The Panasonic washing machine in the shutdown state automatically floods the washing machine

The most common water inlet in the shutdown state is that the water inlet solenoid valve is faulty, or it may be that there is a problem with the computer board, but this possibility is relatively small, the simple judgment method is: turn on the faucet with water intake, unplug the power plug, if the washing machine is still flooded, you can confirm that the solenoid valve is faulty, and the water can not be turned off (in the case of power failure, the solenoid valve is closed), and the solenoid valve needs to be replaced. The best way is, of course, to ask the manufacturer to authorize the maintenance point to repair (in fact, the maintenance point must provide services as long as it receives a maintenance request, and the vast majority of the factory headquarters can provide services, however, it is not easy to say in some more remote places), if it is really inconvenient, the maintenance point can not come to the door, you can also ask the local qualified maintenance department to charge for maintenance, and the charge depends on your local situation.

Neither of the above two will work, and you know some simple repairs, you can also repair them yourself, and you can't let the washing machine be wasted. I can teach you a lesson.

First of all, turn off the faucet, unplug the power plug of the washing machine, unscrew the plastic nut of the water inlet pipe connected to the solenoid valve of the washing machine in the counterclockwise direction, remove the water inlet pipe (even at the end of the faucet do not need to take it), and then start to disassemble the top cover of the washing machine, the top cover has a total of four screws to fix it on the box, respectively, one on the left and one on the left and right sides, the manufacturer usually uses a plastic cover slightly larger than the screw to cover the screw, and the plastic cover needs to be pried open when disassembled. The other two screws are on the back and can be removed directly. Remove the screws and then pick up the top cover, taking care not to use too much force, as the cover is still connected to the power cord and the wires to the motor and drain solenoid valve.

Carefully lift the top cover, find the solenoid valve, unplug the two wires plugged into the solenoid valve, and remove the two screws to remove the solenoid valve.

It is best to contact the local manufacturer's authorized repair department to purchase accessories, which are original. The washing machine has ** on the warranty card. If it is far away from the maintenance point and it is not cost-effective to go long distance, you can also go to other maintenance departments to buy solenoid valves of the same specification, but the quality is not guaranteed.

The steps of installation are the opposite of disassembly, but pay attention to two points, one is to remember to unplug the power plug of the washing machine during the hands-on process, because these wires are all 220V, safety first; Secondly, before fixing the top cover screws, it is necessary to check whether the wire is connected and whether the components are fixed in place, and then use water and electricity to test whether the solenoid valve can work normally, so as to avoid repeated labor, and then fix the top cover screws after normal.

1. It may be that its panel door is not closed properly. 2. If the water still enters the water when it reaches the preset water level but the wave wheel starts to run, it means that it is a problem with the water inlet valve. At this time, unplug the power supply line of the water inlet valve, if the water is still in, it means that the water inlet valve is broken, and it can be replaced.

If the water inlet stops after unplugging the power cable, it means that the computer board relay is sticking.

Recommendations and solutions:

1. The washing machine is an indispensable household appliance in life, and if there is a problem with the use of guess the world, it will also lead to frequent failures. If it is the first time to use, read the instructions carefully and follow the operating instructions. It is also necessary to pay attention to the power outlets.

It should be reasonably arranged to avoid electric shock accidents.

2. Do not place flammable or corrosive materials next to it, and it is best to put it in a ventilated and dry place. There is a lot of noise during operation, and it is necessary to check whether the ground is flat and return to the front level, and it should be used in a flat place.

3. Some consumers will use boiling water to wash their clothes, but it will also cause a sealing ring.

Deformation occurs in aging, and once there is a problem of poor sealing, the service life will be greatly shortened.

4. After washing clothes, do not close the lid, open the hatch to ventilate it and avoid bacterial growth.

5. If you can't handle the ear code yourself, you have to find a professional to deal with it.

Hello, I'm glad to reply to you, the treatment method of direct water discharge after the Panasonic washing machine enters the water: 1. First cut off the power supply, check whether the drain valve core is stuck in the power-off state, and then see whether the position of the valve core rod is in place, it is very likely that the internal spring is stuck. In this case, we should unscrew the valve cover and check whether there is something stuck inside or whether there is a part damaged, if something is stuck, just take it out, if there is a part that is broken, just replace it.

2. If the drain valve is normal, then check whether the tow bar of the tractor is easy to carry. You can directly pull the towbar back and forth with your hand to see if it is flexible to follow the movement, whether the internal spring is elastic enough, and whether it can open the drainage core. If there is a situation where it is stuck or cannot be opened, it means that the inside of the retractor is damaged and the retractor needs to be replaced.

