When does the drum washing machine close the sluice?

After the clothes are washed and taken out, turn off the water and turn off the electricity, turning off the water halfway may cause the entire laundry process to not be completed, and then call the police and wash it again.

Usage of front-loading washing machines:

1.The power plug of the drum washing machine needs to be connected and the water valve opened, which is a prerequisite for the washing machine to work.

2.Open the washing machine door by pressing the washing machine door handle with the tablet, then place the laundry in the drum, making sure to close the lid.

3.Pull open the detergent dispenser box and add the detergent or detergent.

4.Turn on the power switch of the washing machine.

5.Select the laundry mode according to the different clothing materials, adjust the knob of the control panel, and the position of the indicator light is the current laundry mode.

6.After selecting the washing mode by the knob, the water temperature, spinning speed, rinsing, pre-washing, etc. can be individually adjusted via the right button, and the parameter is changed with each button press.

7.After adjusting the parameters, you can press the start pause button to perform automatic laundry.

Note: The time or water temperature of some modes is fixed and cannot be modified, which is programmed and is normal.

The drum washing machine will add water at any time as needed during the working period, if there is no water coming in when it needs to be in, the machine will stop, so the faucet cannot be turned off during the washing process, and the water can only be turned off after the washing is over.

When the clothes are washed and the washing machine beeps to prompt you to pick up the clothes, you can turn off the water.

If the ground is wet, it may be that there is a leak in the connection of the water inlet pipe.

It will turn off automatically, so you don't need to do it. It's cool!

Summary. Dear, hello, the information I have queried for you here is as follows.

Generally, the drain switch of the washing machine is installed at the bottom of the washing machine (bonded with the lower drain port of the laundry bucket and fixed on the base of the washing machine with screws), and the upper part is connected with the drain switch knob with a pull belt, and the drain switch knob is turned on or off by hand.

How to turn off the drain switch of the drum washing machine.

Dear, hello, the information you have found here is as follows: the drainage switch of the general washing machine is installed at the bottom of the washing machine (bonded with the lower drain port of the laundry barrel and fixed on the base of the washing machine with screws), the upper part is connected with the drain switch knob with a pull belt, and the drain wide megasensitive switch knob is turned on or off by hand.

That's right.

Turn right.

After the clothes are washed and taken out, turn off the water and turn off the electricity, turning off the water in the middle may cause the whole laundry process to not be completed, and the alarm switch will be triggered.

Usage of the washing machine:

1.First of all, you need to connect the power plug of the drum washing machine, and then open the water valve.

2.Then press the washing machine door handle tablet, open the washing machine door, put the laundry into the drum, and close the lid.

3.Pull open the detergent dispensing box and add the washing liquid.

4.Turn on the power switch.

5.Select different washing modes according to the clothing material, adjust the knob of the control panel, and the position of the indicator light is the washing mode currently used.

6.After selecting the washing mode through the knob, the water temperature, spinning speed, pre-washing, etc. can be adjusted separately by the side button, and the parameters will be changed by pressing the button once.

7.After adjusting the parameters, you can press the start pause button to make it sleepy, and then the washing machine will automatically do the laundry.

The drum washing machine originated in Europe, and the washing method is designed to imitate the principle of beating clothes with a stick hammer. The drum washing machine is made of stainless steel inner barrel, mechanical program controller, phosphating, electrophoresis, spraying triple protection of the shell, and a number of bulky cement blocks to balance the huge centrifugal force generated when the drum rotates to do repetitive movement, plus the joint action of washing powder and water to make the clothes clean.

1.The power cord of the washing machine is in poor contact or the wire is aging. Check whether the power cord of the washing machine is plugged in tightly, whether the cord is damaged or aged, and if you find a problem, replace the power cord or repair the cord in time.

2.Washing machine motor failure. A faulty motor can cause excessive current, which can trigger a fuse to trip.

Check whether the motor is faulty, such as whether the motor is burned out, whether the motor is stuck, etc., if there is a problem, the motor needs to be replaced or repaired. 3.The washing machine drain is clogged.

If the washing machine drain is blocked, it will cause the washing machine to drain poorly, which will overload the motor and trigger the fuse to trip. Drains need to be cleaned to ensure smooth drainage. 4.

Electricity leakage inside the washing machine. If there is a leakage problem inside the washing machine, it can cause the circuit to be overloaded, which can trigger the fuse to trip. It is necessary to check whether there is a leakage problem inside the washing machine, and if there is a problem, it needs to be repaired in time.

