IS THERE A PROBLEM WITH A 65MM SMOKE VENT ON THE KITCHEN WINDOW BEAM?

Treatment suggestions: chisel the hair on the inner wall of the small hole, remove the floating slurry, clean it up, moisten it with water, seal one end, pound the slightly expanded concrete of the same grade or one grade higher from the other end, tamp it, and maintain it well.

Installation of load-bearing beams:

1. After the position of the load-bearing beam is determined, the load-bearing beam is fixed with expansion bolts, and after the host is positioned, concrete is poured for forming.

2 The technical requirements of load-bearing beam installation are that when the load-bearing beam is installed, the part that extends into the wall must exceed the center of the wall by 20mm, and the total length is not less than 75mm, in addition, the iron plate should be welded into one with the structural reinforcement of the wall, and its levelness error should be less than 1 1000, including transverse and longitudinal.

Whether the drainage is smooth.

As an area where water is often used, the drainage problem of the kitchen is the key point that needs to be paid attention to during acceptance. Check the drainage of the kitchen sink to see if it's smooth and fast. If there is a floor drain on the kitchen floor, then the floor should have a certain angle of inclination or a diversion channel to facilitate the discharge of water on the ground to avoid water accumulation on the ground.

It should be noted that for the kitchen with floor drain on the ground, the entire floor should be waterproofed like the bathroom, and the waterproof test should be carried out in the same way during acceptance.

Second, the kitchen ventilation problem.

The more serious problem in the kitchen is the problem of oil smoke, so the ventilation performance of the kitchen is also a place to pay attention to during acceptance. In general, the area of the kitchen window should reach one-tenth of the usable area. In order to be able to install a range hood, it is also required that the diameter of the exhaust holes in the kitchen reach fifteen centimeters.

3. Acceptance of walls and floors.

The walls and floors in the kitchen are tiled, which not only looks clean and tidy, but also makes it easier to tidy up. In the acceptance, it should be noted that the wall tiles can not have obvious color difference, the tiles can not have cracks and damage, and the gap between the wall tiles and the wall tiles should be evenly suitable.

In addition, it is necessary to pay attention to these contents when accepting the tiles on the floor, and also pay attention to whether the floor tiles laid on the kitchen floor are non-slip floor tiles. The performance of floor tiles and wall tiles is different, so it is important not to mix them.

Fourth, the acceptance of the kitchen ceiling.

The smoke in the kitchen is very heavy, therefore, the ceiling of the kitchen will generally be hung on the whole ceiling, and the materials used in the ceiling should generally be fireproof and moisture-proof. During acceptance, it is necessary to pay attention to check whether the installation of the ceiling is smooth, and there can be no deformation and arching.

5. Acceptance of cabinets and kitchen utensils.

The importance of cabinets to the kitchen cannot be overstated, therefore, when it comes to inspecting the kitchen, the inspection of the cabinets and some other kitchen utensils cannot be ignored. The board used in the cabinet should have good waterproofness, and the edge of the board should be well sealed. The part connected to the sink is easy to get wet due to water, so the edge sealing of the sink must be done well after installation, otherwise the water will leak through the gap in the sink when used in the future.

In addition, it is also necessary to check whether the cabinet door is installed symmetrically.

Whether it is feasible to open an 18 cm hole in the upper ring beam of the kitchen is a variety of factors that need to be considered, such as the structure, strength and stability of the ring beam, as well as the size and installation method of the smoke machine. If the strength of the ring beam is sufficient, and the distance, size and position of the hole from the ring beam meet the requirements of the code, then it should be feasible to open an 18 cm smoke machine hole. However, before proceeding with this project, it is recommended that you consult a professional architectural designer or engineer in a related field, who can provide you with more accurate and reliable opinions and suggestions according to the actual situation of the site and the requirements of the specifications, so as to ensure the safety and quality of the project.

Hello, the size of the hole of the smoke machine needs to be set and confirmed according to the model of the smoke machine and the size of the air inlet. If your hood model matches the size of the air inlet, and the 18 cm hole spacing meets the local building code and safety regulations, then it is also possible to make holes in the ring beam. It is recommended that you consult a professional decoration company or the technical support department of the smoke machine manufacturer for more specific advice and guidance.

In addition, it is also necessary to pay attention to safety issues such as the height of the flue and the position of the potato, and carry out the construction in accordance with the local building code and safety requirements.

Hello dear! Generally speaking, it is okay to open an 18 cm smoke machine hole in the upper ring beam of the kitchen. However, the suitability of the base game needs to be considered according to the following factors:

1.Size and power of the hood: If the size of the hood is too small or the power is insufficient, it may not be able to effectively discharge smoke and oil smoke, affecting the ventilation effect of the kitchen.

2.The size and layout of the kitchen: If the kitchen area is small or the layout is not reasonable, it may lead to poor exhaust of the smoke machine, and other ventilation methods need to be considered.

3.The material and structure of the ring beam: If the material of the ring beam is not resistant to high temperature or the structure is not as strong as the front stool, it may affect the installation and use of the smoke machine.

Therefore, before installing the smoke machine, it is recommended to consult a professional kitchen designer or smoke machine installation engineer to evaluate and design according to the actual situation. Dear to the trip is all my reply, I hope to help you, I wish you a happy life