What should I do if the door of the Panasonic drum washing machine cannot be opened after rinsing an

Please carefully check whether there is a "reminder" posted on the door: it must take more than 2 minutes after the power is off to open the door!

There are also bold words in the manual!

There is a lid at the bottom right of the laundry door that opens, and there is a black cable, which opens when you pull hard. If the water level inside is higher than the observation window, the water will flow out. There is also a power supply that can be turned on after two or three minutes after unplugging.

As long as there is no fault alarm on the machine, there is no need to move it by itself, as long as you wait for a few minutes, it will be automatically unlocked.

When the washing machine is running, especially when the dehydration is rotating at high speed, if there is a foreign object or a hand reaching into the dehydration bucket, it is easy to damage the bucket or even hurt the hand.

In addition, the water level of the drum washing machine will slightly exceed the glass door, and if it is opened instantly, it will cause a large amount of water to overflow.

Therefore, when designing, this security door lock was intentionally added to avoid misoperation by users.

To unlock the door, the machine is set to pause or terminate the program (i.e. after the end of the laundry) for 1-2 minutes. When you hear a "click", it means that the door lock has been opened. If the program ends normally, an audible signal will be sent to inform the user that the machine is ready to be turned on.

So, don't worry, this is normal.

In addition, if it can't be opened for a long time, this is a door lock failure, so I have to call after-sales to deal with it.

The top cover safety switch is damaged: the royal sideThe top cover of the washing machine cannot be opened during the dehydration process, otherwise the dehydration process will stop immediately, which will also cause the safety switch of the top cover of the washing machine to be damaged, causing the washing machine to fail to dehydrate. Therefore, during the dewatering process, the top cover should not be opened to avoid damage to the top linkage switch.

Foreign object stuck:The washing machine can't get rid of the water, and it is very likely that a foreign object is stuck in the inner and outer barrels. It is recommended to open the top cover, dial the inner barrel clockwise by hand to try it, if it can be rotated, it proves that it is not a foreign body stuck, on the contrary, there is a foreign body, and it can be removed.

Precautions for the use of washing machines.

It should be noted that corrosive substances are not easy to be placed next to the washing machine, and flammable materials cannot be placed, so the position should be appropriate, and it is best to dry the oak air through the town.

If the washing machine is running with excessive noise, water leakage, or electricity leakage, it should be stopped immediately, the cause should be found, and the fault should be eliminated before use.

If the washing machine does not stop completely, it is best not to open the lid or reach for objects, otherwise it is easy to hurt your hands and may also cause damage to the washing machine.

Summary. Hello, the following measures can be taken.

1.Panasonic's washing machines are basically automatic door locks, and if they can't be opened after stopping, they only need to wait 1-2 minutes.

2.If you still can't open it after waiting, you can look at the manual and find a rope buckle for emergency unlocking. Generally, there is a lid open at the bottom right of the laundry door, and there is a black cable, which opens when you pull hard.

3.You can also unplug the power and wait for two or three minutes to turn it on.

4.If none of these work, you can only choose to repair.

What should I do if the door of the Panasonic drum washing machine cannot be opened.

Hello defeated Wangmo, you can take the following measures1Panasonic's washing machine is basically an automatic door lock, if it can't be opened after stopping, you only need to wait 1-2 minutes 2If the oak still can't be opened after waiting, you can look at the manual and find a rope buckle for emergency unlocking.

Generally, there is a lid open at the bottom right of the laundry door, and there is a black cable, which opens when you pull hard. 3.You can also unplug the power and wait for two or three minutes to turn it on.

4.If none of these work, you can only choose to repair.

Damn, a few cents can be cheated.

What is there to deceive, you can talk about.

Would you like to give you a few cents.

1. The reason why it can't be opened.

Drum washing machine.

With safety lock function, the lid cannot be opened when the power is on, it may be that you can't open it when the power is on; The inside of the drum washing machine has a heat.

element, when the door is closed, the heating element heats up, the bimetal sheet is heated and bent, and the main power supply is turned on and the door lock is locked. After some time after the power failure, the bimetal plate cools down and resets. It may be that the heating element is damaged, resulting in the door not being opened; A malfunctioning electric door lock in a drum washing machine can also cause the washing machine door to not open.

