What is the reason why the printing press computer wave door has been walking?

The computer wave door of the printing machine is always walking, and the speed of the paper roller motor is fast and slow.

Phenomenon: In the process of paper threading, the speed of a paper roller motor is fast and slow, while the speed of other motors is normal.

Analysis: AMK inverter consists of three modules: power module, control module and digital inverter module. The fieldbus of the control module receives various command information, and then calculates the result to the digital inverter module, and the digital inverter module controls its internal thyristor circuit by the operation result, changes the current frequency of the control motor, and makes the motor to the required speed.

The above working principle of the inverter can be speculated that the causes of this failure may be as follows: the operation error of the control module, the failure of the digital inverter module, the failure of the motor encoder and the error of the feedback speed.

Troubleshooting: First easy and then complex principle, first replace the sercos card on the control module, the fault is still the same, and then replace the digital inverter module, troubleshooting.

I don't know if the wave door you are referring to is a launch protection window.

The general pulse Doppler radar system theoretically needs to transmit a rectangular pulse signal, the generation of this signal is not sudden appearance and disappearance, it needs a rising and falling edge, and at the same time, at this stage, the system transmits and receives conversion, and needs to give the hardware a charge and discharge conversion time, otherwise it will burn the receiver and cause interference.

As for why it is a pulse time, you can simply think that it is related to the ability of the system, and the ability to generate a signal in 1ms proves that the system can complete the transmission and reception conversion in 1ms.

If the printing press and the computer broadcaster are always walking, it is because it is in emergency operation, so it must be moved.

The printing press is always moving around in the process of computer printing because the printing press is cooling down and needs to be cooled down by activity.

The electroencephalogram of the printing press keeps going further, which may be that the signal is unstable, so it will go up and down and not move.

Reasons and solutions for inaccurate and inaccurate color registration of printing presses: 1. The paper shrinks seriously in printing, resulting in inaccurate overprinting. Paper is one of the indispensable raw and auxiliary materials for paper printing.

Due to the influence of external temperature and humidity, coupled with improper control of temperature and humidity in the printing workshop, it has a certain impact on the dryness and wetness of the paper. The temperature of the drying chamber of each color group during printing.

The printing press, the computer broadcaster has been walking, probably because you've been operating him, putting all the words he's probably been on the go.

The printing press, the computer broadcaster has been walking, what is the reason for this reason, it may be due to the computer that, the control, the assembly problem.

What is the reason that the printing press, the computer broadcasters have been walking? The reason why the printing press and computer broadcasters have been walking is probably because he has a malfunction or he. The computer broadcasters can't control it, the controller is broken or what is the reason, please ask a professional person to take a look, or consult the after-sales customer service.

The reason why the printing press and computer broadcaster went again and again was that he was always working.

Widely used in the short board printing market, such as fast printing shop, digital proofing, etc., mature commercial printing, packaging printing or rarely apply digital printing machine, mainly the cost of consumables of digital printing machine has no advantage, for large amount of printing, traditional offset printing in the cost of consumables is very advantageous, the amount of digital printing machine can be printed, no need to make plates, so personalized printing has advantages, in the equipment purchase price, traditional offset printing machine is much more expensive than digital printing machine.

There are various reasons for failures, and they need to be inspected, tested and judged step by step from the outside to the inside, from mechanical to electrical, and from software to hardware. But it is more important to pay attention to prevention and improve the bad ones.

Hello, this press, you can turn it off and restart it, it usually doesn't work like this.

If there is a problem in the computer department of the game, it is recommended that you can find relevant after-sales personnel to help you install and repair it in time.

Many things are not difficult to operate on the spot, and it is not easy to explain them here.

Computer printing design is printing plate making, before the early nineties of the last century, printing plate making was made by hand, and later there was computer design software Photoshop, Coreldraw, Adobe Illustrator, Freehand and other software, printing plate making is completed by these software.

The computer-made version is not called a typeset, but should be called typesetting in a strict sense. Printing plate making is a general concept, including the above-mentioned computer plate making, which is usually called printing by printing houses.

Plate making is for printing. There are many ways to make plates, and computer plate making is only one of the ways of plate making, plate making is for a variety of printing, and different plate making methods will have different plates, so as to correspond to different or the same printing methods. But platemaking is for printing, so printing platemaking is a big headline.

Just like running is a big headline, and running fast and jogging are subheadings.

Hello answer. The printing cost of plastic bags refers to the ink and printing costs you use in the printing process, while the printing cost of plastic bags refers to the cost of making printing layouts after the design of plastic bags is completed. This one is different.

Like now, many printers no longer need to make plates, and they can be printed directly, and the plate-making fee refers to the cost of making a printing layout after the design of the plastic bag is completed. The printing fee is the cost of the printing process.

On the contrary, the Transcend UV flatbed printer can be personalized at any time with personalized patterns with bright and vivid colors. In particular, the gradient effect cannot be achieved by traditional printing processes.

Intel Core i5-2300 (Case).

intel h61

Ӱ GT430 1G

Kingston 4G DDR3 1333

Huntkey 300W

Twin delphinium optoelectronics kit.

Host!

Motherboard: MSI A790

cpu：amd640x4

Memory: 4G 1333 DDR3

HDD: 500GB (Western Digital is recommended, Seagate Hitachi has a high repair rate) Graphics card: Yinglax: GT450 1G

Optical drive: Pioneer***

Power supply: Great Wall 500W (rated 400W, relatively stable for the computer) By the way, AMD4 core is the king Everything else is floating clouds,,I can't compare to my AMD 5000+CPU on the core overclocking directly in seconds i5,I don't believe it, try it,AMD4 core is super stable and cost-effective。

Why does the i5 upstairs use version 61? Go on the 67th edition, don't explain! That's pretty much it!

To be honest, PC notebooks, LCD monitors are average, color display and printed products must be very different, of course, PC desktops are also varied, if you want to display similar to the finished product, you must have a good graphics card, and display (ViewSonic is good), and then you need to have color correction software to help. Otherwise, it won't work.

Now Apple's desktops and laptops are good, but they are more expensive.

According to your situation, I suggest: you spend 200-300 yuan to buy a chromatography, refer to the chromatography when mixing and matching, and then compare proofs and adjust it, which is basically the same. Do this process a few more times, and you will naturally have a number in mind.

Please take a look at the paper lead to the future network, which has an introduction.

The operating principle of the printing press is the same, except that there is an additional set of computer plates. If you know how to use a computer, you can do it

Buying a brand on a computer for printing and typesetting will definitely not meet your requirements. At present, most of the brand machines are used in business and family. And your use needs a relatively high-frequency CPU with a considerable second-level slow inch, which should be above the PD820.

AMD's doesn't have to think about it at all. Then there is a certain amount of memory. At least 1g, preferably 2g

It's also better to have a higher graphics card, and it's better to use a card for typesetting. It would be better to use x1300 or more. And remember not to use liquid crystal on the monitor, which will seriously affect your effect.

At the same time, it is not recommended to use large size flat flats. It is best to be 17 inches, and 19 inches is fine. Same reasons as above.

Also, if you want to directly connect to printing, printing presses and other things, a *** motherboard is also very necessary. This ensures your longevity.

The total cost is about 4,000 yuan cheaper. It's expensive, and 6000 is very, very sufficient.

Digital Publishing Direction Computers should be equipped with high !!

Not very high....My friend just came to a small advertising shop, by the way, printing, his computer was bought in 2009

Depending on what kind of requirements you have, generally printing foreign books must be professionally PS machines, domestic ones are 7000-9000, and foreign ones are about 15000

That's pretty high. Preferably Apple's desktop.