The roller shutter didn t start to get it right, are you in trouble?

Hello, the roller shutter began not to be done, and then it is very troublesome, and you may have to disassemble it and re-do it, specifically like this, I hope it can help you!

If you don't get it right at the beginning, it's still more troublesome to get it again, so you have to remove it and get it done.

It's not good to get it when it's not done at the beginning.,Of course, there's some trouble.,After all, it's to start again.,Re-do it.,Of course, you'll avoid it.,It's going to be more troublesome when you die.,But be patient.,I think it should be okay.。

The roller shutter didn't start to be done, and it won't be troublesome to get it again, at most it can be removed and reinstalled.

Hello friend, the roller shutter is not done well, and it will definitely be troublesome to get it again, and it may not be so easy to get it if you are doing it, I hope it can help you.

Ah, if this inspection is not done well at the beginning, you can do it again, and then ask the master to help install it again, it is a little troublesome, and it is not very troublesome.

Is it troublesome if the roller shutter starts to be done well? Actually, it's not troublesome, you just find the installation team and let them fix it for you.

It is best to get the roller shutter right at one time, so that it will roll up smoothly, and it will be more troublesome to get it again.

The roller shutter is not done at the beginning, it is very troublesome to get it, and it is best to do it at one time to ensure quality and save costs.

If you don't get it done at the beginning, then you have to do it again, because if you don't do it well, someone else is likely to pull the gate down, and then there is no point in you getting the check.

The roller shutter didn't get it right at first, and it was really troublesome to get it a second time.

In fact, you have to find a professional for your roller shutter door, just adjust it, and there is not too much trouble, just see if it will?

It shouldn't be too troublesome, find a master, and ask him to fix it for you.

If the roller shutter is not installed, it is also very uncomfortable to use, and it is very troublesome to get it again, so it is best to install it at one time.

If you don't get the roller shutter at the beginning, it will definitely be troublesome to get it for a while, so it's better to get it all at once.

Didn't you get it in trouble again if you didn't get it right? If you don't get it right the first time, the second time will definitely be more troublesome than the first time, but we still have to do it, and if we don't, it's even more troublesome.

Whether he's in trouble or not, you just put it down and roll it all over again. Because you can't do it like that.

In the end, it's actually more troublesome, because the data still needs to be tried by yourself.

No way.,It's a little troublesome.,It's normal.,I'm basically in the program every day.。

If it's already installed, it might be a bit of a hassle if you go back and try it again!

The second amendment will certainly be troublesome, but there is no way, and the need for revision is a must.

It should be that the link is not connected, and if you get it again, you have to get it!

In this case, you will have to remove it and reinstall it. It's not worth it if you don't tear it down and get it.

It may seem like a hassle to you, but for professionals, it's really a piece of cake.

Oh, I have to do it all over again, so what can I do?

The roller shutter was not done well at first, and it was more troublesome to get it again.

If you don't get it right, you may be doing it, but it's a little troublesome, you can also look for it, um. How to deal with the technical essentials and the information to achieve the purpose you want?

Roller shutters. I didn't get it right at first, so do you get into trouble again? It's not a hassle to get it again.

I didn't get it at the beginning, and then I got it, and then I got it, and I got it? That's what tears are doing, and if you don't do it, it will be troublesome to do it after graduation.

Summary. Extended information: the roller shutter door plays the same horizontal separation as the role of the wall, it is composed of 13 parts, such as curtain plate, seat plate, guide rail, bearing, scroll, box, control box, rolling door machine, limiter, lintel, manual quick release switch device, button switch and safety device, etc., which are generally installed in the part that is inconvenient to use wall separation.

Roller shutter doors are suitable for commercial facades, garages, shopping malls, hospitals, factories and mines and other public places or residences. In particular, the door opening is large, and the place where it is inconvenient to install the ground door body plays a convenient and fast opening role.

When the roller shutter was lowered, it was blocked by the door, and what should I do if I can't go up and down.

Hello, I am inquiring for you, please wait patiently for about five minutes, now the number of people waiting is relatively large, I will reply to you immediately

Hello, glad to answer for you. When the roller shutter door was put down, it was blocked by the door, and the reason why it could not go up and down was: the door panel was deformed and stuck, and the solution was to correct or replace part of the door piece by yourself: the motor stroke was changed and the stroke was readjusted.

Extended information: the roller shutter door plays the same horizontal separation as the role of the wall, it is composed of 13 parts, such as curtain plate, seat plate, guide rail, bearing, scroll, box, control box, rolling door machine, limiter, lintel, manual quick release switch device, button switch and safety device, etc., which are generally installed in the part that is inconvenient to use wall separation. Roller shutter doors are suitable for commercial facades, garages, shopping malls, hospitals, factories and mines and other public places or residences.

In particular, the door opening is large, and the place where it is inconvenient to install the ground door body plays a convenient and fast opening role.

Dear I hope the above will help you If you are satisfied with me, please give me a thumbs up

The solution to the roller shutter that is stuck and can't be pulled down:

First of all, the chutes on both sides of the roller shutter door should be inspected to see if there is any damage, and if necessary, it should be repaired in time; Then pull the roller shutter door to see if the direction of the roller shutter door is deviated, if necessary, the direction of the roller shutter door is correct; If the above situation does not appear in the fruit shutter door in front of the cave, you can drip butter in the chute, and if it is not possible, you can ask professionals to repair it.

