How to take care of your microphone and how to care for your microphone

If you are in an area that may be humid in season, try to find a sealed box for an unsealed condenser microphone, such as a small shockproof box. Put some moisture-proof beads in it. If the desiccant is wet, it means that the moisture is too much, but it does not mean that the internal parts of the condenser microphone are also wet, because your moisture dryer is working.

Open the microphone hood, check whether the metal inner wall is wet, if not, it's OK, change to a closed box to save, if the microphone metal inner wall is wet, dry it with a hair dryer, and then connect it to the device and test it after ten minutes of power. If it's all normal, everything will be fine. 1. Anti-falling, especially pay attention not to knock down the microphone stand when the wire is pulled.

Impact may result in reduced sensitivity or even damage to a condenser microphone. 2. Rain-proof and dust-proof, rain is the natural enemy of the condenser microphone, the diaphragm of the condenser microphone will accelerate the corrosion of the metal material due to water, and will make the internal circuit wire short-circuit. Don't rush to put it in the box at the end, use a hair dryer to dry it before putting it in.

3. Use XLR plug correctly, sometimes temporarily add or replace the microphone, pick up the XLR head and pull it out and insert it violently, it is easy to twist or break the three male feet. 4. If you find that there is a problem with the fastener of the locked microphone, you must not lock it, and it is better to tie the condenser microphone directly to the microphone stand with electrical tape, rather than take risks because of its beauty. 5. Try to avoid hot-swap operation, that is to say, do not frequently unplug and plug in the condenser microphone or microphone cable when it has been energized, because large voltage fluctuations will not only affect the system, but also reduce the life of the condenser microphone.

It is recommended that you buy an independent microphone and put it directly on the table, about 20-30, the effect is good, and it is not easy to break. The headset with the headset and the microphone is always ripped around, and it is easier to break. I bought a Shuomec.

1. The best way is to remove the microphone grille. Once the grille is removed, it can be thoroughly cleaned without damaging the microphone. Most of the nasty materials attached to the grille come from the human body, so clean with clean water is enough.

2. Adding a mild detergent (such as dishwashing liquid) to the water can not only act as a mild disinfectant, but also eliminate the odor absorbed by the windproof foam. To remove lipstick and other substances stuck in the grille, use a toothbrush with soft bristles.

3. When cleaning, be sure to disconnect the power supply.

4. If the microphone has a removable battery, remove the battery before cleaning.

5. Allow the microphone to dry completely before reconnecting it to a power source or reinserting the battery.

1. The microphone is a high-sensitivity audio equipment, which must be handled gently to avoid falling from a height. Impacts may reduce microphone sensitivity or even damage.

2. Don't blow the microphone or pat his head with your hand to test the sound, the correct way to test the sound is to aim at the microphone and speak in a normal tone.

3. Pay attention to the moderate strength of the key push and pull of the microphone slippery and noisy wind, and push and pull in place. If you find that there is a lot of noise in use, the correct thing to do is to push and pull the switch again. If the contact is not good, it should be repaired as soon as possible.

4. When not in use, store the microphone in a dry and clean place, and avoid storing and using it in places with too high temperature and humidity, so as not to affect the sensitivity and timbre of the microphone.

Here's how to repair the microphone:

1. First of all, we must see whether the indicator light of the microphone is on, if not, check whether the battery holder is loose, whether the switch, and power are normal;

2. If there is no sound after the light is on, you need to gently pluck the electronic parts one by one to check whether they are loose;

3. If it still doesn't work, you need to remove the battery and send it to a professional repair shop to repair the solder joints of each electronic part one by one with a pointed soldering iron.

1. First prepare a toothbrush to sweep out the dust from the microphone of the mobile phone.

2. Prepare toothpicks, alcohol and cotton swabs for rubbing.

3. Use double-sided tape to peel off the microphone to stick the dust out.

4. Bring the machine, purchase invoice and repair card to the local mobile phone after-sales service center for cleaning.

5. Use ballpoint refills and small brushes to suck while sweeping.

You can use an alcohol-based toothbrush dipped in alcohol and gently wipe the microphone, if it's too dirty, you need to take the microphone apart and clean it.

You can use a relatively fine brush to clean the phone to gently sweep away the dust inside the microphone.

If you want to clean up the microphone, you can simply find some specialized personnel and ask them to help you clean it directly, because they are professional and will definitely know how to operate.