The power cord of the washing machine is in poor contact or the wire is aging. Check whether the power cord of the washing machine is plugged in tightly, whether the noisy cord next to the power is damaged or aged, and if you find a problem, replace the power cord or repair the cord in time. 2.

Washing machine motor failure. A faulty motor can cause excessive current, which can trigger a fuse to trip. Check whether the motor is faulty, such as whether the motor is burned out, whether the motor is stuck, etc., if there is a problem, the motor needs to be replaced or repaired.

3.The washing machine drain is clogged. If the washing machine drain is blocked, it will cause the washing machine to drain poorly, which will overload the motor and trigger the fuse to trip.

It is necessary to clean the rough water pipes to ensure smooth drainage. 4.Electricity leakage inside the washing machine.

If there is a leakage problem inside the washing machine, it can cause the circuit to be overloaded, which can trigger the fuse to trip. It is necessary to check whether there is a leakage problem inside the washing machine stool, and if there is a problem, it needs to be repaired in time.

If you are not sure about <>the specific cause or cannot handle it yourself, it is recommended that you contact a professional appliance repairer for overhaul and repair.

Summary. Hello dear, there are many possible reasons why the drum washing machine trips as soon as it starts, and here are several common causes and solutions: Washing machine power failure:

It could be a loose plug or a poorly connected power cord. The solution is to check the plug and power cord for loose plugs and plug them back in or replace them. Washing machine motor overload:

It may be that there is a problem with the motor or transmission parts inside the washing machine, which is causing excessive load. The solution is to open the washing machine to check whether the motor or transmission parts are damaged or stuck, and need to be replaced or cleaned for maintenance.

Hello dear, there are many possible reasons for the drum washing machine to trip as soon as it starts, and the following are several common causes and solutions: Washing machine power failure: It may be that the plug is loose or the power cord is in poor contact.

The solution is to check the plug and power cord for loose plugs and plug them back in or replace them. Washing machine motor overload: It may be that there is a problem with the motor or transmission parts inside the washing machine, resulting in excessive load.

The solution is to open the washing machine to check whether the motor or transmission parts are damaged or stuck, and need to be replaced or cleaned for maintenance.

In addition, there is a failure of the control board of the washing machine: it may be that there is a problem with the control circuit board inside the washing machine, which causes the current to be too large when starting.

The solution is to replace the control lead lifting circuit board. Home circuit failure: It may be that the load of the home beam circuit is too large, and the circuit fuse trips.

The solution is to check that the home circuit load is reasonable, or to replace the fuse.

Dear, the drum washing machine trips as soon as it starts, and it needs to be checked and checked in a comprehensive and detailed manner. If the above old staring method does not solve the problem, it is recommended to ask professional maintenance personnel to come to the land to deal with it.

The washing machine tripped when it rained outside.

Is it caused by water ingress.

According to your description, it is most likely caused by water ingress, but it may also be caused by other reasons, such as short circuit of the line, electricity and failure of the machine. It is recommended to cut off the power supply first, check whether the internal circuit, motor and other components of the washing machine are normal, and check whether the wires are short-circuited and whether the contact is poor. If there is a problem with not calling the limb, you can turn on the power again and observe whether it will trip.

If it still trips, then it is recommended to ask a professional for maintenance.

I don't agree with the point from upstairs.

In the whole working process of the automatic washing machine, do not close the faucet, because the machine has an automatic water shut-off function, after the water reaches the water level, it will automatically close the water inlet valve, and it will be automatically opened when the water is rinsed, if you turn off the faucet during the working process of the washing machine, then when it comes to rinsing the water, even if the water inlet valve of the machine is opened, the machine can not enter the water, (the whole process of automatic washing machine work needs to enter the water three to four times) You need to open the faucet again (isn't it troublesome?). In this way, the requirements of full automation are not met. But if you've finished washing and taken out your laundry, you need to turn off the faucet and unplug it, which is common sense to use it safely.

If you have a double-barrel washing machine, which is not a fully automatic washing machine, then turn off the faucet after the water is finished, because non-automatic washing machines do not have the function of automatically closing the water inlet valve.

According to the washing machine provided by the landlord is an LG drum washing machine, I guess it should be a fully automatic drum washing machine.

After the washing machine stops, the inlet gate is not closed, and the water will not continue to flow. When the washing machine stops working, the inlet water pump stops working at the same time, so it doesn't continue to flow.

Please note: The inlet gate should be closed after the washing machine has stopped working. Turn off the AC power at the same time. This is how Haier washing machine after-sales greeting when I installed it in my home.