do the same settings on your LAN computer, and then restart it But if you want to see someone else's shared files, you must make sure that his computer is on, hehe or use the following method.

Right-click on my computer, click on Management, and then click on "User User Group", and click on Users, and remove all the errands in the bar.

The network card is changed through the switch, which belongs to the local area network.

About LAN Sharing Settings:

Right-click the folder to be shared, open the property Share and select "Share this folder on the network" in the "Network Sharing and Security" column, and choose whether to give the guest the permission to modify it according to your needs. Then you're OK.

Then open Neighbors and look at the workgroup computers to get into each other's shared folders.

Note that when sharing files, turn off the built-in firewall of Windows, otherwise it will prompt no permissions. The following is the solution I found online about the sharing failure, although it is copied, but I hope it will help you.

Method 1: Remove the restriction on guest accounts.

Click "Start Run", enter " in the "Run" dialog box, open Group Policyr, select "Computer Configuration Windows Settings Security Settings Local Policy User Rights Assignment", double-click the "Deny access to this computer from the network" policy, and delete the "Guest" account inside. This allows other users to use their guest account to access their computers using Windows XP over the network.

Method 2: Change the network access mode.

Open Group Policyr, select Computer Configuration Windows Settings Security Settings Local Policies Security Options, and double-click the Network Access: Sharing and Security Mode for Local Accounts policy. Local users are authenticated as guests, changed to Classic:

Local users authenticate themselves".

Now, when another user accesses a computer using Windows XP over the Internet, they can log in as their "identity" (provided that the account is already in Windows XP and the password is correct).

When this policy changes, so does how files are shared, and by enabling the "classic: local users authenticate themselves" method, we can limit the number of users who can access the shared file at the same time, and set different access rights for different users.

However, we may also encounter another problem, when the user's password is empty, access will still be denied. Originally, there was a "Account: Local accounts with blank passwords are only allowed to log in to the console" policy in the "Security Options" policy is enabled by default, and according to the principle of denial priority in the Windows XP security policy, users with blank passwords will be prohibited from accessing computers using Windows XP through the network.

We can simply deactivate this policy and solve the problem.

Your company should also have a switch, not all computers are connected to a router, so connect the computer to a switch or hub.

Set the IP address of the LAN and assign it manually. As.

Unify all computer workgroups. For example, workgroup, mshome, etc., test the connectivity between the computer and the router.

Each computer pings each other to see if it can be pinged.

Set up file or drive letter sharing, and set permissions, including Group Policy and user rights assignment.

That's about it.

First of all, these computers are all under the same working group, and the working group settings: right-click on my computer - properties - computer name - change.

If it still doesn't work, I'll send you a registry file for LAN settings and import it.

Just select Share Double-click on your online neighbor and follow the prompts to view the workgroup.