2. The solution that can't be opened.

You can open the door by patting the lid handle with your hand and resetting the plastic pin by vibrating. If the knob is screwed to the stop gear and the door still can't be opened for a long time, you can screw the knob to any gear again, and after a few seconds, you will hear the sound of the door lock "popping", and then the door can be opened.

There is also an emergency switch in the lower right corner of the machine, open the cover on the outside of the drain pump in the lower right corner, you will see a red plastic cable, pull down along the vertical direction of the cable, you will hear the slight sound of the door lock, and you can also open the door. It should be noted that if there is water in the bucket or the temperature is too high, the door will not be opened. The bucket needs to be filled with water.

Drain it first and then solve it through the above methods.

The general drum washing machine has an electric lock protection device, and the washing machine still belongs to the protection period for two or three minutes after the power is off, and the door lock will not be opened. So we don't rush to open the door after the washing machine stops working, just turn it on again after three or five minutes.

When everyone's drum washing machine door can't be opened, you can try the method introduced above, if it still doesn't work, you can go to the after-sales service of the washing machine, consult a professional to solve the problem.

The door of the washing machine makes Wang Da can't open it, how can I do it?

Summary. No water.

1. Turn on the power supply, the ears are close to the water inlet valve for "buzzing" sound, if so, check whether the tap water is cut off, close the faucet, screw out the water inlet pipe joint to check whether the filter screen of the water inlet valve is blocked by foreign objects, and if there is a pull out of the filter screen for cleaning. If the problem is not solved, the inlet valve should be replaced, and the valve core of the inlet valve may be stuck and cannot be opened.

2. If the water inlet valve does not have a "buzzing" sound, you should try to replace the computer board at this time, and the problem may be on the computer board.

The buttons of the Panasonic drum washing machine are normal, but the laundry is all out of control, and there is no water ingress, dehydration, laundry, and even the door can't be opened.

1. Turn on the power supply, if there is a "buzzing" sound near the water inlet valve, if so, check whether the tap water is cut off, close the faucet, screw out the water inlet pipe joint to check whether the filter screen of the water inlet valve is blocked by foreign objects, and if there is a pull out of the filter screen for cleaning. Or tell that if the question has not been solved, the inlet valve should be replaced, and the valve core of the inlet valve may be stuck and cannot be opened. 2. If the inlet valve does not have:

buzzing", at this time you should try to replace the computer board, the problem may be on the computer board.

1. First check whether the adjusting rod nut on the drain valve is loose, resulting in the tractor being unable to open the drain valve core and causing non-drainage, and fix the nut at this time so that it can open the drain valve core. Check that the tractor cable is not loose from the drain valve. 2. If the nut is not loosened or the cable is not loosened, the retractor may be damaged and the drain valve core cannot be opened, and the retractor should be replaced at this time.

3. There may be debris blocking in the drain valve and causing non-drainage, at this time, unscrew the drain valve cover first, and take out the debris. 4. If it has not been solved, the computer board may be damaged and the computer board should be repaired or replaced.

1. Do not dehydrate 1, first check the safety switch in the cover, the washing machine is turned on and the program is adjusted to the dehydration state, press the safety switch brake arm to the lowest with your hands or tools, if the computer board alarms and the digital tube shows "E1", the safety switch or computer board stove pin should be replaced. 2. If the safety switch brake arm can be dehydrated normally after pressing it with hands or tools, it means that the power-off distance of the safety switch is low, and the safety switch should be replaced at this time. 3. If in the dehydration state, only the wave wheel rotates and the inner barrel does not rotate, at this time should check whether the traction 3 has separated the pawl and ratchet wheel of the Huai clutch, if not, it is possible that the adjusting rod nut on the drain valve is loose and worn, resulting in insufficient opening distance, at this time, the distance of the adjusting rod should be readjusted, so that it can separate the pawl of the clutch and the ratchet.

If you can't solve this problem yourself, you can contact the relevant maintenance personnel to help you deal with it.