101, How to solve the alarm of X axis drive?

My machine tool is sometimes like this, usually turn off the power after five minutes and then turn on, this situation usually occurs in the summer, last summer my machine tool opened ten minutes on the alarm, called the manufacturer many times to solve.

Usually there are the following possibilities: 1 The driver wire is not in good contact, each of your screws is tight, 2 The weather temperature is too high, use the electric fan to blow on the electrical cabinet 3 The private server fan is broken or the electrical cabinet fan is broken, pay attention to the private server fan only when the temperature is high, on the contrary, do not turn, do not see that it is not turned, 4 The driver is really broken, this possibility is too small, my is in the summer when the electrical cabinet is broken by the fan, after the change has never been alarmed, this fan must keep turning, not turning is broken.

How to disarm the CNC X-axis drive.

1. Whether the parameters of the machine tool have been modified;

2. Whether the limit switch of the machine tool is damaged or water.

This situation will occur after the power is cut off when the Z-axis tool is adjusted or the Z-axis zero point is set to the tool, and the driver alarm can be solved by restarting the machine.

Usually turn off the power after five minutes and then turn on, this situation usually occurs in the summer, last summer my machine tool opened ten minutes on the alarm, call the manufacturer many times to solve, usually there are the following possibilities 1 drive wire contact is not good, each screw is tight 2 weather temperature is too high, use an electric fan to blow on the electrical cabinet 3 private server fan is broken or the electrical cabinet fan is broken, pay attention to the private server fan only when the temperature is high, on the contrary, do not turn, do not see that it is not turned, 4 the driver is really broken, This is too unlikely. Mine is in the summer when the electrical cabinet fan is broken, after the replacement has never called the police, this fan must always turn, not to turn is broken.

The X-axis drive with rock brake alarm may be caused by a variety of reasons, such as loose cables, motor failures, sensor failures, etc. To dismiss the alarm, you can try the following methods:1

Turn off the device and check that the cable is fully connected, then plug the cable back in. 2.Check whether the connection and wiring of the motor and sensor are normal, and whether the damaged parts need to be replaced.

3.Check that the equipment has been subjected to vibration or other external force halls that could lead to loose parts or mechanical damage. 4.

If the above methods cannot solve the problem, it is recommended to contact the equipment manufacturer or corresponding maintenance personnel for maintenance.

Summary. Pro-<>

211 alarm refers to the end alarm of the CNC X-axis drive, which is usually caused by the failure of the transmission system or the improper setting of the transmission system parameters. To solve this problem, the first thing to do is to check whether the transmission system is faulty, and if it is, it needs to be repaired; Secondly, it is necessary to check that the drivetrain parameters are set correctly, if not, they need to be set again.

What happened to the CNC X-axis drive terminal 211 alarm?

The pro-<> 211 alarm refers to the terminal alarm of the CNC X-axis drive, which is usually caused by the failure of the transmission system or the improper setting of the transmission system parameters. To solve this problem, first check whether the transmission system is faulty, if it exists, it needs to be repaired; Secondly, it is necessary to check whether the parameters of the Zen transmission system are set correctly, if not, they need to be set again.

It's good to just turn on the wiring, and the alarm will start after more than ten minutes of starting, does this have anything to do with the voltage?

This situation may be caused by voltage instability, you can check whether the power supply voltage is stable, if the voltage is unstable, you can consider using a power regulator to solve it. In addition, you can also check whether the setting parameters of the CNC X-axis drive are correct, if the parameter setting is not correct, it will also lead to an alarm.

The parameters have not been moved, that is, it is normal to move from the old factory to the new factory and connect the power supply and turn on the machine for ten minutes.

The <> suddenly appears 211 alarm, it may be that the motor coil is burned out, or the servo drive stove is cracked and closed, you need to check whether the motor coil is burned out, whether the servo drive is faulty, if the motor coil is burned out, you need to replace the new motor coil, if the servo drive is faulty, you need to replace the new servo drive.

101,How to solve the X-axis drive alarm?

How to remove the alarm of the numerical control number high X-axis drive 1, whether the parameters of the machine tool have been modified; 2. Whether the limit switch of the machine tool is damaged or the fiber water is judged. This situation will occur after powering off when the Z-axis cutter is adjusted to make up or the Z-axis zero point is set for the excavation imitation cutter, and the driver alarm can be solved by restarting the machine.