How to change the name of the computer on the Founder Restore Card 5

You can turn off the startup item in the following ways, but it will affect the boot speed.

There will be a restore card prompt when the computer is turned on (in fact, the function is not activated: turn on the computer - enter CMOS (del key) - enter CMOS password (thtfpc) - select to enter the "Integrated Peripherals" item - modify the "Onboard LAN boot ROM" item to "disable" - select F10 to save and exit - restart.

Copy the data in the hard disk to the U disk, and the low-level format of the hard disk is OK, and give it points.

Hehe, it's simple, take down the restore chip on the network card.

Look carefully, there is an interface, not solder.

1. Immediately after turning on the computer, click CTRL+H continuously;

Note: This password is only valid for the current day. Please enter and change the password immediately after receiving the password, otherwise it needs to be regenerated.

When you boot up (that is, at the moment when you have entered the CMOS), press and hold Ctrl+Home at the same time, so that you have entered the password input window of the reset card, as long as you enter the correct password to get the admin, you can set it up as you like in the future. On the question of the password: the general restore card has a default password, how to find the default password, it is very simple, go to the Internet to search for keywords"Restore card"That's it, you can generally find the default password.

The default password of the restoration card of Taiwan Yuanzhi brand is 12345678, hope.

The steps to cancel the Founder 2-in-1 Protection Card are as follows:

1. Start Disk Manager first, select Advanced Options in the red box, and press Enter, as shown in the following figure

2. After entering the Advanced Options interface, we select the Maintenance Options option in the red box and press Enter, as shown in the following figure:

3. The following driver starts to clear, don't do anything, all the data will be lost, generally 1TB hard disk may take about 12 hours, patiently wait for the progress bar to complete (in the red box) prompt, as shown in the figure below:

4. After the data is cleared, select the utilites in the red box and press Enter, as shown in the following figure

5. After entering the Utilities interface, select the locked hard disk (in the red box), and press Enter, as shown in the figure below

6. Select the processing method of the disk, do not choose the second low level format, we select the zero fill drive in the red box, press enter, as shown in the following figure:

7. Press Alt+C to confirm confirmation, as shown in the figure below

8. Prompt all data will be lost, select yes enter in the red box, as shown in the following figure:

9. The disk starts to execute the zero fill drive, and when the progress is completed, the Founder protection card will be completely uninstalled, as shown in the following figure

1. Start Disk Manger, select Advanced Options, and press Enter, as shown in the following figure

2. After entering the Advanced Options interface, we select the Maintenance Options option to enter, as shown in the following figure:

3. The following driver starts to clear, don't do anything, all the data will be lost, generally 1TB hard disk may take about 12 hours, patiently wait for the prompt of the progress bar to complete, as shown in the figure below:

4. After the data is cleared, select Utilites and press Enter, as shown in the following figure

5. After entering the Utilities interface, select the locked hard disk, and press Enter, as shown in the figure below

6. Select the processing method of the disk, do not choose the second low level format, we select zero fill drive, enter, as shown in the following figure:

7. Press Alt+C to confirm confirmation, as shown in the figure below

8. Prompt all data will be lost, select yes enter, as shown in the following figure:

9. The disk starts to execute the zero fill drive, and when the progress is completed, the Founder protection card will be completely uninstalled, as shown in the following figure

Press the Del key to enter the main BIOS interface when the computer is turned on.

1. Select the second item "Advanced BIOS Features".

2. Select the third item "Onboard Devices Configuration" in the submenu and press Enter to enter the next submenu.

3. Select the latter item "Founder Recovery Module" and set it to disabled.

4. Press F10 to appear in the Save Exit dialog box, select [OK].

Note: Some computers will display the "easysafe driver not found" prompt after turning off the 2-in-1 and cannot enter the system. This is because the 2-in-1 protection card has written boot information to the main boot area of the hard disk, and in this case, you need to rewrite the main boot record of the hard disk as follows:

Start the installation of the system with ghost, and enter the DOS state from the "DOS Enhancement and Toolset". Enter fdisk mbr under DOS and press enter (note: there is a space between fdisk and mbr), and then return to the prompt state without any prompt, and the main boot area (mbr) record of the hard disk is rewritten.

Just restart your computer.

The method of uninstalling and shielding the 2-in-1 protection card can be completely uninstalled or soft-shielded, and the third method described below is the soft-shielding method: 1Standard Edition (BIOS Edition), refresh the BIOS to solve.

2.For the standard version (hard card), unplug the 2-in-1 protection card or remove the bootrom chip on the protection card. 3.

The operation method of shielding without pulling the card and flashing the BIOS is as follows: (1) Install the underlying driver of the protection card; (2) Enter the F10 setting interface, enter "System Tools" - "Partition Information" - set the boot partition attribute to C, if the partition is A and B attributes, set the restore mode to "Do not restore". (3) Go to "System Tools" - Boot Settings - Boot Hide Menu - Hide Startup Menu.

4) Go to "System Tools" - Standby Settings - Enable Automatic Startup Operation - Specify the boot disk, and set the boot waiting time to "0" seconds.

Founder E320 student protection card uninstallation method: press the home button to enter the protection card program when booting up, type the password: founder, enter, and the uninstallation interface appears.

If it's a hardware card, it's dismantled, and if it's soft, it's turned off in the BIOS.

Normally, it's all about making changes first, and then creating progressions last.

You should also be familiar with the general method of changing the IP (local connection --properties --change IP), and there is nothing to say;

In addition, for the Founder protection card, isn't there another way to change the IP, that is, to change it when the network is cloned, and then "drive parameter update". You can give it a try.

In fact, many times the problems that arise are difficult to solve, so we will communicate and learn from each other in the future).

In the network layout - network settings - directly enter the IP and MAC addresses.