3. If the retractor is normal, you can check whether the retractor has action to shake the drain valve for drainage in the case of power and water intake, if there is a description of the program of the computer board is out of order, the computer motherboard should be replaced. 4. There may also be problems such as the buried water level switch or the pressure that cannot sense the water level, and the failure of the water level sensor leads to drainage while entering the water. This can be solved by replacing the water level switch or the water level sensor.

5. The rupture or loosening of the water pressure conduit will also lead to failure, because there is no way to provide a pressure to water level switch or water level sensor. It can be solved by adjusting or replacing the water pressure air duct. 6. There is also to check whether there is water leakage in the central shaft, and the motor is burned out, and the motor needs to be replaced in this case.

I hope it will be helpful to you, and you can always find the teacher if you have any other questions in the future. I wish you all the best in your life.

The general situation is that the valve core of the inlet valve is stuck, and it cannot be reset after being turned on by power, resulting in water inlet all the time, and the inlet valve is replaced first; 2. If the fault is not solved, the problem lies in the water level sales section switch, the use time is long, the water level switch can stop the water ingress, causing the water inlet not to stop, at this time the water level switch should be replaced; 3. If the pressure pipe is worn and broken due to a long period of use, or the pressure pipe is in poor contact with the water level switch and the outer barrel nozzle or disconnected, causing air leakage, it can also lead to more than water ingress, because the computer board is not at the pressure and the water level switch does not work, and it is misunderstood that the water is not at the water level, at this time, the pressure pipe should be checked for wear and whether there is poor contact or disconnection at the two joints; 4. Due to the use of a long time, there is a foreign object blocking the air valve mouth, resulting in the pressure can not be transmitted to the pressure switch, at this time the big nut should be unscrewed, and then take out the inner barrel to take out the foreign body blocking the air valve. 5. If everything is invalid, you should try to replace the computer board, because all actions are controlled by the computer board.

What is the reason for the automatic start of the Panasonic wave wheel washing machine after the automatic shutdown Hello dear, 1. The washing machine will automatically switch on and off during use, the reason for this situation is that there are a lot of clothes that are put into the washing machine for washing and dehydrating at one time, if the clothes are seriously unbalanced when the dehydration is started, when the dehydration bucket starts to rotate, it will directly hit the safety switch and cause the washing machine to stop working. 2. When the dehydration starts, it is not particularly serious clothing imbalance, but in the process of high-speed rotation of the dehydration barrel, due to the action of centrifugal force, the dehydration outer barrel of the dehydration system will swing and collide with the safety lock switch, at this time, the safety interlock switch sends an electrical signal to the computer board, and the washing machine will automatically carry out the self-balancing procedure of the clothes, that is, stop the dehydration, and transfer to water injection (automatic water intake) - wave wheel swing (balance clothes) - drainage - dehydration again. 3. If the balance requirements of dehydration of clothes are not met, the washing machine will automatically carry out several self-balancing processes, and then Brother Bee will inform and automatically shut down.

Summary. The reason why the washing machine drains automatically when it is turned on:

1. There is a rupture in the drain pipe itself that causes water leakage, and it is recommended to replace the drain pipe.

2. After the drain valve is stuck by foreign objects, the closure is not tight or the drain valve is broken, you can first clean up the foreign matter at the drain valve port, if not, the spring of the drain valve is broken, and you can change the spring.

3. The central shaft leakage, the problem of central shaft leakage must be solved, otherwise the motor will soon be burned out, and the traction motor can be protected with a plastic bag.

4. It may be that the connection between the drain pipe and the washing machine is leaking, and it is recommended to reconnect it.

Panasonic washing machine opens the lid and drains water automatically.

The reason for the automatic drainage of the washing machine when it is turned on: 1. The drain pipe itself has a rupture, which causes water leakage, and Meng Rangsong suggests replacing the drain pipe. 2. The drain valve is not closed tightly or the drain valve is broken after being stuck in the foreign body, you can first clean up the foreign matter in the drain valve port, not that the spring of the drain valve is broken, and you can change the spring.

3. The central shaft leakage, the problem of central shaft leakage must be solved, otherwise the motor will soon be burned out, and the traction motor can be protected with a plastic bag. 4. It may be that the connection between the drain pipe and the washing machine is leaking, and it is recommended to reconnect it to Zhizheng.

Hope mine is helpful to you.