What is the form of fire pipe support and hanger?

What is the form of fire pipe support and hanger? In the case of U-bolts, how big is the angle iron used for off-duty work? How much is used and what is the form of the stent?

Summary. Requirements for the installation of fire pipe supports; Hello: I'll help you solve this problem:

1. The position must be correct, and the burial should be smooth and firm; 2. The fixing bracket and the pipeline should be tightly connected and fixed firmly; 3. The sliding bracket should be flexible, a gap of 3-5 mm should be left on both sides of the sliding bracket and the chute, and the amount of longitudinal movement should meet the design requirements; 4. The hanger and boom of the non-thermal elongation pipeline should be installed vertically; 5. The hanger and boom with thermal elongation pipeline should be offset in the opposite direction of thermal expansion; 6. The support and hanger fixed on the building structure shall not affect the safety of the structure.

Requirements for the installation of fire pipe supports; You Lu Ye is good: I will help you solve this problem: 1. The position must be correct, and the burial must be bright and firm in the morning; 2. The fixing bracket and the pipeline should be tightly connected and fixed firmly; 3. The sliding bracket should be flexible, a gap of 3-5 mm should be left on both sides of the sliding bracket and the chute, and the amount of longitudinal movement should meet the design requirements; 4. The hanger and boom of the non-thermal elongation pipeline should be installed vertically; 5. The hanger and boom with thermal elongation pipeline should be offset in the opposite direction of thermal expansion; 6. The support and hanger fixed on the building structure shall not affect the safety of the structure.

Specification of the bracket at the bend of the fire pipe.

At the bend of the fire pipeline, each bend is not less than 150mm, but not greater than 800mm, and a fixed bracket must be added, and the installation of the overhead pipe support, hanger, anti-sway or fixed bracket should be fixed firmly, and its type, material and construction should meet the design requirements of the company; 2. The designed hanger should be able to bear 5 times the weight of the bucket pipe filled with water at each support point of the pipeline, and the support point of the pipeline system should support the entire fire water supply system; 3. The support point of the pipe support should be located on the structure of the building, and this specification is how much GB.

gb50242-2002

Is there a bracket on both sides of the elbow?

Set within 1 meter on both sides of the elbow.

Fire pipe is used for fire fighting, connecting fire fighting equipment and equipment, and transporting fire fighting water, gas or other media pipeline materials; Due to special needs, the thickness and material of the fire pipe have special requirements, and red paint is sprayed to transport fire water.

The spacing of the brackets for fire pipes can be adjusted according to the actual situation of the side posture and the local building code of Tankaichai, and the general recommendation is to install a bracket every 2 to 3 meters. This spacing can ensure the stability and safety of the fire pipeline, and at the same time facilitate the maintenance and overhaul of the pipeline. However, the specific bracket spacing can also be affected by factors such as the type of building, pipe diameter, pipe material, etc., so it is best to refer to local building codes or consult a professional fire protection designer or engineer when designing or installing fire protection pipes to obtain accurate information.

The spacing of the supports for fire pipes is between meters and 3 meters.

According to the requirements of the building design code and the installation standard of the fire protection system, the spacing of the brackets of the fire protection pipe will vary, depending on the diameter and installation location of the pipe. Usually, the bracket spacing of fire pipes is between meters and 3 meters.

The firefighting pipeline system requires a lateral seismic support to be installed at 12 meters and a longitudinal seismic support at 24 meters. All air duct systems with a diameter greater than or equal to 9 meters are required to install a lateral seismic support, 18 meters to install a longitudinal seismic support, all electrical piping with an inner diameter greater than or equal to 60mm in the power system pipeline and cable tray rolling system, all cable trays with a gravity greater than or equal to 150n m, cable ladder frames, cable wire boxes, and busway require a lateral seismic support to be installed at 12 meters and a longitudinal non-impact seismic support at 24 meters.

200 meters of the distance of the pipe boom support.