Electric roller shutter door maintenance method:

1. When using the electric rolling shutter door, it is best to keep the voltage and controller of the electric rolling shutter door in a stable state, and ensure that the installation position of the electric rolling shutter door is dry. In addition, the remote control of the electric roller shutter door should not be turned on at will, and once it is found that the wires are wrapped around the roller shutter door, it needs to be dealt with in time.

2. Regularly check the opening and closing of the electric roller shutter door to ensure that the electric roller shutter door can operate normally. In the process of inspecting the electric rolling shutter door, it is necessary to prevent the electric leakage draft rolling shutter door from reversing, rushing to the top and bottoming, once these three situations occur, it is necessary to stop rotating in time, and cut off the power supply of the electric rolling shutter door.

3. Regularly check the manual switch of the electric roller shutter door to ensure that the manual switch of the electric roller shutter door can be used normally, so as to avoid the failure of the electric roller shutter door in case of emergency, which will cause safety accidents.

Summary: When the rolling shutter door fails, if you can't solve it, you should immediately ask professionals to come to the door for maintenance, so as not to cause secondary damage to the rolling shutter door. <>

Hello dear! We'll be happy to answer for you. Will the roller shutter jammed on it affect the main gate Answer:

Kiss has a certain impact 1 A large part of the reason why the electric roller shutter is stuck is because the roller shutter of the guide rail is stuck on the guide rail, and half of this kind of problem can be easily solved by prying the stuck place with a screwdriver. 2 Remember, when the screwdriver is leveraged, you must remember to turn off the power. If you are not careful, the roller shutter is stuck halfway down or up halfway, and this kind of problem must be good at observing.

3. A large part of the reason why the electric roller shutter is stuck is because the roller shutter of the guide rail is jammed on the guide rail, and half of the problem of cover rolling can be easily solved by prying the remaining part of the stuck object with a screwdriver. Thank you for your patience. If you are satisfied with my service, please give a thumbs up, and I wish you all the best!

Peace and joy!

Summary. Hello dear, the roller shutter door does not pull is the roller shutter dan spring is broken, the direction is not correct, in this case there will also be a bad pull, or can not pull down. As long as the roller shutter shaft is disassembled, the internal deformed shrinkage dan spring is replaced, and the service can be restored.

Because the operation is more complicated, it is better to ask professionals to repair and replace. In the later stage, it is necessary to pay attention to rubbing oil on the dan spring frequently, which can avoid the problem of deformation. <>

The roller shutter won't pull what is broken.

Hello. Hello dear, the roller shutter door does not pull is the roller shutter dan spring is broken, the direction is not correct, in this case there will also be a bad pull, or can not pull down. As long as the roller shutter shaft is disassembled, the internal deformed shrinkage dan spring is replaced, and the service can be restored.

Because the operation is more complicated, it is better to ask professionals to repair and replace. In the later stage, it is necessary to pay attention to rubbing oil on the dan spring frequently, which can avoid the problem of deformation. <>

Extended information: the roller shutter door plays the role of horizontal separation like the wall, it is composed of curtain plate, seat plate, guide rail, bearing, scroll, box, control box, rolling door machine, limiter, lintel, manual quick release switch device, button switch and safety device and other parts, generally installed in the part that is inconvenient to use wall separation.

<> "What's going on with the roller shutter can't be pulled down."

It may be that there are too many debris in the track and the road is not cleaned, or the one who dissipates it is rusty inside, which will affect the operation and appear stuck and unable to pull it down. In this case, we need to clean the roller shutter track frequently to ensure that the track is not blocked and the roller shutter can be pulled down, and in the later use process, we also need to clean it frequently to avoid the same problem.

It is possible that the chutes on both sides are damaged due to friction during long-term use, and the roller shutter cannot be pulled down smoothly. In this case, it is necessary to repair the damaged area first to ensure that the chute is not abnormal before continuing to use.

It is also possible that the shutter spring is deformed and the direction is not correct, in this case, it will also be difficult to pull, or it will not be able to pull down. As long as the roller shutter shaft is disassembled, the internal deformation of the shrink spring can be replaced, and it can be restored, because the operation is more complicated, it is best to ask a professional to repair and replace. In the later stage, it is necessary to pay attention to the oil rubbing of the spring frequently, which can avoid the problem of deformation.

If the drive has not been lubricated, it is prone to friction and damage, and if the wear is severe, it will not be able to pull it off. In this case, you can add some lubricating oil to the drive, and the chain should also be added to pull it down smoothly. Similarly, in the later use, it is necessary to refill the lubricating oil regularly.

If the reel of the roller shutter deviates from the chute, it will also be unable to pull down, and the reel is relatively heavy, which is very dangerous in the case of derailment, and it is easy to fall and hurt people. If you can't put it in the chute yourself, be sure to find a professional to solve it.

Seeing this, I already have an understanding of what happens when the roller shutter can't be opened.