How do I connect to the router s network?

Your question is simple enough.

In a nutshell, you want to probe the network and make sure that there are people you want to communicate with among these possible nodes. This is an invasion. It's hard to perfect the answer.

Fortunately, domestic netizens are fond of garbage, and you may be able to use very "secure" instant messaging software such as QQ and MSN.

If you want to communicate with him, you have to go to his network, if TP-Link's router network is encrypted... Then you can't help it. If it's not encrypted, then you can communicate with him according to the LAN chat that comes with the system as mentioned above.

There is also a signal that travels in a straight line, and there is really no way to use a dead method, so I won't talk about it.

The installation and setup of the router is as follows:

1.First connect the line, you can refer to the figure below.

2.After the line is connected, open a browser, enter the management address and management password of the router, and then enter the router background (the login address and login password of the specific router can refer to the manual or the label on the back of the router).

3.Once you've logged in to your back-office, select Quick Settings, then click Next.

4.Choose the way to access the Internet, usually ADSL users choose the first PPPoE, if you use other network service providers, then choose the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

5.Enter the password applied for from the network service provider, and go directly to the next step after entering.

6.Set the wifi password, try to make the alphanumeric combination more complicated, and it is not easy to be rubbed off the network.

7.After entering it correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

The router needs to be set up in the background of the router to connect to other routes

1.Use a computer to connect your own router into the background management width management page (how to enter the router background manual has an introduction), your router should be entered into the settings, and the IP address of the secondary LAN port is different from the IP address of the main router. Disable DHCP and save the restart.

Further reading: Attention to the problem:

1) The connection principle of the router: the computer can only be connected to any one of the LAN ports of the router, which is a prerequisite for entering the settings interface. Moden (moden), optical modem, or home network cable can only be connected to the WAN port of the router, which is a prerequisite for the router to be able to access the Internet.

2) After the installation of the Mercury router is completed in accordance with the appeal, the computer will not be able to access the Internet temporarily, and when the Mercury router completes the Internet setting, the computer will automatically be able to access the Internet, and it is no longer necessary to use the "broadband connection" on the computer to dial up the Internet.

3) In addition, when setting up the router, you don't need a computer to be able to access the Internet, as long as you connect the computer to the LAN port of the router with a network cable. Many novice users often ask me, how can I set up a router when my computer has no network? Please don't ask such questions again.

4) After the Mercury wireless router is successfully installed, the SYS indicator on the device will flash, the WAN interface will be solid or flashing, and the port connected to the electric dismantling mountain brain in 1 2 3 4 will always be on or flashing.

Here's how to connect the host computer to the router:

Tools required: computer, router, network cable.

1. Although we are setting up a wireless connection, a network cable is still needed. First, plug the broadband into the WAN interface, then connect one end of the other network cable to the LAN port, and the other end to the computer, and plug in the power supply.

2. Then open the browser input, enter the interface of the router settings, and select ADSL dialing here.

3. Enter the broadband account and password below, and the router will automatically identify whether the broadband is connected to the Internet.

4. The following is to set the name of the wireless signal and the wireless password, and the name of the hole or lack of wireless signal is the name we see when searching for the wireless signal. After the setting is completed, click OK below to complete the simple setup, and you can surf the Internet.

5. The wired connection method of the router, because many desktops do not have wireless devices installed, so this is mainly used on desktops. Or plug the broadband into the WAN port first, and connect the computer to be connected to the LAN port with a network cable.

6. Then open Internet Protocol version 4 in "Local Connection".

7. Set the IP address and DNS address here. The IP address is compatible with the network segment of your local Luna, which can be found on the router, and the writing range is 1 254, and the default gateway is late to fill in the LAN address of the router. DNS addresses should be treated differently from place to place.

You can also click directly to automatically obtain IP addresses and DNS addresses.

8. Finally, log in to the router and complete the ADSL dial-up setting to access the Internet.

The wireless bridging mode and the router cascade mode can be connected to other people's routers, but the wireless bridging mode is greatly interfered by the building, and the signal is unstable, so the wired connection mode is generally used.

The router cascade settings are as follows:

1.First, connect the computer to the LAN port of the slave router, and change the IP address of the slave router to a different network segment address, as long as it is not in the same network segment as the main router. For example, most router addresses are, and we just need to change from router address to one;

2.Then turn off the DHCP function from the router in the settings;

3.Finally, connect the network cable from the main router to the LAN port of the slave router (any one is fine), note that it cannot be the WAN port.