Electronic Gear Flow!! The name is a bit awkward, please forgive me

o, the overload-based electronic dragon OTK card set. Mobile City Fortress,The bribery of the Demon Palace is the best t.,Although the Demon Palace is good, it's a loss card.,Add 2 blood generations to facilitate gear pulling gears and then out of the overload OTK opposite.,Super fusion under 1 is enough.,Put some defense cards with a roar.,Otherwise, the defense is too weak and it's easier to be otk.

Gears are gears.

Electrons are electrons.

The two decks are not in good condition, so why bother together?

DNA modification surgery is definitely a sore thing, and the actual combat effect is very poor.

The output power is definitely insufficient, and it is difficult to kill people if you think about it only with an overload dragon.

The defense is absolutely insufficient, and it is easy to be OTK by various decks

Although the gears are theoretically not lost, sometimes the full hands of gears are definitely a headache.

Well, it's actually recommended to tear it down and start over, which may be a bit harsh, but I hope you can accept it in order to improve the dueling water.

I think you can just change it to a mechanical set, put some Soga and Xiao Soga or something, and then the restriction will be lifted directly OTK, but your gear is good, and you will never lose your hand. You can put the kind of technic that loses your hand, but watch out for the tire dragon. For more information, see the American Championship Deck (which was over-9000 HP after a restriction was lifted).

If the gears. It is recommended that the group limit the type of card deck because the chain of gears is not a loss card. Forbidden special tricks to kill the mainstream electronic dragon plus DNA should be a monster ready to fuse each other, right?

This deck has not been measured, but the effect of the previous group of small spaceships + DNA + warrior obliteration + future warriors is not ideal.

The electronic gear ratio is to achieve different pulse equivalents by changing the sub-doubling of the electronic gear ratio.

The accuracy of the servo system is the encoder.

, but this is only a servo motor.

accuracy. In practice, different mechanical structures are connected, such as ball screws.

Worm gear and worm pair, the pitch, the number of teeth and other parameters are different, and the minimum unit of movement is moved.

The amount of motor rotation required is different.

The electronic gear ratio is an example of matching the number of motor pulses with the minimum amount of mechanical movement

The lathe uses a 10mm lead screw, then the motor rotates to move 10mm, and the motor needs to rotate 1 10,000 times for each movement.

If a 5mm lead screw is connected and the diameter is programmed, 1 5000 revolutions per movement is required, which is the function of the electronic gear.

This is the same as Fanuc's flexible gear ratio.

Here's an example of how to do it.

It is known that the resolution of the servo motor is 131072 pr and the feed of the ball screw is pb = 8mm.

1) Calculate the equivalent of the feedback pulse (how much does a pulse go)? lo=2) What should be the electronic gear ratio if the command pulse equivalent is required to be .

Electronic gear ratio

3) The rated speed of the motor is 3000rpm, what should be the pulse frequency?

fc=Answer:

1) Calculate the equivalent of the feedback pulse (how much does a pulse go)?

lo= 8mm/131072

2) What should be the electronic gear ratio of the required command pulse equivalent of ?

lo electronic gear ratio 1000=

3) The rated speed of the motor is 3000rpm, what should be the pulse frequency?

fc electronic gear ratio = 3000 60 131072

The formula for calculating the electronic gear ratio.

If the pulse is not doubling, then the electronic gear ratio pulse equivalent means that actually 1 command pulse goes in millimeters, and now, 2500 input pulses go 5 millimeters, that is, 1 input pulse goes in millimeters, and this number multiplied by the electronic gear ratio is equal to the pulse equivalent.

Electronic gear ratio = [(number of pulses in one revolution of the motor encoder * 4) (the distance of the load shaft to move the load in one revolution and the distance of the command transfer in one pulse)]*1 n The specific number can be substituted.

What about the pitch of the ball screw? And whether you are directly connected or trained through a belt wheel, give me the connection mechanism and I will calculate it for you.

The flow of electrons enhanced by SD26 is roughly at the second-line level, probably not too strong in any group, and the variants are more diverse.

Shapeshifter is a fun level, and can focus on the Tool Dragon, or it can be a Celestial Dragon like the Waste Two, but it is more unstable.

Mecha Gear Gears and Karakuri Gear Gears have good competitive abilities, and from time to time you can see some of the top positions, and the gear gears themselves can be used as excellent add-ons for many mechanical family decks.

At present, the electronic network of electronic dragon +R5 is more, and some of the fusion components are invested and some are discarded. Except for the electronic network, the E-Dragon 3 can be used as a safe area, and can be pulled out by a whirlwind or a magic flower pot or wait for it to send it to the grave by itself, and it can pull all the except things on the field, and can make an OTK or strong suppression field at one time. R5 has the support of a baby star or a solar sailboat, and there are a lot of powerful monsters in R5, and the Pleiades can be a major workhorse.

The faucet has an electronic repair factory, which can be used as a small black hole. If you invest in the fusion support of the electric reputation and the racket, you can play a much more stable OTK than before. You can search for related card sets to find some ideas for reference.

You can try to mix with the heritage or wait for 808 to come out and mix with the ancient relics.

Transformation fighters can go to the transformation fighter bar to turn over the boutique area, it is difficult to compete"Look at the hit"bar.

The gear gear retrieval point has a strong ability to earn more cards, there are a lot of upper card sets, so a good reference is easy to find, the pits are more, the gear gear is in the front to earn cards and cover a bunch of pits in the back field to exchange resources, and the clever old can wait for the early pit to make up enough hand cards to step on the opposite pit when the otk

Expert answers: non-circular gear and special gear transmission design (Li Fusheng), research on surveying and mapping design methods of non-circular gears, "non-circular gear surveying and mapping methods", has been sent to your mailbox, please check!

The lead of the screw is 10mm, and the pulse equivalent is, so it is concluded that 10 pulse screws are required to make one turn.

8192/1000=1024/125.This is the electronic gear ratio.